Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum\015 Hi,..I have Bissel proheat x2. It works for cleaning using the hand haeld nossel. But for carpet cleaning, there is no water or solution comming out. So at the moment I can’t use it clean carpets.\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Check to see if the collection water tank outside the bladder is full. The float will activate to cut off suction. Empty the collection tank and test for suction. If there is still no suction at this time, please visit a BISSELL Authorized Service Center.
First, check to make sure the clean tank has water and/or the water & formula mixture in the tank. If your tank is empty, this could be the reason your machine is not spraying. You will need to fill your clean tank again. Reseat the tank and ensure it sits snug on the machine.
Check to see if your clean water tank is empty. The clean water tank also may not be seated properly. The brush window could also not be latched into place. Turn off your machine and check to see if the brush window is secure.
Inspect the vacuum hose for any small holes, kinks, or cracks. Any cracks or holes will decrease the amount of suction in the hose and will not allow the carpet extractor to properly remove liquid from the floor. The hose will need to be replaced if there is damage.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
In Line Filter Assembly (includes Cap & Filter) for ProHeat 2X Upright Carpet Cleaners (equipped with In Line Filters) and Lift-Off Upright Carpet Cleaners. Fits in the top portion of the foot of the Carpet Cleaner, under where the Dirty Water Tank sits on the foot.
Baking soda works wonders when it comes to lifting and removing trapped moisture. Simply sprinkle a liberal amount of baking soda over your wet carpet and allow it to sit for at least half an hour. Then, vacuum it up and enjoy fresh dry carpets.
The level you set your vacuum depends on the height of your carpet. For bare floors, use the lowest or bare floor setting, for short and medium pile carpets use a medium setting and finally, for plush carpets use the highest setting.
Fill clean water tank with warm tap water. This machine uses HeatWave Technology™ which helps maintain consistent water temperature throughout the cleaning process by redirecting the heat of the motor to help maintain the temperature of the water.
These filters can be hand washed in warm water. A mild detergent may also be used. Close the lid and return the tank back to the vacuum. Press firmly until you hear a “click”.
A: Yes, it can be used on several types of hard floors. It mentions tile, linoleum, and laminate in the manual.
Check your carpet and baseboards
Water leaks caused by plumbing problems or inadequate drainage after a significant rainfall can result in water seeping through the slab foundation and soaking the carpet padding or wetting baseboards. If you notice damp spots in your carpet or baseboards, you may suspect a slab leak.
Fortunately, the process is simple. Run a fan pointed at the wet area to help moisture evaporate. A dehumidifier also works to pull moisture out of the air and dry out the carpet. “Another option is to get rags and lay them over your damp area,” says Happy DIY Home founder Jen Stark.
It`s not unusual for DIY carpet cleaners to need eight or even 10 passes on a carpet before the water runs clear. This is especially true when: It has been a long time since your carpet was last deep-cleaned.
Hot water loosens and softens dirt more quickly, making it easier to remove, and it also helps to kill bacteria. That`s why we recommend filling up your carpet cleaner`s tank with warm water. Some BISSELL Carpet Cleaners also use HeatWave technology to keep the water hot throughout the cleaning process.
Your dirty water tank may not be secured tightly. Check the rubber tab on the dirty water tank and press firmly on all edges to secure it tightly. The accessory hose door also needs to be closed securely. Check the door and make sure it is locked in place.
If there is a clog in the vacuum, you won`t have good suction and the vacuum won`t work. The clog can be in the vacuum head, the hose or where the hose meets the actual vacuum.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.
I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate
ANSWER : Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like it should. The big draw back to this model is Bissell has obsoleted all of its parts and most are no longer available. Might be wiser to buy new.
I have a Bissel 9300-C 0714 BC Carpet Shampooer. It was working great and all of a sudden it stopped working. It still sucks up dirty water but it does not spray water onto the carpet. I can get it to spray water through the smallest hand attatchment but not through the large hand held piece on the base of the machine. I really hope you can help me, I am a dog groomer and I really need my machine to work properly. I can get it to spray water out of the smallest hand attatchment but
that’s all t
that’s all t
ANSWER : The spray jet has become clogged from the soap…. just clean it out. same thing happened to my attachment.
I have a Sunbeam Model Number 4065-000 and there is white particles comming out of the holes in the bottom. I think it is because we used tap water and there is a lot of deposits in the water. I read on the box that it was ok to use tap water and not distilled water. Is ther any way to clean the inside out to get the deposits cleaned out without affecting the possibility of doing something to the cloths that I will iron after cleaning the iron?
ANSWER : If the deposits are recent and still fairly soft, running a tank of vinegar through the machine should remove the deposits (obviously not using on any clothes, hold it over a sink). if the deposits are more stubborn, you can use a cleaning agent like CLR. rinse the tank out thoroughly after and run through a tank of clean water. good luck!
I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
ANSWER :
Call BISSELL Consumer Services.
.
1-800-237-7691
.
Mon-Fri: 8am to 10pm ET
.
Sat: 9am to 8pm ET
The Hoover Steamvac Widepath will NOT pick up water. The dispenser with cleaner DOES have water. The TANK that would receive the dirty water is NOT full. All tanks are on properly and the machine will still not pick up the used water. I found a tear in the interior hose leading to the receiving tank and repaired throughly with electrical tape. Still will not pick up the water. Any suggestions?
ANSWER : Sounds like a clogged air path (no vacuum action) from the floor pick-up to the collection tank. Take the tanks off and deal with the vacuum problem alone. The collection tank should have a air exit vent–is it clear? Check the interior hose that you repaired–is it clogged? Remove the bottom plate and inspect the air path from it. Because this machine deals with water, clogs can become like concrete! Hope this helps!
No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema
ANSWER : Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn’t squirt, check for the seal at the bottom of the tank, it needs to be on the tank, not in the hole, this is for the soap bottle also, there is a seal on the bottom of it as well. The flow indictor cap is leaking air or maybe is too tight. If you had the top cover off, make sure that the tubes are routed right so as not to get pinched when the cover is put back on, the smart mix knob should be in the water setting and that the piston is on the bottom of the smart mix knob. Pump is bad. Try running a mix of vinegar and water to see if that unclogs the lines. Is the top cover and the base tight together in the back, sometimes the top breaks loose and it will raise up and it can’t spray, just re-fasten it down.
.
.Bissel’s Number is: 1-800-237-7691, they can tell you were to get service in your area.
.
.Bissel’s Number is: 1-800-237-7691, they can tell you were to get service in your area.
No water comming onto the cxarpet
ANSWER : Remove the water tank and pull up those two red tabs unhook them and push something small thru them they are clogged up that is where your water releases it works I just did it and my bissell works great now!
