clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema
Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Your dirty water tank may not be secured tightly. Check the rubber tab on the dirty water tank and press firmly on all edges to secure it tightly. The accessory hose door also needs to be closed securely. Check the door and make sure it is locked in place.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
You are leaving too much foam in the carpet

Dirt particles stick to it, and it is this that makes your water dirty when it is sucked up. If your carpet cleaning solution is too foamy, or you leave foam in the carpet, more dirt will be attracted to it.

An optional step that we recommend if you have time is to go back over the cleaned carpet again with only hot tap water in the tank (no formula this time). This will remove any leftover formula and give your carpets an extra clean.
So, you`ve decided to buy a Bissell Power Steam Pro Carpet Cleaner and are wondering what other cleaning solutions you can use in it. Well, you can use Baking soda, Vinegar, Castile soap, or even Warm Water.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema
ANSWER : Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn’t squirt, check for the seal at the bottom of the tank, it needs to be on the tank, not in the hole, this is for the soap bottle also, there is a seal on the bottom of it as well. The flow indictor cap is leaking air or maybe is too tight. If you had the top cover off, make sure that the tubes are routed right so as not to get pinched when the cover is put back on, the smart mix knob should be in the water setting and that the piston is on the bottom of the smart mix knob. Pump is bad. Try running a mix of vinegar and water to see if that unclogs the lines. Is the top cover and the base tight together in the back, sometimes the top breaks loose and it will raise up and it can’t spray, just re-fasten it down.
.
.Bissel’s Number is: 1-800-237-7691, they can tell you were to get service in your area.

Our problem with our Rainbow E Series is that it has sucked water up and blown it out through the lower part of the hepa filter, making the filter wet and dirty. This had happened before and the repair shop did not see any problems with the machine, so we replaced the filter and were very carful not to overfill the tank and to change the water often. Now it has happened again and ruined another filter. Do you know what could be causing this issue? Can the filter be cleaned or will a new one be
ANSWER :

Thank you for allowing.us to help, please respond with further questions and concerns
..

Spanish speaking.available for all problems
..

Before you leave.feedback, ensure that your concerns and problems are addressed completely with.me.
..

PLEASE do not forget to.award/PROVIDE “POSITIVE” FEEDBACK
.



.

Hello, thank you for sharing your problem with us, I would personally be happy to provide the most accurate and up to date information for you.
.



.

1. There is no reason to waste money on an EXPENSIVE replacement. While some people may like the fact that something that may be brand new may work better, this is not always the case.
.

2. You can easily set the filter out to try as long as there is NO WET ELECTRICAL COMPONENTS, if so, you will be facing electrical damage
.

3. Once you have performed a natural or sun dry on the old filter, ensure to check your unit for anything that may have caused the back clog.
.

4. Back clogs for your model are often times associated with a BUILD UP of dirt and HAIR. YOU may always use pressure air for example at a gas station to flush out the build up.
.

5. Other occasions, users accidently build the vac WRONG causing continual backup and water going where it is NOT suppose to go.
.

6. Please visit me again if your problem persists.
.



.

.


..

Thank you for allowing.us to help, please respond with further questions and concerns
..

Spanish speaking.available for all problems
..

Before you leave.feedback, ensure that your concerns and problems are addressed completely with.me.
..

PLEASE do not forget to.award/PROVIDE “POSITIVE” FEEDBACK

I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate
ANSWER : Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like it should. The big draw back to this model is Bissell has obsoleted all of its parts and most are no longer available. Might be wiser to buy new.

No WAter My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle.
ANSWER : Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn’t squirt, check for the seal at the bottom of the tank, it needs to be on the tank, not in the hole, this is for the soap bottle also, there is a seal on the bottom of it as well. The flow indictor cap is leaking air or maybe is too tight. If you had the top cover off, make sure that the tubes are routed right so as not to get pinched when the cover is put back on, the smart mix knob should be in the water setting and that the piston is on the bottom of the smart mix knob. Pump is bad. Try running a mix of vinegar and water to see if that unclogs the lines. Is the top cover and the base tight together in the back, sometimes the top breaks loose and it will raise up and it can’t spray, just re-fasten it down.

We have the water hooked up at the back of machine. there is a spout for the water to come in and fill the ice tray.but is does not. If we turn the water on it fills up the space under the ice basket. I keep getting red light and then the two smal llight one ice and one water come on. We can hear the motor trying to fill the ice try and then lights come on. Please help me this so I can use this product. It did not come with a manual.
ANSWER : The water inlet valve on the back of unit opens when the ice maker needs water. If the valve doesn’t seal good because of sediment or wear it will continue to drip and when the water reaches the ice maker supply tube it will freeze blocking the fill tube.. You can take the water line off the valve and watch to see if it drips.
With the fill tube blocked with ice the water can drip down the back wall or drip into the ice bin or just stop up. You can use a hairdryer to thaw the tube out.

I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
ANSWER :

Call BISSELL Consumer Services.
.

1-800-237-7691
.

Mon-Fri: 8am to 10pm ET
.

Sat: 9am to 8pm ET

Shampooer I have a rainbow e series and my shampooer is not working. The tubes do not seem to be clogged and it sounds like it is trying to work but we cant get the water to come out. We pull the trigger and nothing no soap, no water, nothing. Can anyone help?
ANSWER : Aqua mates have an o-ringed valve assembly that go bad regularly reccoment having it replaced by local vac shop

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o
ANSWER : Hello,
.
.Here’s a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale sign that your belt has gone bad.
.
.Video Showing how to access and change belt:
.http://www.bissell.com/VideoRating.aspx?id=1555
.
.If you open up your machine and find that the belt is still engaged, or you replace it and this doesn’t fix your problem, please feel free to use the comment form here on this repair page and I’ll be happy to walk you through some more advanced diagnosing.
.
.If you found this helpful, please be so kind and rate my repair helpful, or leave some feedback. This is really appreciated.
.
.Chris Jones
.GoVacuum.com