Steam is forming and coming from the water tank of the mop not down below from the pad area. Is it clogged?

Euro-Pro Shark Steam Mop – Gray/ Purple Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

The Cleaning Nozzle is clogged

Calcium and other minerals may build up in the nozzle, so you may need to clean the nozzle in order to produce steam. To do this, either use the nozzle cleaner provided with the Steam Pocket Mop, or use a straightened-out paper clip.

After use, unplug your steam mop and let it cool before removing the Dirt Grip pads. Empty the water tank before storing. Wait until it has fully cooled and all the steam has been released. Machine wash your Dirt Grip pads separately, with warm water, using liquid detergent.

Heating Element. A common cause to your cleaner not producing steam can be a failed heating element. As the heater is used to heat up the water, if that has ruptured or burnt out your steam cleaner will not produce any steam. With the water tank filled and switched on the steamer should sound like a boiling kettle.

Once you plug it in, it starts to heat up the water. To activate the steam, you have to pump the handle up and down. We usually started mopping instead of doing the 10 to 15 pumps because with your natural mopping motion you will pump the Shark Steam Mop each time you go forward.

What Should I Use? Good quality tap water. If you don`t have issues with hard water stains and buildup, your tap water is good.

Steam mops work by heating water in a reservoir or tank to about 250 degrees Fahrenheit. The hot steam travels to a microfiber pad through one or many jets that dampen the pad. The combination of steam and damp pad help moisten and break up dirt and dust from flooring.

Fill the Tank With Vinegar: Fill the water tank with distilled white vinegar or cleaning vinegar. Allow the vinegar to sit in the tank for at least 30 minutes (up to two hours is best) to help break apart the limescale and mineral deposits. Expel the Vinegar: Turn on the steamer and choose the highest heat setting.

Mix a teaspoon of laundry detergent and baking soda into 1–2 litres of hot water. Soak the mop heads in the cleaning solution for 30 minutes to an hour, then scrub them clean. Rinse them in clean water.

Product details

The Shark Steam Mop Replacement Pads 2-Pack is the cleaning pad option that works with the Euro-Pro XT3101 mop. These pads easily attach to the mop at the bottom and the pads can be machine washed and used multiple times over. This can help you to save money since they can be reused.

First, attach the mop pad to the mophead, then fill the reservoir with water using the filling flask. Once the steam mop is plugged in, it takes about 20 seconds for the steam to build up, and you`ll hear the mop hissing. During the first use, I found that I had to pump the handle a few times to prime the steam pump.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

For some reason, our shark steam mop stop working. Usually after I plug the steam mop, the power light would light up then you would hear & see steam coming out of the mop’s head but all of

ANSWER : HEATING ELEMENTS BURNT OUT. WILL COST OVER $100. TOFIX. SHARK NOW HAS A NEW MODEL “SHARK 3” MUCH BETTER

Read Full Q/A … : Euro-Pro Shark Steam Mop – Gray/ Purple Vacuum

I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!

ANSWER :

Call BISSELL Consumer Services.
.

1-800-237-7691
.

Mon-Fri: 8am to 10pm ET
.

Sat: 9am to 8pm ET

Read Full Q/A … : Euro-Pro Shark Steam Mop – Gray/ Purple Vacuum

Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl

ANSWER : There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap from the top. Also make sure that the lid in on and secured tightly.

Read Full Q/A … : Euro-Pro Shark Steam Mop – Gray/ Purple Vacuum

My steam pocket mop seems clogged. Steam does not come out of the mop head. The clog appears to be in the rectangular mop head. The triangular head still works fine. I’ve tried soaking it in hot water and soaking it with cleaning solutions. They have not worked. If I blow into the connection piece, no air goes through. That’s what leads me to believe there is a clog. If you can help, please do. I like the product and haven’t been able to use it for awhile because of this. Thanks.

ANSWER : I had the same issue with the rectangular mop and corrected it by disassembling the tube from the rectangular piece. There are two screws that will need to be removed in order to get access to the connector. Once the connector is removed from the rectangular piece you will need to **** out the clog. I used a small drill bit and was able to do this without attaching the bit to a drill. There is a slight angle to the connector which causes the clog to occur. The total job took about 45 minutes to accomplish. I could have purchased a replacement for $21.95 but thought I’d take a shot at fixing it. Hope this helps.

Read Full Q/A … : Euro-Pro Shark Steam Mop – Gray/ Purple Vacuum

After plugging in the steam mop, waiting for the 30 sec, pumping 12-15 times – no steam comes out. the tank is full and if i take off the bottom attachment the steam sprays everywhere. but the steam will not come out when mop head is on. thanks

ANSWER :

Hi,

Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it may not be getting steam to the head…

Euro-Pro Shark Steam Mop Problem