Kirby G5 Bagged Upright Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

The power use of a Kirby G5 is minimal, only 600 Watt. This, compared with the average vacuum cleaner, will lead to a considerable reduction of the electricity bill.
It`s also important to pay attention to the vacuum cords. Tishko recommends checking them daily. Replacing a cord might cost $85 in labor and up to $130 for the new part.
As stated in the referenced letter, damaged or defective cords can be replaced so long as they return to their “approved” state.
Three-prong plugs are polarized. These plugs have a big prong, a smaller one and a rounded grounding prong. The round prong is for safety purposes, so never remove or change it to fit a different outlet.
Kirby vacuum cleaners are made of die cast aluminum where most other vacuums are made of plastic. This makes the Kirby vacuum more durable than other model on the market. This is why the average lifespan of a Kirby is over 30 years.
Kirby vacuum prices are higher than many vacuums found at big-box stores, but that`s because Kirby vacuums are made of durable materials that will last for years. Why replace an inexpensive vacuum over and over again when you can purchase a Kirby vacuum? This complete home cleaning system that will last for a lifetime.
As a general rule, if the repair is going to cost less than half the cost of a new vacuum cleaner, it`s best to go ahead and get it repaired. When the service tops half the price of a new machine, it`s probably best to invest in a newer model.
Regardless if a cord is damaged by age, heavy use, pinching, or bearing too much weight (when an appliance is hung by its cord), a damaged cord increases the risk of electrical shock, fire, or electrocution, and should NOT be used. “The electric cord on your appliance contains a live wire that is securely insulated.
The average life expectancy of a mid-range vacuum cleaner is about six years. You can fix or replace things like blocked filters, jammed brush rolls, frayed hoses, worn-out stick vac batteries and broken accessories yourself.
Test for a potential short circuit by touching each prong on the AC side of the power cord. If the multimeter beeps, your power cord is bad and must be replaced immediately. If your power cord is shorted, do not attempt to replug the cord into the AC outlet.
Most carmakers recommend replacing spark plugs and wires every 30,000 to 50,000 miles. However, some factors – including engine type, driving habits, and weather conditions – can affect how often your spark plugs and wires need to be replaced.
Recycling Power Cords

To recycle your old cords, e-waste facilities are your best option. Many communities now have dedicated e-waste recycling facilities, either run by private companies or by the local government. Best Buy is another popular e-waste recycler, and power cords are just one type of item they accept.

An AC adapter supplying electricity at a higher voltage than required will cause the connected device to run hotter. Sending power at a higher voltage will also shorten the lifespan of the device and may fry its internal circuits.
Both kinds of outlets feature hot and neutral wires, but the big difference is that three-prong outlets have a grounding wire, while two-prong outlets don`t have one. Since three-prong outlets feature this grounding wire, they`re much safer than two-prong outlets.
NEMA 1-15P: Two-prong plug.

The Non-polarized version has two equal straight blades. The Polarized version features 2 blades with one being wider.

