Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum\015 How do I cure problem\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If your vacuum makes a popping noise along with a pungent burning smell, a motor failure may be the cause. This will involve replacing the main body of the vacuum, which contains the motor. For help replacing the motor, call the Dyson help support number at 1-866-693-9766.
Overheating due to clogged exhaust filter
The exhaust filter can also get clogged, causing a problem with the motor cooling. Therefore, you should also check the exhaust filter if the vacuum cleaner smells burnt. It is usually located on the top or back of the unit, right where the exhaust air comes out.
As the cleaner head and filter fills with dirt and debris over time, all the built-up debris begins to emit a burnt-smelling odour. You may need to remove and clean out the vacuum`s filter. We need to advise you to stop using your machine and request that you contact your local customer support team.
If there is a strong burning smell coming from the motor area of your Dyson DC14 or DC07 then it is most likely that your motor has burnt out.
A damp or musty smell is caused when dust in the cyclone has come into contact with water. It may not be a direct contact with water, for example when vacuuming pet hair that is slightly damp, this moisture will combine with the dust in the cyclone causing the smell.
Most Dyson vacuum have a built in safety system that stops the machine if it begins to overheat. This usually happens because the filters need washing or your machine is blocked.
Unfortunately, the higher the suction power of a cleaner, the louder the noise will be. The vibrating of the cleaner`s body – noise happens as air moves around inside the machine and hits various parts of the cleaner. This creates vibrations, which are the sounds you can hear.
A strong odor from the shellac that coats the copper coil windings is an indicator that the motor is about to or has burnt out. If the motor is still running, even if it turns on and off by itself as it is heating and cooling, you can still run the motor until it gives up for good.
The filter should be cleaned with cold water at least once every month. But you can clean it more often if you use the hoover more frequently, or if you gather up lots of dust and dirt from your home. And, once again, it should be completely dry before it is replaced in the V6.
Check the machine. A high pitch whistle could indicate a seal is damaged or the machine is blocked. If the noise occurs without the Wand and Cleaner head, it is likely to be caused by either the bin or cyclone.
The motor is failing, You will need to replace it and the hepa filter, Or when you put the new motor in the old hepa filter will be clogged up with the burnt smell and fibers from the old motor.
Put Dryer Sheets Inside The Bag
Place a dryer sheet into the dust bag of your vacuum cleaner before cleaning to improve the fragrance of the vacuum cleaner itself. In addition, you may use some orange peel or a few drops of essential oil on a piece of paper towel to remove the odor.
If there is something that has become caught in the hose in another part of the system, the airflow will be reduced and can cause overheating and a shut down. Clear out hoses, attachments, and brushes of any hair, dirt, and debris. This will allow for restored airflow and should get things going again.
To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on.
Vacuum cleaners are often designed to turn themselves off if they hit a thermal cut-off point. Basically, if the machine is starting to overheat, there is an automatic system in place to prevent damage to your vacuum or other issues. The most common cause of overheating is blockage.
If your vacuum cleaner keeps turning off, this could be due to the following reasons: Blockages – check the hose and head for any obstructions. Filter – always check your filters, if these are clogged this could be causing the vacuum cleaner to work harder and lose suction power.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
This means it is best to choose a vacuum cleaner with a noise output that is less than 70 dB. However, the noise levels of vacuum cleaners fall between 75dB to 85dB.
Belt is Broken or has Debris
The main reason why a vacuum may be emitting a smell of burning rubber is a broken belt or an object is suck. Excess hair or fur caught around the roller brush can also cause this issue. Turn off your vacuum and let it cool before doing anything.
One of the most accurate methods of vacuum leak detection is the helium leak detector. A sniffer is placed near the inlet to the vacuum pump to detect any increase in helium concentration in the air stream. Helium is then sprayed on any potential leak points in the system or piping.
We recommend replacing your air purifier filter every 12 months. That`s because over time, filters can get clogged with pollutants, and even let unpleasant odors back into the room.
`Get some pure peppermint oil and add a few drops on some paper towel, does a great job and is super cheap. `
Dyson purifiers capture 99.97% of allergens as small as 0.3 microns. A sealed HEPA filter captures particles as small as allergens and viruses, while activated carbon removes gases and odors.
If your vacuum runs but isn`t always picking up dirt, it might be time to change the belt. Consumer Reports` experts reveal how fast and simple it is to install a new belt which can save you a trip to the repair shop.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
ANSWER : The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal.
Read Full Q/A … : Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum
Hi folks,
my beam vacuum makes a very loud roaring noise quite often.
the problem started when i was vacuuming up a quantity of vermiculite from my chimney.
i think i overloaded the vacuum i think and it made this loud roaring noise.
the vacuum tends to make thos noise when i am hoovering after 5 minutes or so.
any ideas?.
thanks in advance Tom….
my beam vacuum makes a very loud roaring noise quite often.
the problem started when i was vacuuming up a quantity of vermiculite from my chimney.
i think i overloaded the vacuum i think and it made this loud roaring noise.
the vacuum tends to make thos noise when i am hoovering after 5 minutes or so.
any ideas?.
thanks in advance Tom….
ANSWER : If the filter bag is bad and didn’t trap all of the dust, then it got into your motor, so you may have a problem with your motor now.
Read Full Q/A … : Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum
I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
Read Full Q/A … : Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum
Burning Smell Hi, I have a Rainbow E series that when I run the vacuum there is a burning smell. I have cleaned the entire unit and filter but still have the smell? I am afraid that the motor will burn out?
ANSWER : Check the carbon motor brushes, there might be arcing on the armature. New brushes may help if the armature is ok.
Read Full Q/A … : Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum
Vacuum making high pitched noise and smells like motor is burning
ANSWER : Try repair first for quote and if too expensive then replace. 5 years is about the average life span.
Read Full Q/A … : Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum
Burning Smell coming from the moter
ANSWER : This could be a motor problem. There is always a slight blue arcing that occurs when an electrical motor runs and can be visible through the exhaust vent, but any excessive arcing indicates a problem. If the carbon brushes are sticking, this will cause excessive arcing and can be corrected by an experience service person, but if there is any electrical failure, the motor would have to be replaced. There are no parts available for these motors and the expense of replacing an armature (the likely culprit) would be more than the motor. This could also be as simple as a worn belt, but usually, belts will not produce the smell your describing. When a motor is burning out, it will produce an acrid odor that will linger for a long time.
Read Full Q/A … : Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum
Bissell lift off pet revolution vacuum smells bad when I vacuum!
ANSWER : Put a BOUNCE sheet inside the filter
Read Full Q/A … : Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum
