Kenmore 25512/ 25513 Progressive Canister Vacuum\015 Tried to take the power head apart by removing the 3 screws on the one side of the power head. Was not able to pull the sections apart and since they are plastic was worried something would break with continued prying. Need help with how to repair the power head connection and, probably, how to disassemble the power head.\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

A damaged vacuum hose, clogged motor air filter or bad suction motor can cause the vacuum cleaner to shut off during use. A tripped overload on the vacuum suction motor can shut off the vacuum cleaner during use. If your vacuum has a reset button, push it; if the vacuum seems hot, let it cool off first.
If the brushroll is sticking, it will cause too much friction and put too much strain on the belt. Remove the brushroll and clean all hair, string, and lint from the brushroll bearings. If the vacuum cleaner brush still doesn`t spin after you clean the brushroll, consider replacing the brushroll.
Check service panel for tripped breakers/blown fuses. If breaker is tripped, reset it. If fuse is blown, replace it. If vacuum cleaner is plugged in, be sure power button is in the off position before resetting breaker/changing fuse.
Besides getting jammed with dirt and debris, the major problem that cordless vacuums face is a weak battery or failing recharger. Some cordless vacuum batteries are easily replaced while others are not and require that the entire unit be replaced.
Overheated Motor

If your vacuum was working fine and then suddenly shut off, it may have overheated. Most vacuums are equipped with a thermal protector safety switch that won`t allow the motor to run when it becomes overheated. You will need to wait for 30 minutes to 2 hours, depending on your machine, to try again.

If your roller is not spinning, the first step is to remove the roller and free any debris. Refer to your model`s user manual on how to remove the roller from your vacuum head. Debris can also be left on the vacuum head it is important to also clean this area including the sides where the roller brush connects.
Check for a plugged hose:

Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.

How long do Kenmore vacuums last? A. It`s suggested that the typical vacuum can last up to an average of eight years. With proper maintenance, a Kenmore vacuum could last that long or longer.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
If your Shark ION Robot R75 vacuum stops moving unexpectedly after a few minutes of normal movement, it may simply have low battery power. Check that the device is powered on and that the battery has a significant charge.
Why does my Shark vacuum keep stopping? For Shark robotic models, odd sweeping or sudden stops can often be a result of dirty vacuum sensors. These sensors can often be found on the bottom and sides of the vacuum. Hitting them with a soft cloth should be enough to remove any excess dirt.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
Low suction or poor pick-up may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action, check for clogs. First, remove the Easy Empty dirt tank from the vacuum and discard all dirt and debris.
If you don`t vacuum your carpet, the dirt will break down carpet fibers and create a breeding ground for dust mites and bacteria. In addition, your home will begin to smell musty from the dirt, mites, and other organisms settling into the fibers.
Some vacuums have an in-line thermal fuse (often located between the switch lead and the motor coil). If the fuse is blown it will need to be replaced. – Check your home circuit breaker – it may have tripped. – Some vacuums have a brushroll on/off control.
Putting in the incorrect amount of oil, putting in the wrong type of oil, and oil contamination can all cause the pump to not reach full vacuum. For this reason, you must check the oil regularly to ensure that it is not only clean, but also properly filled.
If you checked your brush roll, floor setting, and belt but your brush roll is still not spinning, that means you probably need a Shark micro switch replacement. This small switch tells the vacuums brush when to start spinning.
If the roller brush is not spinning, it cannot pick up dust. One reason could be that the power button is not set to position II, which runs the roller brush. If the button does not work, here is the link to the power button replacement guide. Another reason is that the roller brush could be broken.
Almost every time that the brush stops turning, it is because of hair wrapped around the brush roller. You will burn out the belt if you use it too long in this mode. Your only fix is to take it apart and and clean it (and cut any hair stuck in it in the process).
1. Motorized Brush Head. Sometimes called the “power nozzle,” this large attachment has a rotating brush to clean carpets more like an upright.
Discovering the advantages of the on/off brush roll

When vacuuming hard surfaces, the brush roll can often push dust and debris away from the vacuum before it can be suctioned. Turning off the brush roll switches the vacuum to “suction-only” for quick and easy cleaning of hard floors.

A Revolving Brush Roll Greatly Enhances Carpet Cleaning

These brush rolls revolve at a very high speed, agitating the carpet fibers in the process. The effect of this is to loosen dirt and move it toward the top, aiding in its removal from the carpet fibers.

One caveat: Handling this vacuum`s 23 pounds takes some muscle. In our member survey, Kenmore canisters earned a very good score for predicted reliability and an average rating for owner satisfaction.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections:
1 at the handle / upper wand
1 at the lower wand top of the power brush attachment

I replaced the entire wand assembly and it worked great for a year or so and now it’s doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

ANSWER : This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it is plugged in together.

When connecting the wand into the brush component. sporatic power (sometimes runs sometime nothing) the power is on again off again. when hold pressure down on the wand the power stays on. do you think the coupling connection is bad on the wand? would the wand replacement likely be the culprit?
ANSWER : There is is switch or sensor in the connection. Likely that piece is worn or shorted out. You may be better off getting a new wand piece

Power head and wand connection is intermittent.
ANSWER : If there is a rubber bumper on your power head you must slip it off before the two halves will separate.

Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head.
Is there anything else I can try? Model Callisto
ANSWER : Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor.

Keep in mind this is repairable, and if the unit is less than 5 years old it should still be under warranty.

Good luck .

Power head does not activate
ANSWER : Have you pushed the rest switch on the top housing? It may be on the side?

Power to power carpet head
ANSWER : Once again remove the electrical connections and clean it and also blow the dirt and then fit it tightly and carefully.if anything broken inside replace it.

Our Electrolux canister vacuum just stopped working when we were vacuuming the floor. The power does come on when the power head is attached but as soon as the power head is removed the power shuts off. I tried pressing the reset button but that doesn’t help. Is there a solution that I can try at home?
ANSWER : Sound like you problem is in the connection going to the power head you will see a small screw on the power nozzel where it joins to the handle take out the screw and take it a part you will see where one of the bars have been disconnect from the power.

The motor on my Epic 6500 works, the hose is sucking, but the power head isn;t working… I tried the sidestep power head and that one works. Ive opened and replaced the belt and that is fine. The bulb was already burned out and wasn’t replaced so I cant tell if theres power to the head. What else could it be?
ANSWER : Connect the power nozzle directly to the hose and try.
.Check the terminals where the wand connects to the PN. If any are discolored or cracked, that may be the problem.
.Open the PN and check for loose or broken wires and connections. Repair or replace as necessary.
.The reset switch could be broken or worn out. You can check this with a continuity tester or multimeter.
.If none of these solve the problem the vacuum needs to be taken to your local Aerus Electrolux store for diagnosis and repair.
.
.http://www.aerushome.com/storelocator/