Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum\015 Bissell 12amps upright doess not want to spray water only shampoo does not spray water?\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

the internal hose may be kinked which will block the spray. try stretching out the hose. and giving it a few light tugs to release any kinks afterwards test to see if the machine sprays. if you still cannot get your deep clean essential to spray please visit Bissell comm to find the nearest Bissell authorized.
Turn off your machine and check to see if the brush window is secure. Make sure you are holding the trigger continuously while using the machine – this makes the front window light up. The spray tips under the brush roll window may be clogged on your machine. Use a pin to clear the spray tips.
Your Vax carpet cleaner may not be picking up water because the machine has picked up too much grime, and has become blocked up. Check around the head of the carpet cleaner for anything obvious that might make the suction on the Vax weaker, or look for clumps of hair that could be caught in the bristles.
A possible cause might be that the tank is not properly seated. To assure the tank is seated properly, pick it up and re-seat is so it sits snugly on the unit. If this doesn`t fix the problem, make sure the tank is assembled properly. To make sure they are both latched properly, pick the tank up by its handle.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
Your machine might not be fully primed. To prime the spinwave hold the spray button for 10 to 15 seconds to make sure the solution has flowed to the spray tips. You may not be holding down the spray button long enough, be sure you hold the button down until you have sprayed enough solution.
Can I use just water in Bissell CrossWave? Yes, you can use fresh water in the clean water tank, but it will mop floors better with a cleaning solution.
The water/solution tank valve may be stuck. Hold the water/solution tank over the sink and press the valve underneath to release. The water/solution tank is empty. Refill the tank.
A: Yes it can be used as a vacuum without water.
To reset, turn off and unplug, then plug back in and turn on. The brush roll may have lodged debris or other entanglements keeping the brush from rotating. To fix, you`ll need to remove the brush roll to inspect. First, make sure your vacuum is turned off.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

I have a Hoover Platinum carpet cleaner, and it has stopped dispensing cleaning agent and water. This model has a separate tank for water and separate tank for shampoo dispensing. It also has a power hand unit that dispenses shampoo. All along the hand unit has continued to dispense shampoo. Symptom #1, the water tank seemed to be taking on shampoo, as it was getting sudsy. Symptom #2 – On wash mode, nothing would come out, on Rinse mode, sudsy water would come out. Later, symptom #3 – not
ANSWER : Somewhere on the outlet is a control tap thats driven by a rubber band and something is up with this control ,best advice here is put it in the boot of the car and take iot to a hoover dealer ,they will do it seconds for you

I have a Bissel 9300-C 0714 BC Carpet Shampooer. It was working great and all of a sudden it stopped working. It still sucks up dirty water but it does not spray water onto the carpet. I can get it to spray water through the smallest hand attatchment but not through the large hand held piece on the base of the machine. I really hope you can help me, I am a dog groomer and I really need my machine to work properly. I can get it to spray water out of the smallest hand attatchment but
that’s all t
ANSWER : The spray jet has become clogged from the soap…. just clean it out. same thing happened to my attachment.

I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate
ANSWER : Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like it should. The big draw back to this model is Bissell has obsoleted all of its parts and most are no longer available. Might be wiser to buy new.

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.

Bissell will spray water when set to water rinse, but as soon as it is set to light, normal, or heavy cleaning, there is no spray. I have tried priming but to no avail. I put plain water in the solution tank to test without ay success. It is like it loses it’s prime whenever you try to use a solution mix. Once you set it back to water rinse only and go through the priming steps, it is OK. Any help would be appreciated. Thanks.
ANSWER :

Please check the following with liquid in both tanks.
.

.

– Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.
.

Check for debris on spray tips. Clean them with a soft brush (on old tooth brush works well). The spray tips may be lifted out for easier access.
.

– Ensure the tank lid is properly attached to the bottom of the tank. To attach this properly, remove the Water Tank from the machine. Hook the front window onto the lip of the bottom container and then allow the window with lid to cover the complete tank. Secure the latch on the back of the bottom tank to the back of the tank lid. THE TANK LID CANNOT BE ATTACHED PROPERLY IF THE BOTTOM TANK IS ALREADY INSTALLED IN THE MACHINE.
– Check the bottom of the Water Tank and the Formula Tank to make sure each has a red auto-load gasket attached. Make sure the Water Tank and the Formula Tank are seated properly. Depress the x on this gasket to ensure this depresses and release back out. Liquid from the tank should dispense.
.

– Remove the handle completely and re-attach. Once the handle is re-attached, re-attempt to spray.
.

.

If the machine continues to not spray, check the following:
.

REMOVE THE COLLECTION TANK:
• Make sure the unit is set to water rinse
• Remove the smart mix bottle and fill it with water only
• Place the smart mix bottle into the collection tank reservoir
• Run the unit and try to spray. If the machine sprays, you will be able to see the water level decreasing in the smart mix bottle and you will need to replace the bottom tank. It is possibly warped.
.

If these suggestions do not resolve your issue, contact BISSELL Consumer Services.
.

1-800-237-7691
Mon-Fri: 8am to 10pm ET
Sat: 9am to 8pm ET

Have a Bissell Proheat2 will not spray water from the carpet power head but sprays from tools setting Does anyone know how to get water to spray or clean out water
ANSWER : I had this problem. It was small pieces of debris that got into the solution lines and clogged all the nozzles. There is a nozzle for the handheld attachments, one on the front of the machine for spraying spots and two nozzles underneath just behind the rotating brushes.
.
.It was a royal pain disconnecting the clear rubber hoses inside the machine and blowing out the nozzles and the hoses with compressed air. If you are mechanically challenged I’d suggest you take the machine to a vacuum/steam cleaner repair facility.
.
.I’m not sure how the debris got into the solution system, but it may have been when the dirty water tank was emptied some of the dirty water entered the internal, clean water bladder.
.
.A note to Bissell engineers: This issue can be prevented if you simply add an easily accessable solution and/or water filter that the customers can remove, clean and reinstall. Just a suggestion.

