Dyson DC07 Bagless Upright Cyclonic Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Your Dyson DC07 has been rejuvenated with a new drive belt, allowing the brushroll to move freely while it cleaners your home.
There is a lot of confusion out there about whether or not the Dyson Ball vacuum has a belt. The answer is yes, it does have a belt. This belt is located inside the vacuum, and it helps to power the roller brush.
If your vacuum`s brush bar is not turning, the bar may be clogged from hair and other debris. Ensure that the brushbar button, which is gray and located next to the power button, is turned on. If this is not the issue, then the brushbar itself may be damaged or stuck.
Because vacuum manufacturers do not share a standardized naming system for vacuum belts, using your vacuum`s model number is the best way to ensure an accurate belt order.
Dyson Belts, Fits: All Upright Vacuum Cleaner Models Using one Belt System, 3 Belts in Pack.
If there is a strong burning smell coming from the motor area of your Dyson DC14 or DC07 then it is most likely that your motor has burnt out.
You should replace the belts on your vacuum at least every three to six months if the vacuum is regularly used. This is very important for proper cleaning.
Have you ever broken a belt on your vaccuum and didn`t have a chance to buy a new one? You can make your own out of duct tape for a TEMPORARY fix. This belt is for TEMPORARY USE ONLY, you might damage your vaccuum if you overuse this belt.
The brush roll or its bearings may be clogged with hair, threads or dirt. Make sure they are clean and the roll spins. The belt may also have slipped because it was loose. Check the fit of the new belt when it is installed.
Next to the motor, the belt on your vacuum is just about the most important part of your vacuum. Without the belt to spin the brushroll, most vacuums won`t pick up on carpeting at all! If your vacuum uses a rubber belt, check it once a month for cracks, melting, and especially, slippage.
Put on a pair of pants that fits well and stand in a relaxed position. Then wrap a soft tape measure through the belt loops so the tape is snug but not too tight. This measurement is your belt size. You may need to round up to the nearest even-numbered inch.
A Dyson vacuum cleaner has a lifespan of around 10 years. This is considerably longer than most other vacuums. So, if you`re looking for a high-quality vacuum cleaner that will last you for a long time, a Dyson could be a good choice. However, remember that Dyson vacuums are expensive.
(All full-sized machines, upright vacuums and canister vacuums, typically have a belt.) A vacuum will still create suction with a bum belt, but without a rotating brush roller, it won`t collect much in the way of dirt and debris, especially on carpets.
The brush bar button is on the left next to the power button. The suction control slider is located on the front of the cleanerhead.
As the cleaner head and filter fills with dirt and debris over time, all the built-up debris begins to emit a burnt-smelling odour. You may need to remove and clean out the vacuum`s filter. We need to advise you to stop using your machine and request that you contact your local customer support team.
Blockage – when a vacuum cleaner becomes unusually loud, it is normally because of a blockage of some sort. This is a problem that is easily solved by turning off the cleaner, check for blockages in the pipes, and remove them. You can also check and empty the canister to remove any possible blockages there as well.
If your brush is scratching your floor, or not cleaning as well as it used to, then you may want to replace your brush bar.
The carbon brushes conduct electricity from the fixed parts of the motor through the moving parts of the motor.
If an accidental jam or improper height adjustment momentarily causes the revolving brush to stop, a burn spot or a heat blister in the belt may result, causing a burnt rubber odor. In these instances, the belt is most often rendered irreversibly damaged and should be replaced immediately.
For most cars, the belt will be located at the front of the engine. When checking the belt, always make sure the car is switched off and cooled down. Your belt should be inspected with each oil change. Mechanics will normally check the belt to ensure no significant damage has occurred.
Serpentine belt replacement is easy because today`s automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning. Just rotate the tensioner, remove the old belt and install a new one.
Essentially, how the hack works is by taking an old shoelace and stringing it through the two side belt-loops on your pants that are further toward the back (your pants need to be on first). Once the shoelace is strung though, you pull the two ends of the shoelace together and tie the ends together tightly.
How to do it: Attach a strip of double-sided tape to the inside of your belt end. Line the end up so it lays flat against your belt and press to secure.
Clear the brush roll of any hair and debris and inspect by placing it on its end and spin. The brush should spin freely. If it doesn`t spin; it may be time to replace.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Need to find the belt for the brush. Every sight leads me to drive belts and I dont need that. I need a model number prefferably
ANSWER : Unscrew both bolts that are in plain sight on top of vac above the brush, then remove housing and belt is right there
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head.
My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt.
There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a
ANSWER : Yes, there should have been a white plastic sprocket on top of the bearing – in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail – only available by order to dealer repair shops....
Unfortunately to fix it you must send it to one and that would be more expensive than a new one. Just junk this chinese POS and buy another chinese POS.
Unfortunately to fix it you must send it to one and that would be more expensive than a new one. Just junk this chinese POS and buy another chinese POS.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
I’m using (or WAS using) a Eureka ”the boss” model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can’t find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?
ANSWER : First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there’s two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it’s a ribbed belt? that is the water pump belt?
ANSWER : Just taken ours apart with the same problem… found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places – the bottom of the screw wells..This means that the water tank cannot exert sufficient pressure on the valve to release the water..Only solution is a new top cover assembly
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
My model F5906-900 — problem is the brushes have stoped working… I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly… onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it’s ab
ANSWER : (1) Assure the Brush Control on the hood is NOT set to the OFF position.
.(2) Remove the brush assembly by pulling/unlatching it from base on each side.
.(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
.(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.
.(2) Remove the brush assembly by pulling/unlatching it from base on each side.
.(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
.(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn’t seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right….can you help. I am v
ANSWER : I’ve successfully used a compatible belt – Royal 104425001 .It’s still new, but for the time being at least – it works.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Eureka 5843 belt keeps slipping off of drive spindle.
ANSWER : Tough one. Typically the only 2 things that the belt contacts is the motor drive spindle and the brush roller. Anything else would only be there to protect the belt from debris. Can you turn the brush by hand and see why the belt is coming off? Is the spindle wobbly? If so, you may need another motor as I don’t think it is easy to get parts for the motor. Hope this helps and good luck!
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
