Vacuums

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

The most common problem with a vacuum cleaner is also the easiest to remedy: clogs in the hose or attachments. Also the electrical cord, motor, switch, fan, brushes, and motor bearings can all need repair or replacement. The drive belt may need replacing; and the attachments, hoses, and filters may need unclogging.
To release the wand on the Hoover® REACT™ Powered Reach™ Plus press the Powered Reach™ Mode button on the top of the canister. This will allow you to remove the canister and access the wand release. The wand release button is located on the spine of the vacuum directly behind the dirt cup.
There are varying degrees of quality and value when it comes to vacuums; if you paid a lot for the appliance, repairs are likely worth it, but we recommend that you don`t spend more than half of the original price for any repairs.
The average life expectancy of a mid-range vacuum cleaner is about six years. You can fix or replace things like blocked filters, jammed brush rolls, frayed hoses, worn-out stick vac batteries and broken accessories yourself.
As a general rule, if the repair is going to cost less than half the cost of a new vacuum cleaner, it`s best to go ahead and get it repaired. When the service tops half the price of a new machine, it`s probably best to invest in a newer model.
How Vacuum Switches Work. Once the switch registers a change in the negative pressure based on the preset sensitivity of the setpoint, the diaphragm of the switch will open or close the attached circuit, turning off or powering on a device. Vacuum switches can be used with NO and NC states.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
Fine particles. Fine particles are no match for even the strongest vacuums. Construction dust, makeup, used coffee grounds, fireplace ash, and other fine particles can burn out the motor and be released back into the air. It`s best to sweep these items up to keep your vacuum – and yourself – safe.
Your vacuum cleaner will stay in excellent working condition if you have it serviced regularly. A regular service will also help the motor to last longer and prevent it from breaking down prematurely.
“We would recommend vacuuming at least once or twice a week—and more often if we have pets—with the right tools to remove dust quickly and effectively,” Patel advises.
A vacuum cleaner gets power from a regular electrical socket, with the average upright design requiring between 450 and 3000 watts. However, the most often used versions use around 1400 watts, equivalent to approximately 1.4 kilowatt-hours (kWh) of electricity each hour.
This is unlikely to ruin a vacuum cleaner completely; however, it can still create a mess within your bag or vacuum chamber. You`ll probably need to let it dry out before using the vacuum.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
A washable HEPA filter should be cleaned by rinsing it under cold water. You should be careful not to touch the filter material, only allowing it to come in contact with water. Allow the filter to completely dry before reinstalling it.
For best results the filters can be washed in warm water but check they are thoroughly dry before putting them back into place, this may take up to 24 hours. Hoover recommend that you fit new filters once per year to keep your vacuum cleaner in tip top working order.
An extension wand extends the reach of crevice and dusting tools to clean areas such as ceilings and high corners.
Central vacuum wands are the extension pieces either metal or made of ABS plastics that connect the handle of your central vacuum hose to your cleaning attachments. On this page, you can choose wands to fit your central vacuum hose.
Vacuum switches can have an electro-mechanical or solid-state switch construction.
Simply plug the product back in or restore the power and then switch off the appliance using the button on the control panel. The door will now unlock.
How does a vacuum breaker stop backflow? The pressure of flowing water pushes the valve open. When the water is turned off, the pressure decreases and the valve closes. The air pressure keeps water from seeping back into the spigot from the outside.
In order to actuate the switch, the diaphragm needs to be pushed against the switching mechanism. So it all comes down to this. Air is either pushing the diaphragm up, or sucking it up. That is the difference between a pressure switch and vacuum switch.
To release the wand on the Hoover® REACT™ Powered Reach™ Plus press the Powered Reach™ Mode button on the top of the canister. This will allow you to remove the canister and access the wand release. The wand release button is located on the spine of the vacuum directly behind the dirt cup.
The Dyson vs. Kirby vacuum cleaners debate can be complicated, as these brands are so different. If it comes down to price or size, Dyson will probably get the upper hand — but for all other vacuuming considerations, Kirby is the way to go.
Kirby vacuum prices are higher than many vacuums found at big-box stores, but that`s because Kirby vacuums are made of durable materials that will last for years. Why replace an inexpensive vacuum over and over again when you can purchase a Kirby vacuum? This complete home cleaning system that will last for a lifetime.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Remove & replace handle release lever on hoover model U6445, s/n 039900015686
ANSWER : From under the vacuum, there is a tab release that you need to pry out the old part. At this point, based on your serial nuimber, your vac is over 10 years old and may also need the base. The bracket is part of the base and not expensive, but the replacement is involved. Once the vac is disassembled, other things may need to be replaced.

Read Full Q/A … : Vacuums

The handle release lever (Part N. 38434-021) on my Hoover WindTunnel upright vacuum (uses Y bags) broke. How do I install the replacement release lever (pedal) that I purchased?
ANSWER : You can buy Hoover Handle Release Lever 38434-021 at
.http://partsreadyonline.com/item.php?ItemID=798

Read Full Q/A … : Vacuums

How do you remove the Handle from the Hoover Windtunnel Deluxe to replace the switch?
ANSWER : Removing the handle assembly should be easy after removal of the two screws. It may be binding or hanging up on the self-propel cable…or the plastic may just be stuck/binding. Note that the handle slides in and out of the vacuum unit along the same axis as the two screws (i.e. slides straight off the back towards you when you are standing behind the vacuum). Try to pry it off gently w/thin-bladed screwdriver or butter knife (careful now!). Not sure about the smoking issue but you may have a severely plugged filter and the unit is overheating as a result. Check that out immediately/first to avoid fire or expensive motor burnout.

Read Full Q/A … : Vacuums

Hoover Wind Tunnel U6458-900
Self Propel doesn’t work – via other expert advice here for other models of Hoover – I’m thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is – I can’t get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac
ANSWER : On some models there are hook/springs that hold the cover of the base snug.

Read Full Q/A … : Vacuums

Hello, I have a Hoover quadraflex Powermatic central vacuum system Model # s8099-031 that requires a new replacement 35 ft hose…I have contacted Hoover and they do not know where to buy a replacement hose for this model. I live in Canada. Any idea where I can get a replacement hose for this system? Thanks kindly, Tammy
ANSWER : Tammy, no info re your location, so I”l try this.
Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover head by changing the upper steel tube.
Find a Hoover service center, outlet in the yellow pages and ask for the “NEW “style, gray“Plastiflex“ brand hose and upper adapter tube sold with new Hoovers at Costco and you will be all set. Then, when the head eventually dies, you can upgrade to a far better one , while still having the Hoover cannister, the hose and tools do not need to match the original tank.

Read Full Q/A … : Vacuums

How do you replace Hoover Handle Release Pedal on
ANSWER : The handle pedal is snapped in to the base, where it pivots.
.The pedal needs to be pried away fron the base, exposing the pivot pin to release it for removal. On your model, you will likelly have to remove the lower handle from the base (where it pivots) to get room to release and replace the pedal.

Read Full Q/A … : Vacuums

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks
ANSWER : If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out.

Read Full Q/A … : Vacuums

Need to replace the handle-release lever on a Hoover model U8125-960 Vacuum cleaner
ANSWER : The exploded views at this URL will help you identify the part and you will be able to order it as well..
.http://www.ereplacementparts.com/hoover-u8125960-savy-bagged-and-bagless-vacuum-parts-c-37315_37337_37538.html

Read Full Q/A … : Vacuums