Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum\015 I read your comment on replacing the power cord on the Kenmore Vacuum and got the vacuum opened and right to where the cord should go but the wires are not connected. I have a black wire with a switch on one end and a white wire on my power cord. Inside I have a black cord and another black cord with white stripe coming up from below. Then I have a small circuit board with black and white smaller wires. Also a light with a black and white wire coming out of it. I am assuming I connect black with other black wires and the white wires with the black wire with the white stripe. Does that sound right to you. Thanks for any help. Steve\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Check service panel for tripped breakers/blown fuses. If breaker is tripped, reset it. If fuse is blown, replace it. If vacuum cleaner is plugged in, be sure power button is in the off position before resetting breaker/changing fuse.
How long do Kenmore vacuums last? A. It`s suggested that the typical vacuum can last up to an average of eight years. With proper maintenance, a Kenmore vacuum could last that long or longer.
Vacuum cleaners are fairly simple machines. They need power to be transmitted to the vacuum to create a suction force that lifts debris. So, the usual areas that cause suction loss include the wrong height setting, stuck rollers, a faulty gasket, a broken vacuum belt, a filled bag, or a clogged hose.
The bottom line. Many vacuum brands recommend changing the bag before it becomes full, at least every three months.
You should replace the belts on your vacuum at least every three to six months if the vacuum is regularly used. This is very important for proper cleaning.
Your Vacuum Has Suddenly Gotten Extra Noisy
Just like noises under your car hood, belts that are stretched to the breaking point, or that have become loose can indicate that problems are on the way.
– Some vacuums have an in-line thermal fuse (often located between the switch lead and the motor coil). If the fuse is blown it will need to be replaced. – Check your home circuit breaker – it may have tripped. – Some vacuums have a brushroll on/off control.
One caveat: Handling this vacuum`s 23 pounds takes some muscle. In our member survey, Kenmore canisters earned a very good score for predicted reliability and an average rating for owner satisfaction.
The average life expectancy of a mid-range vacuum cleaner is about six years. You can fix or replace things like blocked filters, jammed brush rolls, frayed hoses, worn-out stick vac batteries and broken accessories yourself.
With all electronics it is best not to continually leave it at charge. It`s always good on the go and will hold a good residual charge. If you have a specific day or time of the week you vaccum then plug it in the that morning or night before. It only takes three hours for a full charge.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
The Full Dust Bag Indicator in On
It is often recommended, however, that dust bags are replaced when they`re around two thirds full or once a month. Daily and extensive use of vacuum cleaners will create a need to replace dust bags more frequently.
Can vacuum storage bags be reused? Yes. Vacuum storage bags can be used again and again.
As a general rule, if the repair is going to cost less than half the cost of a new vacuum cleaner, it`s best to go ahead and get it repaired. When the service tops half the price of a new machine, it`s probably best to invest in a newer model.
If your vacuum is fairly new and this is the first time you`re experiencing a problem, repairs are probably the best option. In fact, your vacuum may still be covered under warranty. However, if you`ve had to pay for multiple repairs and you`ve had the appliance for many years, it might be time for a new one.
Luckily, changing a vacuum belt is a very simple repair on most vacuum cleaners. Vacuum owners should never have to take their machine to a shop just for a belt replacement. The first step in this (and any) part replacement is to accurately order the needed part for the repair.
A typical price for Vacuum Belts is $6 but can range from approximately $4.99 to $26.
The fuse will be located on the right side of the plug. Lift it with your screwdriver to dislodge it. Replace the fuse with a fuse of the same amperage (check the appliance`s instructions if unsure) Reassemble the plug, plug it into the wall and switch the device back on.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
This overload reset switch button (part number 8191505) is for vacuums. Overload reset switch button 8191505 resets the overload switch when you push it. Unplug the vacuum before installing this part. Wear work gloves to protect your hands.
Lack of power, a bad power cord, failed drive motor or broken wires in the vacuum hose can prevent the vacuum cleaner from starting. Make sure the electrical outlet that you`re using for the vacuum cleaner works. Try using a different outlet if you suspect that the outlet you`re using is dead.
