Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum\015 I just changed the bag and the motor is running but no sunction\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

If your vacuum cleaner has lost suction power, it`s time to empty the container. Vacuum cleaners come with various foam or mesh filters. These might get clogged over time if not cleaned or replaced properly. This will cause your vacuum to lose suction.
Check the Rotator Brush and Wheels

Sometimes pieces of string or other objects get wrapped around your vacuum`s rotating brush or around the wheels of the vacuum. Unplug your vacuum. Turn it over and have a look at the wheels and brush. If you see any pieces of string or objects lodged there, remove them.

The two main indicators to determine vacuum power performance are water lift and airflow. The water lift is measured in mmH2O, mbar or kPa. It represents the suction force and is the reference parameter for vacuuming liquids and heavy materials. The airflow is measured in m3/h or in l/s.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
Suction power is low

A telltale sign that the bag is full is if your vacuum cleaner`s suction power is not as powerful. If you`re noticing dirt and debris left behind despite running the vacuum over a few times, it`s time to switch out your bag.

Shop our selection of HEPA Media vacuum bags and capture 99.97% of allergens including dust, dander, pollen, and mold while blocking them from re-entering the air while you clean. Be sure to use only genuine HOOVER® vacuum bags in your HOOVER® vacuum.
Vacuum means the absence of all matter including air. As there is no air in the vacuum, air pressure will be zero.
What is a Good Suction Power for a Vacuum Cleaner? An upright cordless vacuum cleaner should have at least 100 air watts to effectively clean a variety of floor surfaces, with the best Samsung vacuum cleaner reaching up to 210W*.
Suction pressure should be kept at less than 200 mmHg in adults. It should be set at 80 mmHg to 120 mmHg in neonates.
Use Some Water

A little bit of water can do wonders for boosting a suction cup`s grip. Using warm water, rinse the whole cup so it softens it up. Shake the drops of water off the cup quickly and then put it up on the wall. That can often do the trick.

All vacuum cleaners operate based on air flowing from the opening at the cleaning head or tool, through the vacuum cleaner and the bag and/or filter system and then out the exhaust port. This airflow is created by the vacuum motor, which also may be referred to as the suction motor.
Bagged vacuum cleaners tend to lose their suction as the bag starts filling. Even if they lose suction, these vacuum cleaners can find their clog easily. The suction in bagless vacuum cleaners remains constant and is also less messy when you dispose of the dust and dirt sucked up by the machine.
It is often recommended, however, that dust bags are replaced when they`re around two thirds full or once a month. Daily and extensive use of vacuum cleaners will create a need to replace dust bags more frequently.
In general, bagged models tend to work more efficiently than bagless vacuum cleaners because they have an extra layer of protection for their filtration system. If someone in your household lives with allergies or asthma, it`s in your best interest to choose a model that will filter out the air as best as possible.
Better for allergies – Bagged vacuum cleaners are much better for allergy sufferers because there is no risk of this nasty bacteria getting released back into the air when you empty it. If you or your family suffer from pollen, dust or pet allergies, we highly recommend a bagged vacuum cleaner.
When it comes to saving the most space while storing your belongings, vacuum-sealed bags are the way to go. In fact, they can reduce the amount of storage space needed by almost 50%. While not everything can be stored in a vacuum-sealed bag (refrigerators, furniture, and other big items), these 3 things can be.
Vacuum-sealed clothes bags are allowed but not encouraged. If they alarm, the TSA officer may need to open them for inspection. For more prohibited items, please go to the `What Can I Bring?`
The Science on How a Suction Cup Works

When you press a suction cup against a wall or window, you push out the air inside it, eliminating the pressure inside the suction cup and creating a vacuum which seals the cup tightly to the surface you want it to stick to.

Clog located in the vacuum hose

Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.

Simple: the bag or canister is full and the vacuum has nowhere to store the dust it is collecting. Empty the canister or bag. If that doesn`t fix it, the vacuum filter needs to be cleaned or changed.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.

I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?
ANSWER : Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I’m surprised it lasted as long as it did.
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)

I have a Kirby G4 Vacuum Cleaner – MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I’ve had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
ANSWER : Hello,
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
ANSWER : The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal.

Electrolux Epic 6500SR Full Bag sensor working, Does not Reset properly
ANSWER : The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full bag sensor is engaged. This second switch is supposed to get reset when you push the on/off switch on the outside of the machine. The full bag shutoff switch was stiff and it, therefore, was taking a couple of presses of the on/off switch to move the shutoff switch back into the running position.

No sunction from my Hooveer windtunnel vacuum
ANSWER : Disconnect the hose from the intake hose on the back its the clear looking hose at the bottom on the back.yes you should feel suction where the bag gets connected the clog is at the bottom.but clean the filters first.your long hose i would take it outside and blow it out with a garden hose.on the bottom where the intake hose is ,take a coat hanger and bend the tip till its rounded so you don’t puncture a hole in the hose.just work it down into the tube and se if you can push the clog out the bottom ,you can put your hand over the intake hose where it connects to the long hoseand see if you have suction there,if not then the clog is in your intake hose.if you do then the clog is either in the long hose or the filters

My home has a central vacuum system hook-up but no vacuum installed. My friend upgraded his central system and gave me his Eureka Mega Boss central vacuum system and the accessories, including the pow
ANSWER : The power head requires 120 Volts. Some hoses have a receptacle in the handle for the power head plug, and the hose has a cord at the wall inlet end that plugs into a receptacle. Some hoses have a plug at the wall inlet end that plugs into a 120Volt receptacle built into the inlet. The hose plugs into this receptacle when you push the hose into the inlet. The power for this built-in receptacle is wired with line voltage when the system is installed.