ProHeat Turbo Deep Cleaner Upright Steam Vacuum: Hello, My Bissell Proheat is not spraying water, …

ANSWER : Most likely the pump belt is worn and needs to be replaced. Here is the belt you need:

Bissell Proheat Pump Belt

ANSWER : Try adding a table spoon of salt to the water.

ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101.
..mn.,b

ANSWER : Hi, this is very common problem the problem is that the problem is a simple one but solving it can take time. The problem you have got is that the detergent has turned to a gel over time and caused a blockage somewhere in the system now the problem you have is finding it as it can be anywhere from the detergent bottle down to where it comes out. The first thing to try would be to use very hot not boiling water put this into the detergent bottle without detergent then wait a few minutes then keep trying it for another couple of minutes if after doing this you still have the problem then its going to be a case of getting your tool box out( That is if you know more or less what you are going to do and remember how it goes back together, they are not difficult) if its still blocked then you need to start where the detergent comes out by removing the panel at bottom of the vac should be held on by 3 or 4 screws once this is off you should be able to see the jets where the mixture comes out (check these are not blocked use pin to push any muck out of the way) Once you have undone these screws you will need to puul the rubber hose off the jets but make sure you dont break it as getting parts can be a night mare. Now you need to keep working backwords up till you get to the detergent bottle along the way their will be a blockage. The problem is their are no manuals showing you how to do this and as all makes and models are different its difficult for me to give you exact instructions but if you have some knowledge of how things work then you should have no problems removing a few parts and giving them a good clean. Please try using hot water a few time first as this can solve the problem but you might need to do it 5 or 6 times without detergent hopefully this will solve your problem. Now what they should have told you when you brought this but they dont tell you and it doesnt tell you in the user guide is: After every use empty out any detergent and then run clean warm water through the vac for at least 5 minutes doing this ensures that the detergent wont turn to a gel with it sitting around. Doing this will ensure it will keep working and wont need taking apart after every use. (Why they dont tell you this in user guide is absolutely stupid as doing this will ensure you can keep using it over and over again). The problem you are having is the same problem that everybody has with this type of cleaner everybody who buys one has this same problem so dont think it is just you, its something they should explain to customers when they buy these but as usual they are only interested in your money. Let me know how you get on or if you need further assistance ok

ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 . ..,/

ANSWER : Please check the following with liquid in both tanks..

.

– Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.
.

– Check for debris on spray tips. Clean them with a soft brush (on old tooth brush works well). The spray tips may be lifted out for easier access.
.

– Ensure the tank lid is properly attached to the bottom of the tank. To attach this properly, remove the Water Tank from the machine. Hook the front window onto the lip of the bottom container and then allow the window with lid to cover the complete tank. Secure the latch on the back of the bottom tank to the back of the tank lid. THE TANK LID CANNOT BE ATTACHED PROPERLY IF THE BOTTOM TANK IS ALREADY INSTALLED IN THE MACHINE.
– Check the bottom of the Water Tank and the Formula Tank to make sure each has a red auto-load gasket attached. Make sure the Water Tank and the Formula Tank are seated properly. Depress the x on this gasket to ensure this depresses and release back out. Liquid from the tank should dispense.
.

– Remove the handle completely and re-attach. Once the handle is re-attached, re-attempt to spray.
.

.

If the machine continues to not spray, check the following:
.

REMOVE THE COLLECTION TANK:
• Make sure the unit is set to water rinse
• Remove the smart mix bottle and fill it with water only
• Place the smart mix bottle into the collection tank reservoir
• Run the unit and try to spray. If the machine sprays, you will be able to see the water level decreasing in the smart mix bottle and you will need to replace the bottom tank. It is possibly warped.
.