This overload reset switch button (part number 8191505) is for vacuums. Overload reset switch button 8191505 resets the overload switch when you push it. Unplug the vacuum before installing this part. Wear work gloves to protect your hands.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Replacing Power Cord Kenmore Progressive Upright
ANSWER : That actually sounds correct, if it’s the model I’m thinking of. As long as you’re talking about connecting to the wires that are held in by the wire nuts you should be good to go.
.
.-R
.
.-R
Read Full Q/A … : Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum
Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #’s anywhere online, not even partsdirect.com. any help would be great. thanks, david
ANSWER : Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est
Read Full Q/A … : Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum
The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections:
1 at the handle / upper wand
1 at the lower wand top of the power brush attachment
1 at the handle / upper wand
1 at the lower wand top of the power brush attachment
I replaced the entire wand assembly and it worked great for a year or so and now it’s doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu
ANSWER : This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it is plugged in together.
Read Full Q/A … : Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum
Cord rewind The power cord is jammed and won’t go in or out. I can’t find a way to get the cover off to have a look at it. Any suggestions please?
Power cord jammed won’t go in or out. Can comeone tell me how to undo the casing to get to the power cord?
Power cord jammed won’t go in or out. Can comeone tell me how to undo the casing to get to the power cord?
ANSWER : Which model do you have..
Read Full Q/A … : Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum
How to replace power cord on Hoover WindTunnel upright vacuum
ANSWER : The aforementioned solutions probably never even attempted this fix on this model. The handle does NOT need to come off. but the 5 screws on the front housing DO: 2 above the light and 3 below it. Then to get the colored housing off you need to access 2 screws on the underside that are beneath the agitator roller. To do that, obviously the 4 screws holding the bottom plate need to come off too. Here’s a link to a schematic that might help as you attempt to do this, (assuming that you still do!) http://www.elkypro.com/hoops2005/vacuum_parts/hoover/U5461-900.html
Once you have the main body housing cover off, then you can access the 2 screws atop of each trunnion cover that holds the motor assembly cover halves together. If you’ve made it this far, then gently pry apart the motor halves keeping even as yo do. Now you can see all the wiring necessary to cut and splice. Happy cord replacing! As for me, I am headed for the store, as I am not so sure I can remember how to get the darn thing put back together. But it was fun taking it apart!
Read Full Q/A … : Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum
Replacing Power Cord to Power Nozzle
ANSWER : The height adjust mech. has 2 tabs, that you have to unlock, It also is easier when you tip the power head so as not to puit pressure on the Ht. Adj. wheels. Use a flat blade screwdriver and if you look down bertween the ht. adj. mech. and the elboe where the wire is, you should be able to see the 2 tabs, just pry it away form the elbow and it will come off. When you put it back on, make sure all wires are routed where they were and tip powerhead, it will snap into place.
Read Full Q/A … : Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum
GE canister 106766 Power cord does not stay in bezel
ANSWER : Yes you are absolutely right.you would save on shipping cost if order both together.
.
.and for parts you can also order it from
.www.radioshack.com
.or from the source which you already have it with you.
.thanks.you are on the right track.you can continue ordering the parts.
.please do rate the solution.
.keep updated.thank you for using fixya.
.
.
.and for parts you can also order it from
.www.radioshack.com
.or from the source which you already have it with you.
.thanks.you are on the right track.you can continue ordering the parts.
.please do rate the solution.
.keep updated.thank you for using fixya.
.
Read Full Q/A … : Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum
Replacing a fraayed and twisted power cord on a Hoover windtunnel upright
ANSWER : Ok so I took this vaccum apart completely except for the electrical and motor systems. It seems to me that without dismantling both of these systems on the vaccum you can’t replace the power cord. And I wouldn’t recommend taking them apart unless you know what you are doing since replacing the power cord seems to require cutting the old power cord and soldering the new one onto the old terminals. All in all its probably easier to get a new vaccum altogether.
Read Full Q/A … : Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum
