Bissell 7950 ProHeat Upright Wet/Dry Vacuum\015 Replaced belt and motor shaft spins but wont turn pump shaft\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If brush will not turn by hand, or belt is broken, replace the damaged part by ordering online at BISSELL.com. Clean off any debris on the brush. If the brush is still not turning, please take the unit to an Authorized Service Center to have a Quality Technician inspect the unit.
Make sure the power cord and the plug are not damaged. If either are, contact our Consumer Care team. Make sure the outlet works by plugging in a cell phone charger or small appliance. If it doesn`t work, check another outlet.
You may have stalled the brush motor. To reset, turn off and unplug, then plug back in and turn on. The brush roll may have lodged debris or other entanglements keeping the brush from rotating.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
Unplug and check to see if your clean tank is seated properly. Also, remove the dirty water tank and make sure there are no clogs in the hose below it. Remove the filter and clean both the screen and filter of any build up or debris and empty the tank before replacing it.
Unplug your machine to reset the brush. While unplugged, remove the brush window and brush roll from your machine, by pulling the tab. Take out the obstruction that was causing the machine to stop working. Once the obstruction is removed, you may reassemble the brush roll and brush window.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
The brushes on the Hoover All Terrain Steamvac won’t turn. However, when I try to turn them manually they will turn. So, why won’t they turn when the machine is turned on?
ANSWER : Some vaccums have a belt on the brushes. might need a new one if it does have the belt
Read Full Q/A … : Bissell 7950 ProHeat Upright Wet/Dry Vacuum
Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle
the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) – no dirt or blockage is apparent (it is a very simple device with 1 moving part
wires to the pump also pass a continuity check
THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the “manual” cleaning mode – a
ANSWER : You can contact Bissell directly at the following
.
.For UK inquiries:
.Monday – Thursday 9 am — 5 pm
.Friday 9 am — 4 pm
.
.BISSELL Homecare (Overseas) Inc.
.The Boat Yard
.105 Straight Road
.Old Windsor
.Berkshire, SL4 2SE
.United Kingdom
.Telephone: 0870-225-0109
.
.
.For Australian inquiries:
.24 hours a day 7, days a week
.E.D. Oates Pty Ltd
.76 – 82 Newlands Road
.Reservoir VIC 3073
.Australia
.Telephone: 1-800-811-183
.
.
.For all other inquiries:
.Monday – Friday 8 am — 4 pm
.BISSELL Homecare, Inc.
.PO Box 1888
.Grand Rapids, MI 49501 USA
.Telephone: 01-616-453-4451
.Fax: 01-616-453-1383
.
.You can get Bissel Spares that the following
.
.http://www.4bissell.co.uk/cgi-bin/pne.pl?display=entry&brand_id=454&f-10=
.
.For UK inquiries:
.Monday – Thursday 9 am — 5 pm
.Friday 9 am — 4 pm
.
.BISSELL Homecare (Overseas) Inc.
.The Boat Yard
.105 Straight Road
.Old Windsor
.Berkshire, SL4 2SE
.United Kingdom
.Telephone: 0870-225-0109
.
.
.For Australian inquiries:
.24 hours a day 7, days a week
.E.D. Oates Pty Ltd
.76 – 82 Newlands Road
.Reservoir VIC 3073
.Australia
.Telephone: 1-800-811-183
.
.
.For all other inquiries:
.Monday – Friday 8 am — 4 pm
.BISSELL Homecare, Inc.
.PO Box 1888
.Grand Rapids, MI 49501 USA
.Telephone: 01-616-453-4451
.Fax: 01-616-453-1383
.
.You can get Bissel Spares that the following
.
.http://www.4bissell.co.uk/cgi-bin/pne.pl?display=entry&brand_id=454&f-10=
Read Full Q/A … : Bissell 7950 ProHeat Upright Wet/Dry Vacuum
No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I
ANSWER : Search for bissell pro heat pump. bissell.com will not have it
Read Full Q/A … : Bissell 7950 ProHeat Upright Wet/Dry Vacuum
No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I
ANSWER : Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. If you were the the heater is plugged and won’t allow water to spray out the bottom.
.
.
.
.
Read Full Q/A … : Bissell 7950 ProHeat Upright Wet/Dry Vacuum
Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there’s two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it’s a ribbed belt? that is the water pump belt?
ANSWER : Just taken ours apart with the same problem… found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places – the bottom of the screw wells..This means that the water tank cannot exert sufficient pressure on the valve to release the water..Only solution is a new top cover assembly
Read Full Q/A … : Bissell 7950 ProHeat Upright Wet/Dry Vacuum
The Vaccum is not turning on when i plug the hose into the wall. The hoover system will turn on when i turn the switch on at the base and wont go off till i turn the switch off. But it will not come on automatically when i put the hose in to the wall connections.
Many Thanks
Linda
Many Thanks
Linda
ANSWER : You can test this out by taking a small metal spoon and with the bottom side of the spoon insert it into the vac outlet on the wall. you want to touch the two metal pins inside the vac outlet to test if the unit is the problem or the hose is the problem.
.
.If the unit starts, the hose should have a 3 year warranty on it. I recommend you have your nearest beam dealer check it out.
.
.If the unit does not start, it has a 7 or 10 year warranty, the circuitry should be replaced. Again have your nearest beam dealer check it out.
.
.good luck
.
.If the unit starts, the hose should have a 3 year warranty on it. I recommend you have your nearest beam dealer check it out.
.
.If the unit does not start, it has a 7 or 10 year warranty, the circuitry should be replaced. Again have your nearest beam dealer check it out.
.
.good luck
Read Full Q/A … : Bissell 7950 ProHeat Upright Wet/Dry Vacuum
Shark Euro pro mop the ligt wont turn on anymore.
ANSWER : My husband fixed my shark steamer by taking it apart and testing it wire by wire .the problem ?a fuse hidden inside the unit..unscrew the screws and get inside the steamer .at the bottom of the steamer there is a gold orange foil looking piece .under that is a small fuse .unless you can find another fuse just cut that one off and rewire the wires together .shark now comes on
Read Full Q/A … : Bissell 7950 ProHeat Upright Wet/Dry Vacuum
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would “heave” (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won’t turn. Any suggestio
ANSWER : Carpet brush won’t turn when vac on
Read Full Q/A … : Bissell 7950 ProHeat Upright Wet/Dry Vacuum