Not wanting to spray shampoo/water piece of ****!!!!!!!
ANSWER : Capt. Obvious fixes: Of course make sure there’s clean water in the bladder of the water tank and soap in the soap tank, and make sure the dial is set to Floor Cleaning, not Tool Cleaning or somewhere in between.
.
.Sometimes an air pocket inside the machine (even a new one) keeps water from flowing, until you reprime the Bissell’s internal pumps. To prime the pumps the easy way, turn it on, then press, hold, and release the water-and-soap trigger a few times, waiting a few seconds each time.
.
.Still nothing? Prime it the slightly harder way. Separate the two water tank pieces. Only have the base tank filled and mounted on the Bissell without the piece that sits atop the tank. Turn it on. Kneeling on the floor in front of the Bissell, reach up and press the soap and water trigger at the top of the Bissell’s handle and hold it in as if you wanted water to go through. On top of the water tank is a plastic grommet hole about 1 inch in diameter, through which you pour water to fill the tank. Seal that hole with the flat of your hand. You’ll feel just a bit of suction. Lift your hand up and down a few times, a few seconds apart. Release the trigger and repeat a few times.
.
.Still no liquids? If your Bissell has been used at least a few times, particularly if you didn’t thoroughly clean the machine when finished, but after a year or so in a hard-water area like mine even if you are good about cleaning it, the water sprayers on your Bissell may have clogged with mineral deposits. This is a *fairly* easy thing to fix yourself, but please read all the way to the end and check out the GOTCHA before trying this.
.
.Unplug the Bissell. Remove the water tank pieces from the top of the base. You’ll probably reveal two red plastic pieces mounted in the Bissell’s base, about .75″ x .75″. These spray water on your roller brushes when you press the water-and-soap trigger at the top of the Bissell’s handle, and tend to clog with mineral deposits.
.
.Only work on one sprayer at a time so you can see how it goes back together.
.
.As you squeeze the red plastic sides of one red water sprayer, push up on the underside of the sprayer from underneath the bottom unit of the Bissell to release the sprayer from its mount in the base. Clean any lint or debris out of the mount area. Clean any gunk you can off the red water sprayer with an old toothbrush.
.
.Now you need to remove one water sprayer from the hose. You need a pair of pliers. Use the pliers to squeeze the brass colored clip that is keeping the red water sprayed mounted to the end of the small hose there. Move the clip up the hose so it compresses the spring and is no longer on the red plastic water sprayer. (See GOTCHA about the spring, below.)
.
.With the clip released, now you can twist and pull the red water sprayer out of the end of the hose. You’ll need a little hand strength to do this. Just be careful not to break the water sprayer by using a tool. They’re not particularly delicate, but breaking one would render your Bissell useless until it was replaced, so use a little care.
.
.When you’ve removed a red water sprayer from the hose, put the end of the red water sprayer that was inside the hose in your mouth and seal your lips around it, and try blowing through it. If you can’t blow air through it, it’s clogged. Open up a paper clip and push it back-and-forth through the small hole in the hose end of the water sprayer back towards its middle. You’ll probably push out a line of white mineral deposits. Clean them off the water sprayer with the old toothbrush, and try blowing through the water sprayer again. If air passes through clearly, you’ve fixed it. Push the water sprayer back on the end of the hose. Use the pliers to reposition the brass clip on the end of the hose over the water sprayer. Click the red water sprayer back into position in the base of the Bissell.
.
.Now do the same for the other red water sprayer.
.
.The GOTCHA: Once when I pulled one water sprayer off, the hose advanced up under the spring and I couldn’t reattach the red water sprayer, because it couldn’t reach the end of the hose. It’s best to use the brass clip or some other means (rubber band, tape, another clip) to keep the hose from crawling up inside the spring after you pull the red water sprayer off the hose. If the hose gets up under the spring anyway, despite your best efforts, fix this by removing the six screws on top of the Bissell base (this is the surface the water tank mounts on top of), and pry it up. Pull out the hose, reattach the red water sprayers on the hose, position the hose *very carefully* inside the base (there are mounts under there they need to fit into, so you don’t break anything), push the red water sprayers through the mount holes and mount them, and then reattach the screws to the base.
.
.You might want to prime the pumps again (instructions above). If the sprayers are clear, and the pumps are primed, but it still doesn’t get the floor wet when it should, the problem may be more serious. You may need a pump or motor inside the unit replaced.
.
.As you probably have learned the hard way, as I did, it’s VERY important to do a lot of cleaning of the Bissell after each use, more than the manual tells you to do. Clean the bottom of the unit. Thoroughly rinse out and empty both water tank pieces. Unscrew the three clear plastic pieces, one in front, two on the sides, that surround the brushes, and rinse them thoroughly in water. Clean off the brushes and all the lint and gunk around and above the brushes. (A water spray bottle and toothbrush are helpful here.) Tip the machine and get all the water out of the hole in the base. Release the red clip springs on the red water sprayers and blow on them. Doing this will slow the failure of the Bissell. It’s a great little machine for the money, but it does have a learning curve and needs more pampering than a vacuum cleaner, doesn’t it??
.
.Good luck!

NO WATER COMING OUT FOR SHAMPOOING /DUMPS WATER WHEN UPRIGHT
ANSWER : There is a belt inside that runs the pump to spray the water. I would take it in a have it replaced. Mine did the same exact thing.