nd – tried to start after absence.
I have removed some hair and perhaps dental floss.
Checked belt – it seems O.K.
Do I need a new battery or is it just worn out.
Vacuums
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If you have checked for airway blockages and have cleared your filters, a damaged or deteriorating hose may be causing your vacuum`s loss of suction. On most Shark vacuums, there are two hoses to check, the short hose between the main vacuum head and the base, and the hose between the handle and the wand.
If your Shark ION Robot R75 vacuum stops moving unexpectedly after a few minutes of normal movement, it may simply have low battery power. Check that the device is powered on and that the battery has a significant charge.
One of the most common reasons for your shark vacuum (and most vacuums for that matter) making a loud suction noise is because there is a blockage. They`re a very common issue, and easily fixed. Blockages occur when there is a large enough build up of dirt or dust that it blocks the air flow to the vacuum.
If you checked your brush roll, floor setting, and belt but your brush roll is still not spinning, that means you probably need a Shark micro switch replacement. This small switch tells the vacuums brush when to start spinning.
Loose connections will cause your vacuum cleaner to lose suction. Make sure that the dust container, the hose, the tube and the brush are all attached properly. If the problem continues, your vacuum cleaner might have a technical problem. If you suspect this to be the case, contact an authorised service agent.
How I fixed mine with the same issue: Pull the roller out. Remove any hair you can find. Spray WD40 into the side of the brush roll that spins (with the metal tip) and spin that until it spins freely. Then out your roller back in and it is good to go!
To reset your shark vacuum, put the Power button in the On-Off position and keep the vacuum unplugged. If necessary, clear the hose. Once it has cooled completely, plug the vacuum back in again.
Check for a clogged hose or filter; unclog the hose and replace the filter. Wait 45 minutes for the vacuum to cool; then plug in the vacuum. Turn the power switch to the “I-On” position to start the vacuum. If the vacuum still does not start, contact Customer Service at 1-800-798-7398.
That depends greatly on the vacuum itself and what you`re using it for. A Shark vacuum that spends its days cleaning pet hair and other everyday messes might last as long as a decade. Investing in the best portable steam cleaner can last for a long time as well if they`re well taken care of.
There may be debris wrapped around the roller that is preventing it from turning. This is often due to hair, string, or other larger items that may be suck in the roller. Open the brushroll garage by sliding both of the release buttons away from you and then lift off the garage door.
If the indicator light is flashing red, the thermostat is overheating. To reset the thermostat, turn off and unplug the vacuum. Empty the dust cup and filter and assure there are no blockages in the hose. Allow the vacuum to cool for at least 45 minutes before turning it back on.
Clog located in the vacuum hose
Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.
Robot Not Collecting Debris
Ensure that the brushes beneath the robot are clean and in good condition. If hair or a build up of debris is found, take the following steps: Remove the brushes from the base of the robot. Using a damp microfiber cloth, clean the bristles of any hair or obstructions.
That depends greatly on the vacuum itself and what you`re using it for. A Shark vacuum that spends its days cleaning pet hair and other everyday messes might last as long as a decade. Investing in the best portable steam cleaner can last for a long time as well if they`re well taken care of.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Shark/cordless /sweeper – over four years old.
Started – but seemed like it was caught and shut off almost
immediately. Not used year around – tried to start after absence.
I have removed some hair and perhaps dental floss.
Checked belt – it seems O.K.
Do I need a new battery or is it just worn out.
ANSWER : Check the brush,is there any dirt got stuck in between brush rolls.If there is then it needs to be cleaned.Your cordless sweeper will automatically shut off if an obstruction is caught in the brush roll. the other thing to checks is dust container.Check in case if dust container is full and its not got emptied.If the dust container is full then it needs to be emptied,other wise brush roll will not spin and unit will shut off..———– But if all this things checked out ok then yes the battery needs to be recharged and checked.The battery needs to be charged for at least 4 hours to make the sweeper work,if the sweeper was not used for few months.But if the battery is not getting charged then the battery needs to be replaced.In some cases the battery charger it self gets short,so it does not charge the battery.To confirm that you will have to buy new battery and check.If the new battery is getting charged then charger is ok ,otherwise new charger also has to be ordered.The charger getting faulty is rare,but was noticed faulty in some cases.But if both charger and battery if they are working and still the same problem is noticed in sweeper then its faulty sweeper motor and controlling board.But this problem is very rare.As per the problem which you mentioned.the new battery should help.But you will have to confirm it by replacing battery.—————- This will help.Thanks.Helpmech..
Read Full Q/A … : Vacuums
Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn’t seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right….can you help. I am v
ANSWER : I’ve successfully used a compatible belt – Royal 104425001 .It’s still new, but for the time being at least – it works.
Read Full Q/A … : Vacuums
I purchased a brand new P113 Ryobi charger about 2 years ago. It has never worked. If I put a P104 battery in for a charge, it looks like it works correctly. I push the battery tester on the battery itself, and it says full charge, but when I go to use the bateery, it dies right away. I have tried three new P104 batteries. The batteries charge on my charger at work with no problem. The funny thing is, I don't need a battery in the charger and the charger does the same thing, It runs the test
ANSWER : If you have your receipt, check with Ryobi to see if it is still under warranty. It comes with either a 2 or 3 year warranty, depending on when it was purchased. If it is still covered, get it replaced/repaired. If it is not, buy the P117 charger. $30 at Home Depot. It has a 90 day satisfaction guarantee. If it charges your batteries properly, you’re good. If not, bring it back if you don’t like/want it. My P113 won’t get out of test mode now, or charge Lithium batteries anymore. So I bought the P117 yesterday. Works great, and it’s a lot cheaper than new batteries! And it has a 3 year warranty.
Read Full Q/A … : Vacuums
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
ANSWER : The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal.
Read Full Q/A … : Vacuums
I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn’t seem to turn properly and seems that it doesn’t pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt……
ANSWER : Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place..Also be sure the belt is properly installed so that the brush turns in the correct direction..If the brush is not turning or not turning in the correct direction, it will not beat the dirt from the carpet so that it can be picked up by the vacuum’s suction.
Read Full Q/A … : Vacuums
Have a Centralux Aerus about 5 years old. Don’t see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced
ANSWER : There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself
Read Full Q/A … : Vacuums
I have a Eureka 4870GZ. It turns on, but the brush roller doesn’t move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can’t get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there’s supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don’t see it. It looks like the motor shaft goes into a recessed place in the
ANSWER : Remove the top cover so that you can access to belt, You’ll find 2 rows of 4 decorative holes on the top cover, In two of the holes you’ll find the screws, Please use a flash light to see in that., Once the screws are removed, you’ll be able to take out the top cover. Pull the belt so that it should rotate the shaft and look for small space in between from where you can take off the old belt and new belt on. remove the agitator from its drive shaft, put new belt in, put the agitator back into place.
Read Full Q/A … : Vacuums
Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
Read Full Q/A … : Vacuums
