Bissell 8910 ProHeat Clear View Upright Vacuum\015 MY CLEANER WORKS GOOD BUT IT JUST STOPPED PULLING THE WATER BACK UP OUT OF THE CARPET\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

A possible cause might be that the tank is not properly seated. To assure the tank is seated properly, pick it up and re-seat is so it sits snugly on the unit. If this doesn`t fix the problem, make sure the tank is assembled properly. To make sure they are both latched properly, pick the tank up by its handle.
No, this unit does not suck water.
Hold the end of the hose below the water level in the tank to prime. With a full tank of water and the Machine off and reclined press the clean shot button `on` Wait for the clean shot to run for a few seconds, this will reprime your machine.
Check the dirty water tank and make sure there are no clogs in the hose below it. Remove the filter and clean debris from both the screen and filter. Also empty the dirty water tank and leave the filter out to dry completely before replacing it.
In Line Filter Assembly (includes Cap & Filter) for ProHeat 2X Upright Carpet Cleaners (equipped with In Line Filters) and Lift-Off Upright Carpet Cleaners. Fits in the top portion of the foot of the Carpet Cleaner, under where the Dirty Water Tank sits on the foot.
A: Yes it can be used as a vacuum without water.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

The Hoover Steamvac Widepath will NOT pick up water. The dispenser with cleaner DOES have water. The TANK that would receive the dirty water is NOT full. All tanks are on properly and the machine will still not pick up the used water. I found a tear in the interior hose leading to the receiving tank and repaired throughly with electrical tape. Still will not pick up the water. Any suggestions?
ANSWER : Sounds like a clogged air path (no vacuum action) from the floor pick-up to the collection tank. Take the tanks off and deal with the vacuum problem alone. The collection tank should have a air exit vent–is it clear? Check the interior hose that you repaired–is it clogged? Remove the bottom plate and inspect the air path from it. Because this machine deals with water, clogs can become like concrete! Hope this helps!

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.

I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate
ANSWER : Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like it should. The big draw back to this model is Bissell has obsoleted all of its parts and most are no longer available. Might be wiser to buy new.

No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema
ANSWER : Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn’t squirt, check for the seal at the bottom of the tank, it needs to be on the tank, not in the hole, this is for the soap bottle also, there is a seal on the bottom of it as well. The flow indictor cap is leaking air or maybe is too tight. If you had the top cover off, make sure that the tubes are routed right so as not to get pinched when the cover is put back on, the smart mix knob should be in the water setting and that the piston is on the bottom of the smart mix knob. Pump is bad. Try running a mix of vinegar and water to see if that unclogs the lines. Is the top cover and the base tight together in the back, sometimes the top breaks loose and it will raise up and it can’t spray, just re-fasten it down.
.
.Bissel’s Number is: 1-800-237-7691, they can tell you were to get service in your area.

I have the Bissell Proheat (7901) It will pick up water and the hand tool works fine. I noticed that the red indicator stopped spinning. Then I noticed no water was coming out. If I put down water using the hand tool, the vacunme will pick it up. When I called Bissell they had me do something with the indicator. When it didn’t work they said take it in for repair.
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101

I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
ANSWER :

Call BISSELL Consumer Services.
.

1-800-237-7691
.

Mon-Fri: 8am to 10pm ET
.

Sat: 9am to 8pm ET

My Bissell Pro Heat Pet will spray water but not pick it up when cleaning the carpet. Is there anything I can do to fix it? The furniture attachment hose picks up water well. It seems like it could be a bit more powerful of a draw on water. I don’t know it that has something to do with why the floor cleaning sucktion doesn’t work. Thank you for your time. Jenn
ANSWER : Normal. 0. . . . . . . MicrosoftInternetExplorer4. ...... /* Style Definitions */. table.MsoNormalTable.\011{mso-style-name:”Table Normal”;.\011mso-tstyle-rowband-size:0;.\011mso-tstyle-colband-size:0;.\011mso-style-noshow:yes;.\011mso-style-parent:””;.\011mso-padding-alt:0in 5.4pt 0in 5.4pt;.\011mso-para-margin:0in;.\011mso-para-margin-bottom:.0001pt;.\011mso-pagination:widow-orphan;.\011font-size:10.0pt;.\011font-family:”Times New Roman”;}....Hi,
.
.Here is a tip that will give you all the information you need to fix your Bissell.Proheat Vacuum Problem.
.
.Bissell Proheat Upright Wet/Dry Vacuum Problems
.
.heatman101

The water swirts ou put the vacuum does not pick up the water
ANSWER : Make sure that you are using the wet hose and that it’s not clog and hooked up tight to the hole in the front of the vacuum.The same place that you would hook it up to vacuum.