Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Check to see if your clean water tank is empty. The clean water tank also may not be seated properly. The brush window could also not be latched into place. Turn off your machine and check to see if the brush window is secure.
First, check to make sure the clean tank has water and/or the water & formula mixture in the tank. If your tank is empty, this could be the reason your machine is not spraying. You will need to fill your clean tank again. Reseat the tank and ensure it sits snug on the machine.
A possible cause might be that the tank is not properly seated. To assure the tank is seated properly, pick it up and re-seat is so it sits snugly on the unit. If this doesn`t fix the problem, make sure the tank is assembled properly. To make sure they are both latched properly, pick the tank up by its handle.
Your dirty water tank may not be secured tightly. Check the rubber tab on the dirty water tank and press firmly on all edges to secure it tightly. The accessory hose door also needs to be closed securely. Check the door and make sure it is locked in place.
Naturally, all carpet cleaners will leave some moisture, which will dry out in the hours following the cleaning process. However, if the carpet remains wet long after cleaning, it`s because the final step of that process was insufficient.
Just empty the water out of the tank after each use. Doing so will prevent leaking and extend the life of your filter.
You are leaving too much foam in the carpet

Dirt particles stick to it, and it is this that makes your water dirty when it is sucked up. If your carpet cleaning solution is too foamy, or you leave foam in the carpet, more dirt will be attracted to it.

Yes, you should keep cleaning the carpet until the water is clear. This will ensure that your carpets are clean and free of dirt, dust, and other allergens. However, you should be careful not to scrub too hard or use too much water. Doing so can damage the carpet and lead to more stains in the future.
To empty the tank pull up on the rubber tab and pour out the dirty water. Fill the dirty tank with clean water and shake gently to rinse the inside. Empty the dirty water from the tank. Repeat this process until the tank is dry.
Your carpet will be only slightly damp to the touch after your cleaning. Most carpets typically need 6-10 hours to dry completely. However, it could take up to 24 hours to dry depending on the time of year your carpets are cleaned, and the air circulation, humidity and temperature in your home.
On the average, it will take approximately 2-4 hours for carpet and upholstery to dry after being carpet cleaned. To expedite the drying process, you will want to use a fan and increase your air circulation.
A: Yes it can be used as a vacuum without water.
So, you`ve decided to buy a Bissell Power Steam Pro Carpet Cleaner and are wondering what other cleaning solutions you can use in it. Well, you can use Baking soda, Vinegar, Castile soap, or even Warm Water. However, you must keep in mind that you should leave the carpets to dry after you use them.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
It`s really straightforward – all you need to do is sprinkle a generous among of baking soda over your wet carpet and let it sit. The baking soda not only absorbs moisture, but it`ll also absorb any nasty odours.
Step 3: Setup Your Carpet Cleaner

After you get out your carpet cleaner, fill the clean tank to the line with hot (not boiling) tap water. Hot water does a better job cleaning than cold but, if you boil it, you run the risk of melting parts of your carpet cleaner.

When finished shampooing, run a tank of clear water over the heavy cleaned areas (e.g. entrances and walkways). This will help remove excess shampoo and keep those areas cleaner for longer. It also helps to rinse out the shampoo from inside in the machine!
These filters can be hand washed in warm water. A mild detergent may also be used. Close the lid and return the tank back to the vacuum. Press firmly until you hear a “click”.
Steam cleaning can take anywhere from 8 to 24 hours to completely dry. However, it only takes 4 to 8 hours to dry when carpets are cleaned without the use of traditional steam cleaning methods that use large amounts of water due to their reliance on soaps and shampoos.
A general rule of thumb

A good rule of thumb is to have your carpet professionally steam cleaned at least once a year, twice if you seem to track a lot of dirt in. This way you get a good, deep cleaning and don`t let the dirt build up.

mildew and mold will develop within 24-48 hours of water exposure. Even worse, it will continue to grow until steps are taken to eliminate the source of moisture, and effectively deal with the mold problem.
Use a fan and/or box heater to blow warm air across the wet area of carpet. Warm air can hold more water than cold air, so warm air moving across the carpet will draw water out of the carpet.
‍ It varies based on the carpet`s material and fibres, how wet it is, and whether it can be hung up. The majority of carpets should be dry if left for 24 hours if the temperature and air is right.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

