Stcc codes stcc code for woven plastic bags

ANSWER : The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full bag sensor is engaged. This second switch is supposed to get reset when you push the on/off switch on the outside of the machine. The full bag shutoff switch was stiff and it, therefore, was taking a couple of presses of the on/off switch to move the shutoff switch back into the running position.

ANSWER : Hi,

you can wash the bag. However you cannot wash the bag in the wash machine. What you will want to do is look for the screw or depending on the model, untwist the cap down on the rod next to the machine. that entire pole section will come off of the unit below with the bag there.

I recommend if it is warm outside to use the garden hose to spray it and scrub inside the bag with a scrub brush and some dish soap.

I usually throw them into the laundry sink and let soak, scrubbing with soap and water.

To dry the bag, a hairdryer or hang to dry before putting the piece back onto the machine.

Good luck.
Mark

ANSWER : First, if it runs without a bag, there’s a problem with the bag lock-out switch or wiring. This needs to be replaced/repaired by an authorized Aerus Electrolux technician.
.
.First, turn dial on top of vacuum counter-clockwise so the smallest dot lines up with the arrow. See if it stays on. If not, detach hose and turn vacuum on. Place palm of hand over intake. If it turns off, it’s possible that the tubes connecting to the CVA are clogged and simply need cleaned. This is most often caused by using “made to fit” Electrolux bags. Dust is sucked through the bags and into the motor compartment of the machine. All interior parts get covered in dust and need to be cleaned. If this is the cause, the vacuum is best cleaned and repaired at an authorized Aerus Electrolux store. If the vacuum shuts off, or won’t turn on before placing hand over the intake, it’s probable the control valve assembly is bad and needs replaced.

Another cause is an overheated motor due to clogged screen at back of bag well, full or clogged bag, dirty afterfilter, bad wiring/connections, clogged hose, clogged power head, or bad motor. It depends largely on the type and model of cleaner. Clogged wands are also a possibility, but unlikely.

Check and clean screen at back of bag well.

Replace bag. Make sure it’s a genuine Electrolux bag made by Home Solutions.

Check and replace afterfilter if necessary. These should be replaced after every six bags.

Broken and worn wiring connections are often found in the hose ends due to abuse and normal wear and tear. You can check the continuity of the hose using a continuity tester or multi-tester. If a multi-tester, turn dial to one of the Ohm settings. Place one probe into one of the terminals on the end of the hose. This will be referred to as T1. Touch the other probe to each of the terminals/connections on the other end of the hose. These will be T3 and T4. One of them should read zero, the other should read infinity. Repeat this with the other terminal, which will be T2.

Drop a marble in one end of hose and let it roll through. If it doesn’t roll through, the hose is clogged and needs to be cleared. Plug hose into the exhaust port of the vacuum, place other end in the in port. Turn vacuum on. This provides a blowing and sucking action which should clear the hose.
Detach hose from power nozzle (PN). Drop a marble into the wand end of PN. If it rolls through, it’s clear. If not, there’s probably a clog behind the brush where the intake opening is. You may be able to reach this through wand end with needle nose pliers, or either end with a knitting/crochet needle or a bent coat hanger.

If none of these “fixes” provide the answer to the problem, it should be taken to the nearest Aerus Electrolux store for diagnosis. Repairs or checks involving disassembly of the vacuum should always be done by an authorized Aerus Electrolux service technician.

The store nearest you can be found by following the instructions at the below listed link:
http://www.aerushome.com/storelocator/

ANSWER : I’m assuming this is the Epic 6500 or similar model.
.Detach the hose, turn vacuum on. If it runs, place palm of hand against inport hole. If it shuts off the problem is with either the control valve setting or the control valve assembly itself.
.For cvs, turn dial on top of vacuum all the way to the largest dot, and try above test again. If that doesn’t work, then it’s the CVA. It needs to be cleaned or replaced, which is an in shop job. Fro repair, take it to the nearest Aerus Electrolux store. I recommend a full clean and service to remove any dust/dirt from the motor, fan assembly, and other internal parts.
.
.Another problem, which relates to the dial setting, is that fine dust will quickly clog the pores of the bag, resulting in the machine “thinking” the bag is full. Turning the dial to the proper setting helps get the bag fuller. The middle setting is the normal setting, and is for areas without fine dust and sand.

ANSWER : Just ring your TelCo provider and they will give you one over the line

ANSWER : Your supposed to take out the plastic part that holds the bag but the way this unit is designed the lid will not close unless everything is inthere correctly so just make sure evverything in inserted correctly and keep trying! DO you still have your bag holder?

ANSWER : Yes you can wash it if it is from textile material, hand wash it i recomand, but not to sure if u can get all the hair out, but at least it will smell nice..
.A new bag isnt’t to expensive either, depends on the model....

ANSWER : Madam try to shake the bag to remove the dirt if you cant remove the bag. or use a strong electric fan and let it blow the dirt. hope that helps
.
.
.CHARCOIS