Dyson DC07 Bagless Upright Cyclonic Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Dyson Belts, Fits: All Upright Vacuum Cleaner Models Using one Belt System, 3 Belts in Pack.
If your agitator brush roll on your Dyson DC07 isn`t turning correctly even though the motor runs smoothly, a snapped or worn out drive belt may be causing trouble. If the drive belt in your vacuum cleaner has either perished or damaged, don`t fret it`s fairly simple to replace.
The Dyson DC07 was introduced in 2001 with brand new Root Cyclone technology.
The DC07 had a long production run from 2001 until 2008, and came in many different colour combinations.
Because vacuum manufacturers do not share a standardized naming system for vacuum belts, using your vacuum`s model number is the best way to ensure an accurate belt order.
Vacuum belts work to spin a vacuum`s brush roller and/or, on some self-propelled models, to turn a vacuum`s wheels. Whatever the style of vacuum, this repair will take placein the machine`s brushroll area.
If your vacuum runs but isn`t always picking up dirt, it might be time to change the belt. Consumer Reports` experts reveal how fast and simple it is to install a new belt which can save you a trip to the repair shop.
Next to the motor, the belt on your vacuum is just about the most important part of your vacuum. Without the belt to spin the brushroll, most vacuums won`t pick up on carpeting at all! If your vacuum uses a rubber belt, check it once a month for cracks, melting, and especially, slippage.
You should replace the belts on your vacuum at least every three to six months if the vacuum is regularly used. This is very important for proper cleaning.
Dyson DC07™ Upright vacuum cleaner (Clutchless)
The Dyson DC07 Animal has been designed specifically with pet owners in mind. It comes complete with a HEPA filter, a 3.5 litre bag capacity and a clutch that makes it perfect for all floor types.
Dyson was designed and patented by a British, had it made in Malaysia (Johor Bahru), – as it is cheaper to make here.
To recycle your old machine, you can bring it in to a Dyson Demo store or Dyson Demo Zone within 28 days of purchase of your new Dyson machine, show us the receipt or order confirmation email, and it can be recycled free of charge.
Most Belts are normally measured from where the belt leather folds at the buckle end to the middle hole at the tip end and are usually stamped on the back of the belt with the size example 32, 34, 36 etc.
The optimal length of the gun belt is determined by looking at your waist size plus how you carry. You typically want to wear a belt that measures four inches longer than your normal pant size. For example, if you normally wear size 38-inch pants, you may want a 42-inch belt.
There are three common V belt types: Classical V-belt (classified by their dimensions from A to E), Narrow V series (ranked by their sizes 3V, 5V, and 8V), and light-duty Fractional Horsepower belt (classified by their dimensions 2L, 3L, 4L, 5L).
Look for a control knob on the front right hand side of your Dyson vacuum. If your machine has a knob it is a clutched model. If your machine does not have a knob it is a non-clutched model.
Do not use any detergents, polishes or air fresheners to clean the bin. Do not put the bin in the dishwasher. Clean the cyclone shroud with the brush on the combination tool to remove lint and dust. Do not immerse the whole cyclone unit in water or pour water into the cyclones.
While some machines use one HEPA filter, most Dyson vacuums use two filters; the pre-motor filter and the post-motor filter.
We recommend replacing your air purifier filter every 12 months. That`s because over time, filters can get clogged with pollutants, and even let unpleasant odors back into the room.
How frequently does your air purifier need an air filter replacement? It`s recommended that you change your filter every 12 months.
Since you`ll likely only replace your serpentine belt once during the life of your car, it`s generally recommended to take your car to a professional mechanic. You can do a lot of damage to your vehicle if you drive on the road with an improperly installed serpentine belt.
Introduction: Duct Tape Vaccuum Belt
Have you ever broken a belt on your vaccuum and didn`t have a chance to buy a new one? You can make your own out of duct tape for a TEMPORARY fix. This belt is for TEMPORARY USE ONLY, you might damage your vaccuum if you overuse this belt.
