Euro-Pro Shark Steam Blaster Vacuum\015 The turn cap where one would fill with water wont open even if pushed and turned\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Check to see if there is water in the water tank. If there isn`t, unscrew the water tank cap and use the filling flask to pour distilled water into the tank until it reaches the fill line. Replace the water tank cap and tighten. Power the device on, wait about 30 seconds for the water to heat up, and then try again.
The spray tip may be clogged. Use a paperclip and insert it into the spray tip to remove a clog. Now plug back in, making sure you are using a working outlet. You will know, as the Ready light will begin to blink when plugged in.
Our testing has found that all steam mops remove stains fairly well, with marginal differences, and are likely slightly better than a regular mop and bucket due to the heat and vapour produced by the steam.
To prolong the life of your steam mop, we recommend using distilled water in the tank. Make sure you only add water to the tank – chemicals or cleaning solutions (including vinegar) may damage the steam mop and could be unsafe. For best results, sweep or vacuum your floors prior to cleaning with your steam mop.
check the cap of the water tank to make sure it is correctly and securely attached to the water tank. check your water tank to make sure it is securely and correctly fitted in to the body of the garment steamer – incorrect placement of the water tank can block water from feeding in to the body and boiler of the steamer.
Pull the wound-up power cord out of the mop and plug it into a 120-volt outlet. The on/standby button will start flashing blue. The mop only takes about 30 seconds to fully heat up.
If your account has been locked, please login to your Steam account and click on the red Steam alert banner for more information and for the length of the restriction. The block may be related but is not limited to: The use of graphic or otherwise inappropriate avatars, screenshots, artwork etc. Spamming the community.
Check for a clogged hose or filter; unclog the hose and replace the filter. Wait 45 minutes for the vacuum to cool; then plug in the vacuum. Turn the power switch to the “I-On” position to start the vacuum. If the vacuum still does not start, contact Customer Service at 1-800-798-7398.
check the cap of the water tank to make sure it is correctly and securely attached to the water tank. check your water tank to make sure it is securely and correctly fitted in to the body of the garment steamer – incorrect placement of the water tank can block water from feeding in to the body and boiler of the steamer.
Tap the mop firmly on the floor a few times to get it steaming again. My mop is still not steaming. Try running a bit of vinegar through your mop. There may be a mineral build-up from your tap water.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
For some reason, our shark steam mop stop working. Usually after I plug the steam mop, the power light would light up then you would hear & see steam coming out of the mop’s head but all of
ANSWER : HEATING ELEMENTS BURNT OUT. WILL COST OVER $100. TOFIX. SHARK NOW HAS A NEW MODEL “SHARK 3” MUCH BETTER
Read Full Q/A … : Euro-Pro Shark Steam Blaster Vacuum
I can’t get my shark steam blaster model EP95 to create steam?
ANSWER : Pull the (3) coasters/feet out and unscrew the 3 screws. take off the one end of the steam”boiler” (two clamps). tilt open end up and pour white vinegar [carefully] in there, prop up so it does not fall over, and soak overnight. dump out lime and water scale and rinse out a couple of times. Be very careful to not get water on electrical parts.
Take an air pig and blow out the line (Black) from where you disattached it to where the steam comes out [at the handle]. Be sure to mark electrical connections [4 on one, 2 on the other] so you don’t blow a breaker switch like I did.
Take an air pig and blow out the line (Black) from where you disattached it to where the steam comes out [at the handle]. Be sure to mark electrical connections [4 on one, 2 on the other] so you don’t blow a breaker switch like I did.
Read Full Q/A … : Euro-Pro Shark Steam Blaster Vacuum
Shark Steam Mop – Gray/ Purple Vacuum: shark steam mop has water, but there is no steam….
ANSWER : I tried running vinegar through as you would a coffee pot to get rid of hard water scales. This did not work. Then I noticed that the light behind the shark decal on the front of the machine was going off and on. And sure enough as I moved the cord around the light would come off and on. Looking closer I could see the the heat had melted thru some of the cord.I bought mine at Target before xmas last year, throwing away the sales slip after several months so I guess there is nothing I can do about it.
Read Full Q/A … : Euro-Pro Shark Steam Blaster Vacuum
Producing steam i just got the shark assembled the mv2010, then it is not doing anything, it vacuumed just fine, but when i put the steam pad on it wouldnt ever produce steam or do anything,it felt like the water was heating up but even after it sat for 20-30 minutes when i pull handle back towards me nothing happens, no lights no steam no nothing, so why wont it work
ANSWER : This link is for the manual
http://www.sharkclean.com/manual/MV2010_11_IB_ENG_110103.pdf
http://www.sharkclean.com/manual/MV2010_11_IB_ENG_110103.pdf
Read Full Q/A … : Euro-Pro Shark Steam Blaster Vacuum
My Europro shark steam mop won’t steam, light on but no steam.
ANSWER : Hard water deposits. I ran some white vinegar through mine, like a coffee maker, and it worked for a while, but clogged again. So I unplugged it, let it cool and turned it over in the bathtub and squirted a small amount of Lime-Away into the hole where the steam comes out. Let it soak for 5- 10 minutes and it is working like is is brand new.
Read Full Q/A … : Euro-Pro Shark Steam Blaster Vacuum
Shark steam blaster jr. makes steam but has no pressure
ANSWER : Yes no vinegar please. Try a product called scale clean or tablets for de-scaling coffee machines. Available from coffee machine retailers
Read Full Q/A … : Euro-Pro Shark Steam Blaster Vacuum
My shark steam mop does not steam – Euro-Pro Shark Steam Mop – Gray/ Purple Vacuum
ANSWER : Try cleaning the heating elements of lime deposits or adding a small amount of salt to the water.
Read Full Q/A … : Euro-Pro Shark Steam Blaster Vacuum
Shark S3501 steam mop will not make steam – Euro-Pro Shark Steam Mop – Gray/ Purple Vacuum
ANSWER : I posted this video showing how to clean the heater core of the S3501.
http://youtu.be/S4NglGXVv50
Read Full Q/A … : Euro-Pro Shark Steam Blaster Vacuum
