Oreck XL Shield Power Scrubber Floor And Carpet Cleaner\015 The motor went high pitched and stopped sucking up water\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

This motor filter is located at the back of the powerhead in the Oreck
A carpet cleaner is a device that mechanically applies soap and water to a carpet from a clean water tank, scrubs, and then suctions up the byproduct into a dirty water tank. Carpet cleaners work by applying and suctioning up water.
Clog located in the vacuum hose

Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.

Avoid using beater heads and brushes – they will catch and lift the fibres, and eventually this will give your carpet a bobbled or felted appearance. Cut pile carpets should ideally be vacuumed with an upright vacuum cleaner with a beater bar and brush.
To clean a foam filter, submerge it in water, squeeze it to allow the dirt to escape the foam, and allow it to air dry before putting it back in your vacuum. If you want the room to smell really nice next time you`re vacuuming, add a few drops of essential oil to the foam.
The Oreck family sold their vacuum cleaner business to private equity investors in 2003, initially American Securities Capital Partners. Ten years later, following Chapter 11 bankruptcy it was purchased by Techtronic Industries.
First, check to make sure the clean tank has water and/or the water & formula mixture in the tank. If your tank is empty, this could be the reason your machine is not spraying. You will need to fill your clean tank again. Reseat the tank and ensure it sits snug on the machine.
Inspect the vacuum hose for any small holes, kinks, or cracks. Any cracks or holes will decrease the amount of suction in the hose and will not allow the carpet extractor to properly remove liquid from the floor. The hose will need to be replaced if there is damage.
It`s really straightforward – all you need to do is sprinkle a generous among of baking soda over your wet carpet and let it sit. The baking soda not only absorbs moisture, but it`ll also absorb any nasty odours.
Your carpet will be only slightly damp to the touch after your cleaning. Most carpets typically need 6-10 hours to dry completely. However, it could take up to 24 hours to dry depending on the time of year your carpets are cleaned, and the air circulation, humidity and temperature in your home.
Vacuum cleaners are fairly simple machines. They need power to be transmitted to the vacuum to create a suction force that lifts debris. So, the usual areas that cause suction loss include the wrong height setting, stuck rollers, a faulty gasket, a broken vacuum belt, a filled bag, or a clogged hose.
Troubleshooting your vacuum cleaner`s loss of suction

1) Clogged air filter – As noted above, vacuum cleaners may use one or more air filters to trap dust and dirt as the air travels through the product. The filters can become clogged over weeks of use, reducing the vacuum cleaner`s suction.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.

Water is not being discharged. I have filled the reservoir that holds the carpet cleaner fluid And I have filled the water container. I know how to use the cleaner, it has always worked, But now, no water is being discharged to the carpet. I turn it on, squeeze the trigger, but nothing comes out. The wheel that is suppose to spin (to indicate that water is being discharged) is not spinning. Everything else works. I.e. the suction works, and the hand held accessories work.
ANSWER : That means that the pump belt is worn and it needs to be replaced. You can get a replacement belt and view the manual here:

Bissell Pump Belt

My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there’s a little thingy that should be spinning or turning….. When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI – I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn’t wet. Any tips? The manual doesn’t help.
ANSWER : You need to replace the pump belt. Here is the belt you need:

Bissell ProHeat Belt

I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
ANSWER :

Call BISSELL Consumer Services.
.

1-800-237-7691
.

Mon-Fri: 8am to 10pm ET
.

Sat: 9am to 8pm ET

I have the Bissell 2x proheat. There is no water being sucked up from the bladder and the cleaning solution is not being sucked in either in order to get to the carpet. On water rinse the carpet gets wet but I’m not seeing any water going through the clear front piece. I live in Harvest Alabama. Where can I take it to get fixed if it needs it?
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 .
.retqwe

I have a Bissel 9300-C 0714 BC Carpet Shampooer. It was working great and all of a sudden it stopped working. It still sucks up dirty water but it does not spray water onto the carpet. I can get it to spray water through the smallest hand attatchment but not through the large hand held piece on the base of the machine. I really hope you can help me, I am a dog groomer and I really need my machine to work properly. I can get it to spray water out of the smallest hand attatchment but
that’s all t
ANSWER : The spray jet has become clogged from the soap…. just clean it out. same thing happened to my attachment.

Bissell ProHeat 2x Upright Carpet cleaner-water tank valve
ANSWER : Www.usavacuum.com/category-s/387.htm

You can find the parts you need here

I have a Bissel proheat 7901 carpet cleaner and it is not sucking the water up. Normally when I clean the water gets sucked back up and I have to empty the dirty tank. Now no water is in the tank when I am done cleaning. Please help I cannot afford to take it to the shop.
ANSWER : I’m not sure if this will help but I had the same problem and was about ready to pull my hair out. I ended up taking the fill tank off and if you look inside where the red overflow flap is you will find a small screened opening. I found that mine was pretty clogged up with debris but once I removed the mess and put my machine back together it is now sucking like a champ. I hope this helps. Here’s hoping that you don’t have the pay for a service person to look at it.