I do not have my users manual and have never vacuumed wet with this vacuum. How do I change it from a dry to wet vacuum.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
lost my user manual never used it to pick up water. need to know how to puit it in wet mode i want to clean the dirty water out of my pool.
ANSWER : .Vacuuming Liquids
.1. When picking up small amounts of liquid
.the filter may be left in place.
.2. When picking up large amounts of liquid
.we recommend that the filter be
.removed. If the filter is not removed, it
.will become saturated and misting
.may appear in the exhaust.
.3. After using the vac to pick up liquids,
.the filter must be dried to reduce the
.risk of possible mildew and damage to
.the filter.
.4. When the liquid in the drum reaches a
.predetermined level, the float mechanism
.will rise automatically to cut off
.airflow. When this happens, turn off
.the vac, unplug the power cord, and
.empty the drum. You will know that the
.float has risen because vac airflow
.ceases and the motor noise will
.become higher in pitch, due to
.increased motor speed.
.IMPORTANT: To reduce the risk of damage
.to the vac do not run motor with float
.in raised position

My Bissell 25A3 ProHeat wont spray water – Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum
ANSWER : I had two problems. No water was coming out of the main unit (it was working fine via the powerbrush) and the flow indicator wasn’t spinning. Because I’m out of warranty, I did two things (after trying all the options that were posted).
.1. Removed the top of the main unit. There are 4 screws on the top back lid. Once you remove those, lift the back up towards the front. The front is snapped under the bottom casing. It should come up with a little pressure, but don’t force it. With the top lid removed, I had to clean several of the rubber hosing by removing them and running under warm water. I actually used a long wooden skewer to scrape the grime in the tube. Make sure you do one tube at a time and replace in as it was before moving to the next one. While you are at it, make sure the 2 sprayers on the front are clean as well. They are either orange or yellow and rubber tubes also feed into the sprayers. After I finished, I replaced the lid. It it still wasn’t working, so I tried step 2.
.
.2. Remove the hose assembly from the main handle. 2 screws and 2 bolds (don’t lose the nuts from the back). Once the hose assembly has been removed, then lift off the top part of the handle. Once the top is off you should be able to open the front lower part of the handle exposing the additional electrical and more rubber tubbing. In the middle is rectangular looking object. That is the water heater. If you just ran the vacuum, do NOT touch this as it will be hot. Wait for it to cool. check the connections of the rubber tubing and make sure they are clean. In my case the tube going in to the heater was all blocked up with cleaner solution. Once I cleaned that up an reassembled in reverse order, the unit worked fine.
.Hope that helps you.

Not letting water out of vacuum – Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum
ANSWER : If it is not pumping water out of the vacuum that means that the pump belt is worn. Here is a link to the belt you need and a manual you can view:

Bissell 1698 Belt and Manual

My bissell proheat wont disperse water – Bissell 1698-1 PowerSteamer ProHeat Plus Upright Vacuum
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101

I have a 5.5 hp craftsman 20 litre wet Dry vacum . I have lost the manual. & have 2 questions 1) how do I change to wet vacum from dry? Also could i use the wet mode with some water in it and let it run while I am sanding dry wall to catch the dust in the water in the container? Thanks
ANSWER : # 1 myou just take the bag out make sure ytou sponge filter is in place athe top and turn it on the power switch just turns on ,machine ther is no wet dry switch just an empty bagless cannister is all you need make sure the ball outlet in vacumn is working it stops water from overfilling cannister # 2 just use the proper bag and attachment to vacumn up the drywall dust a good building supply store has special sanding attachments for vacumn so you can sand and vacumn at the same time

My bissell does not **** up water very well – Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101.
.ru

Tubing for bissell proheat – Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum
ANSWER : Normal. 0. . . . . . . MicrosoftInternetExplorer4. ...... /* Style Definitions */. table.MsoNormalTable.\011{mso-style-name:”Table Normal”;.\011mso-tstyle-rowband-size:0;.\011mso-tstyle-colband-size:0;.\011mso-style-noshow:yes;.\011mso-style-parent:””;.\011mso-padding-alt:0in 5.4pt 0in 5.4pt;.\011mso-para-margin:0in;.\011mso-para-margin-bottom:.0001pt;.\011mso-pagination:widow-orphan;.\011font-size:10.0pt;.\011font-family:”Times New Roman”;}....Hi,
.
.Here is a tip that will give you all the information you need to fix your Bissell.Proheat Vacuum Problem.
.
.Bissell Proheat Upright Wet/Dry Vacuum Problems
.
.heatman101

My bissell proheat 2x isnt letting water out – Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 .
.
.hhl