Yes. The car is propelled by the engine through the transmission. The absence of drive belt won`t stop a car from moving from its stationary position but it will affect the operation of the engine which will cause it not to operate for long.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
ANSWER : The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Replace belt for dyson upright – Dyson DC07 Bagless Upright Cyclonic Vacuum
ANSWER : DC07s have two belts – one connects the output of the motor to the clutch, the other connects the clutch to the brush bar.
I suspect the belt
you are to refering to is the one from the clutch to the brush bar. Unfortuenately the other belt is hidden under a plastic cover, so you cant see if it is okay or not without some dismantling. This cover is not easy to remove and requires a Torx driver to under the securing screws.
Have a look at www.dysonmedic.com, but unless you have access to such a tool, probably time to call Dyson or a Vacuum repairer.
I suspect the belt
you are to refering to is the one from the clutch to the brush bar. Unfortuenately the other belt is hidden under a plastic cover, so you cant see if it is okay or not without some dismantling. This cover is not easy to remove and requires a Torx driver to under the securing screws.Have a look at www.dysonmedic.com, but unless you have access to such a tool, probably time to call Dyson or a Vacuum repairer.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
How to put new cable on dyson dc07 upright – Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
ANSWER : Have a look at www.dysonmedic.com which has some excellent info on your machine.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Replace belt on dyson animal – Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
ANSWER :
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
How do you change a belt on a dyson DC07 – Dyson DC07 Bagless Upright Cyclonic Vacuum
ANSWER : Turn vacuum over so you can see the brush.
.Using a standard screwdriver, undo the three fasteners just behind the brush.
.Remove the base plate.
.Remove the belt.
.Remove roller brush.
.Place new belt on roller brush and center it in position.
.Feed belt through the hole, and return brush to position.
.Ensure the brush ends are located in the slots correctly.
.Pull the belt over the motor shaft.
.Rotate the brush a few times to ensure belt is centered and secure.
.Replace the base plate, tighten fasteners, and rotate the brush a few more times to make sure it turns properly and the belt isn’t caught.
.Using a standard screwdriver, undo the three fasteners just behind the brush.
.Remove the base plate.
.Remove the belt.
.Remove roller brush.
.Place new belt on roller brush and center it in position.
.Feed belt through the hole, and return brush to position.
.Ensure the brush ends are located in the slots correctly.
.Pull the belt over the motor shaft.
.Rotate the brush a few times to ensure belt is centered and secure.
.Replace the base plate, tighten fasteners, and rotate the brush a few more times to make sure it turns properly and the belt isn’t caught.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
How do you replace the band in a dyson dc07? – Dyson DC07 Bagless Upright Cyclonic Vacuum
ANSWER : DC07s have two belts – one connects the output of the motor to the clutch, the other connects the clutch to the brush bar.
I suspect the belt you are to refering to is the one from the clutch to the brush bar. Unfortuenately the other belt is hidden under a plastic cover, so you cant see if it is okay or not without some dismantling. This cover is not easy to remove and requires a Torx driver to under the securing screws.
Have a look at www.dysonmedic.com, but unless you have access to such a tool, probably time to call Dyson or a Vacuum repairer.
I suspect the belt you are to refering to is the one from the clutch to the brush bar. Unfortuenately the other belt is hidden under a plastic cover, so you cant see if it is okay or not without some dismantling. This cover is not easy to remove and requires a Torx driver to under the securing screws.
Have a look at www.dysonmedic.com, but unless you have access to such a tool, probably time to call Dyson or a Vacuum repairer.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Replace power cord on Dyson DC07 – Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
ANSWER : The following link will take you to an article on how to change the motor on a DC07. Look at photos 4, 5 and 6 which shows how to disconnect the power cord.
.
.http://www.dysonmedic.com/DC07%20Folder/DC07%20Motor%20change.html
.
.Reassemble by reversing dissassembly instructions.
.
.http://www.dysonmedic.com/DC07%20Folder/DC07%20Motor%20change.html
.
.Reassemble by reversing dissassembly instructions.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
