Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum\015 The cord is frayed where it comes out of the vacuum near the handle. It’ always been very warm while vacuuming. I can replace it if I knew how to remove the plastic housing where the cord enters the machine. Can you help?\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

If your vacuum will not turn on and the power cable/connector is faulty, use this guide to replace the power cable/connector. You will need wire strippers, wire end caps, and the T10 and T20 Torx Screwdrivers. Reassembly requires rewiring.
It`s also important to pay attention to the vacuum cords. Tishko recommends checking them daily. Replacing a cord might cost $85 in labor and up to $130 for the new part.
If the cord itself is frayed or has exposed wiring, you`ll need to replace the entire electrical cord. Replacing only the plug could leave you open to electrical shock.
Many vacuum cords have small amounts of lead in the outside coverings, which can rub off on hands. If people eat or put their hands in their mouths after touching the cords, they can take in small amounts of lead.
Regardless if a cord is damaged by age, heavy use, pinching, or bearing too much weight (when an appliance is hung by its cord), a damaged cord increases the risk of electrical shock, fire, or electrocution, and should NOT be used. “The electric cord on your appliance contains a live wire that is securely insulated.
As a general rule, if the repair is going to cost less than half the cost of a new vacuum cleaner, it`s best to go ahead and get it repaired. When the service tops half the price of a new machine, it`s probably best to invest in a newer model.
Vacuums: For the past decade, Kenmore`s flagship vacuums were made by Panasonic (less-expensive models came from TTI, Eureka, and PhoneMate). Now that Panasonic is winding down its North American small appliance business, upcoming Kenmore vacuums will be manufactured by a company called Cleva.
Check service panel for tripped breakers/blown fuses. If breaker is tripped, reset it. If fuse is blown, replace it. If vacuum cleaner is plugged in, be sure power button is in the off position before resetting breaker/changing fuse.
Using a heat gun, some soldering wire, and a cutting tool, you can fix the faulty or broken wires, and restore your laptop`s charger to working condition.
Accidentally cut your good, heavy-duty extension cord? Replacement cords are expensive, and you can save money by just repairing it. Instead of splicing, add a new plug on the piece of the cord with the receptacle and a new receptacle on the piece of the cord with the plug.
A cable is an assembly of one or more conductors (wires) with some flexibility. A flex is the proper name for the flexible cable fitted to mains electrical appliances. A lead is a complete assembly of cable and connectors. A wire is a single conductor which may have an outer layer of insulation (usually plastic).
As of 2021, most electrical cords are still made with PVC, which contains lead. There is no safe or acceptable level of lead to have in your body, other than zero.
A flexible cord may be damaged by door or window edges, by staples and fastenings, by abrasion from adjacent materials, or simply by aging. If the electrical conductors become exposed, there is a danger of shocks, burns, or fire.
Summary. Vacuum cleaners last a long time. Corded vacuums tend to last around 7-8 years, although some brands are much more durable than others. Any vacuum with a battery is likely to last a shorter time – especially if the battery isn`t removable.
For a simple, straightforward way to repair a cord, fit it with a new plug. If you can`t find a new plug and wish to preserve the cord`s length, you could apply metal solder with a soldering iron for a stronger fix. Then, plug in your repaired cord to see that it works as well as a new one again.
We recommend dusting before vacuuming, this is because dust particles usually get moved around the room when you dust, meaning all your hard work will go to waste. A top tip is to wait at least 2 hours after dusting to get the vacuum out.
Factors may include having a bad motor, incompatible pump applications or poor ventilation. Constant overheating may indicate a malfunction.
Vacuuming every day, or even a few times a day, is not going to create any long term problems. `But,` you might be thinking, `doesn`t the brushes spinning over the carpet on a beater bar wear it out? ` Sure, but a very small amount.
“We would recommend vacuuming at least once or twice a week—and more often if we have pets—with the right tools to remove dust quickly and effectively,” Patel advises.
Kenmore is an American brand of household appliances owned and licensed by Transformco, an affiliate of ESL Investments. As of 2017, Kenmore products are produced by manufacturers including Whirlpool, Samsung, LG, Electrolux, Panasonic, Cleva North America, and Winia Electronics.
Whirlpool makes washing machines, dishwashers, and refrigerators that bear the Kenmore badge. In addition to Whirlpool-branded appliances, the company also manufactures Amana, Jenn-Air, KitchenAid, and Maytag kitchen and laundry appliances.
We warranty each vacuum cleaner to be free of manufacturing defects, and we will replace with a new product at equal or greater value or provide a full refund, at our discretion, any genuine Kenmore vacuum cleaner that is deemed defective.
Fraying: Do you see obvious damage to the USB cable? If you notice that the cord is bent or fraying, it is probably time to replace it. Damage is not always visible, though, so try plugging the cable into a USB port on a computer rather than using the wall adapter to determine the source of the problem.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?
ANSWER : Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I’m surprised it lasted as long as it did.
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
ANSWER : The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal.

Replacing the electical cord on Kenmore Progressive Vacuum
ANSWER : To the right of where the cord comes out of the machine is a large screw. Remove it, and slide the upper handle assembly free.
.Then, on the front of the machine, remove the screws located toward the top of the vacuum just inside the bag chamber cover. This will allow the front panel to be removed, giving you access to the cord from the front.
.
.-R

Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.

Replacing Power Cord Kenmore Progressive Upright
ANSWER : That actually sounds correct, if it’s the model I’m thinking of. As long as you’re talking about connecting to the wires that are held in by the wire nuts you should be good to go.
.
.-R

I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.

Vacuum not running; do I have to replace the cord winder or just cord?
ANSWER : Typically, the cord and winder are supplied as a unit.  It is possible to fit new cord to an existing winder, but the amount of labour involved will make the job more expensive than simply exchanging the complete unit.  Even if you’re going to do the job yourself, it’s simply not worth planning to just fit new cable (unless you are a masochist with unlimited time and patience).  Pay that bit extra for a complete unit – you’ll be glad you did (or you’ll be sorry if you don’t!).

How to replace power cord on Hoover WindTunnel upright vacuum
ANSWER : The aforementioned solutions probably never even attempted this fix on this model. The handle does NOT need to come off. but the 5 screws on the front housing DO: 2 above the light and 3 below it. Then to get the colored housing off you need to access 2 screws on the underside that are beneath the agitator roller. To do that, obviously the 4 screws holding the bottom plate need to come off too. Here’s a link to a schematic that might help as you attempt to do this, (assuming that you still do!) http://www.elkypro.com/hoops2005/vacuum_parts/hoover/U5461-900.html

Once you have the main body housing cover off, then you can access the 2 screws atop of each trunnion cover that holds the motor assembly cover halves together. If you’ve made it this far, then gently pry apart the motor halves keeping even as yo do. Now you can see all the wiring necessary to cut and splice. Happy cord replacing! As for me, I am headed for the store, as I am not so sure I can remember how to get the darn thing put back together. But it was fun taking it apart!