It`s unsafe and could result in electrocution. The problem with two-prong outlets is that whatever is plugged into them is not grounded. (We won`t go into the ins and outs of grounding here but just know that three-prong power cords come with appliances that require grounding to be safe.)
Resources. A room will have to be rewired if there isn`t a ground present. However, if you want to have a grounded, three-prong receptacle without rewiring, you can also use a ground fault circuit interrupter (GFCI) found at any home center.
Homeowners owning older dryers with 3-prong cords are sometimes perplexed when they move into a home that has a newer 4-slot outlet. In this instance, the solution is to replace the old 3-prong cord with a 4-prong cord to match the new outlet. Fortunately, it is a very easy project.
And an extension cord with a retractable reel takes almost all of the cord headache out of the vacuuming equation. To use one, find as central of a location as you can, preferably in a spot that won`t cause you to wind around too much furniture, plug in your extension cord, and plug your vacuum cleaner into that.
The Kirby Home Company warrants that the product shall be free from defects in material and workmanship for three (3) years from the date of purchase when the Kirby system is used for residential consumer purposes.
For more than 100 years, every Kirby has been handcrafted in the United States from die-cast aluminum.
The Dyson vs. Kirby vacuum cleaners debate can be complicated, as these brands are so different. If it comes down to price or size, Dyson will probably get the upper hand — but for all other vacuuming considerations, Kirby is the way to go.
If you demand the absolute best in your vacuum cleaner, you can`t go wrong with the Kirby Avalir 2. This trusted solution is built to last, so it will deliver years of deep cleaning. You`ll never regret investing in a high-quality vacuum that makes your life easier.
The price of vintage Kirby vacuum cleaners can vary widely, depending on their age and condition. The least expensive ones are probably worth about $100 and high-end models might sell for $2,000 or more. But if you`re looking to buy one that hasn`t been refurbished, expect to spend several hundred dollars.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Electrolux Epic 6500SR Full Bag sensor working, Does not Reset properly
ANSWER : The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full bag sensor is engaged. This second switch is supposed to get reset when you push the on/off switch on the outside of the machine. The full bag shutoff switch was stiff and it, therefore, was taking a couple of presses of the on/off switch to move the shutoff switch back into the running position.

Read Full Q/A … : Kirby G5 Bagged Upright Vacuum

Need to change electrical cord on g5 kirby – Kirby G5 Bagged Upright Vacuum
ANSWER : This should be fairly easy to do. With the cord unplugged, take the screw out that it holding the hard plastic cord cover onto the base of the machine. This is where the cord looks like it’s going into the bottom of the machine. The next part is a bit tricky. The hard plastic piece holding the cord in can be popped out with a flat head screw driver. On each side of the cover pop the tip of the screw driver into the side and gently pull to the side. Do this on both sides of the cover and it should come right off.
The cord should just pull out.

Put the new cord in, pop the plastic cover back on, and put the screw back in.

Let me know if you need more help.

🙂

Read Full Q/A … : Kirby G5 Bagged Upright Vacuum

Won’t start. My son was using the vacuum & Didn’t change the bag. The vacuum was making the full bag smell, but the light was’t on & it didn’t stop. I stopped him, changed the bag, checked the filter, closed the compartments & turned on the vacuum. Nothing happened. I checked to be sure that it was plugged in, that wasn’t the problem. I’ve let the vacuum “rest” for several days, It still won’t start. Any suggestions?
ANSWER : There is a reset button at the back of the powerhead. The user manual can be downloaded from the electrolux website, although I didn’t find it very useful. There was some info on how to change the powerhead drive belt.

Read Full Q/A … : Kirby G5 Bagged Upright Vacuum

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?
ANSWER : Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I’m surprised it lasted as long as it did.
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)

Read Full Q/A … : Kirby G5 Bagged Upright Vacuum

Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.

Read Full Q/A … : Kirby G5 Bagged Upright Vacuum

I own an Oreck 2310RS upright vacuum cleaner. The cord is too short for my needs. The cord I need is a two wire 25 to 30 foot cord. Where can I buy this vacuum cord and how do I connect it? Thanks, Don
ANSWER : You can buy one at a oreck store but i would tell you to use an extention cord

Read Full Q/A … : Kirby G5 Bagged Upright Vacuum

We have a Kenmore Progressive Model 116 Upright bagged vacuum with Hepa filter. It’s at least a couple years old. For quite some time now when ever we use the vacuum the vacuum motor will shut off nafter about 5 min. of use. We then need to let it sit for awhile and then we can run it again for another 5 min. The bag has been change. Any one have any ideas how to fix this?
ANSWER : I suspect that you have a restriction. The motor sounds like the thermal break is stopping the motor before damage, due to heat.
.You must witness that the entire suction and discharge side are clear. This is not always very easy, but necessary. I bet that you find something blocking somewhere…

Read Full Q/A … : Kirby G5 Bagged Upright Vacuum

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby’s are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,
ANSWER : You can get better prices from Goodvac.com

Read Full Q/A … : Kirby G5 Bagged Upright Vacuum