Hoover SteamVac F5914-900 SpinScrub Upright Vacuum\015 My SteamVac F5914-900 SpinScrub Upright Vacuum won’t stay upright and there’s no water suction.\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
HOOVER® SteamVac™ cleans carpet fibers by applying, scrubbing and removing hot tap water and cleaning solution.
A steam cleaner uses hot water vapor and a cleaning solution to displace and extract dirt, dust, and tough stains on your carpet. A vacuum uses an electric motor to suck dirt, dust, and hair from your carpet and hard-surface floors.
A possible cause might be that the tank is not properly seated. To assure the tank is seated properly, pick it up and re-seat is so it sits snugly on the unit. If this doesn`t fix the problem, make sure the tank is assembled properly. To make sure they are both latched properly, pick the tank up by its handle.
Here`s how to care for your carpet: It is a common belief that you should not vacuum new carpets immediately after they have been laid. This is not the case and you can, in fact, vacuum straight away. When your new carpet is fitted you may notice a few single tufts or loose ends standing above the pile.
Upright carpet cleaners are much more powerful than portable cleaners, and they use wider cleaning heads to grab more dirt and water from your carpets.
Pros of Upright Vacuums:
They are effective at cleaning thick carpets and rugs because they employ powered brushes. Your foot can easily manage the transition between bare flooring and carpeting. Unless you use a hose attachment, you won`t have to bend your back.
A shop vacuum`s ability to suck up water saves you from using towels to soak up water on the floor or trying to squeegee it away. A shop vacuum even acts as a pump to remove larger quantities of water standing in a tub, shower, pool, aquarium, or garden pond.
If you notice you`ve accidentally vacuumed water, the first step is to stop vacuuming the water and turn off the vacuum cleaner. If you`ve just suctioned a tiny amount of water, you may just need to allow the vacuum to dry out before using it again – this will ensure you don`t develop clogs.
A dry vacuum system does not use water to generate suction. A wet vacuum needs significant water flow to generate suction.
Some carpet steam cleaners use a combination of water and steam. These will be two tank machines, which collect water too. These are often better at stain removal than models which purely use steam. A carpet cleaner, on the other hand, uses water and carpet shampoo to remove a stain or general dirt.
The two settings – brushes up and brushes down are to help you clean both carpets and hard floors. When the brushes are up you can get nice and close to carpeted floors and suck up all the dust and nasties hidden in the fibres.
Check the dirty water tank and make sure there are no clogs in the hose below it. Remove the filter and clean debris from both the screen and filter. Also empty the dirty water tank and leave the filter out to dry completely before replacing it.
First, check to make sure the clean tank has water and/or the water & formula mixture in the tank. If your tank is empty, this could be the reason your machine is not spraying. You will need to fill your clean tank again. Reseat the tank and ensure it sits snug on the machine.
If the machine will no longer efficiently pick items up, the filter might be dirty. If after cleaning the filter your vacuum is still not sucking things up, turn your vacuum around and pull the red tab at the bottom of your Dyson out.
If you are vacuuming and notice that some dirt or debris is not being picked up then you should begin by checking and emptying the sweeper`s dust tray to ensure it is not overflowing. If the dust tray is empty and the pick-up performance hasn`t improved, turn the sweeper off and inspect it for any signs of damage.
Wash and Rinse Mode
Wash mode works with the solution to lift away any dirt from your carpet. While Rinse Mode removes any shampoo residue an water left behind after washing.
Vacuum Carpet Frequently
According to Shaw Floors, manufacturer of carpet, vinyl, hardwood and laminate flooring, you should vacuum the traffic lanes in high-traffic areas daily and the entire area twice a week. For rooms with light traffic flow, vacuum the traffic lanes twice a week and the entire area once.
Thus, it`s a good idea to shampoo your carpet once or twice a year, especially if you have pets in the home. Carpet shampooing can be accomplished by hand or steam cleaning using heat, water, and detergent to loosen and remove tough stains, spills, and odors.
A: Yes, you can just rinse your carpet with plain water when using the Hoover SmartWash Automatic Carpet Cleaner. Helpful?
Fill the water tank with hot tap water.
All Hoover carpet cleaners have a clean water tank and dirty water tank. Remove the clean water tank at the top by pressing on the lock on the handle. Unscrew the cap to the water compartment and fill the tank up to the fill line with water.
Using formula intended for an upright carpet cleaner in a portable machine can also lead to excessive foaming and potential resoiling, also known as restaining.
If the cleaner is still not spraying despite the water and detergent tanks being full, there may be a bubble of air stuck in the pump or the hose. To fix this, you need to turn the cleaner on and lower the hose down to the floor. Next, prime the pump by holding down the trigger for up to 1 minute.
Easy to Use
The one-piece design of upright vacuums makes them easier to move from room to room. Rather than bending down to deal with the canister, the handle on upright vacuums lets you push, pull, or carry the whole device with a single hand.
Upright Vacuum
They can be used as vacuum cleaners for hardwood floors and also carpets. They have a beater brush that is powered by an electrical motor and loosens up the dirt and sucks it up in its suction pump. Some Uprights might contain a bag to collect dust, while some might not.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
SteamVac F5914-900 SpinScrub won’t stay upright or collect water
ANSWER : (1) Upright: Sounds like the tab on the lower handle that the handel release latches to has broken off. The machine is fully functional without it otherwise.
.
.(2) Assure the ring gasket is in place under the hood. A round rubber gasket must be in place on the round tube under the hood where the recovery tank sits to connect the vacuum from the motor to the round tube on the bottom of the tank.
.
.(2) Assure the ring gasket is in place under the hood. A round rubber gasket must be in place on the round tube under the hood where the recovery tank sits to connect the vacuum from the motor to the round tube on the bottom of the tank.
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate
ANSWER : Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like it should. The big draw back to this model is Bissell has obsoleted all of its parts and most are no longer available. Might be wiser to buy new.
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
The Hoover Steamvac Widepath will NOT pick up water. The dispenser with cleaner DOES have water. The TANK that would receive the dirty water is NOT full. All tanks are on properly and the machine will still not pick up the used water. I found a tear in the interior hose leading to the receiving tank and repaired throughly with electrical tape. Still will not pick up the water. Any suggestions?
ANSWER : Sounds like a clogged air path (no vacuum action) from the floor pick-up to the collection tank. Take the tanks off and deal with the vacuum problem alone. The collection tank should have a air exit vent–is it clear? Check the interior hose that you repaired–is it clogged? Remove the bottom plate and inspect the air path from it. Because this machine deals with water, clogs can become like concrete! Hope this helps!
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl
ANSWER : There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap from the top. Also make sure that the lid in on and secured tightly.
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Won't pick up the water while cleaning – Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
ANSWER : Please check two three things:
.(1) Is the lid on the recovery tank aligned to the tank at rope seal of lid?
.(2) Is the rectangular panel in place in the front of the recovery tank, that connects the clear nozzle to the tank lid?
.(3) Remove the tank from the base, and check and see if a round black gasket is in place on the round tube that comes up to the front corner of the bottom of the recovery tank. This is a vacuum seal to connect the motor to the tank to supply suction.
.(1) Is the lid on the recovery tank aligned to the tank at rope seal of lid?
.(2) Is the rectangular panel in place in the front of the recovery tank, that connects the clear nozzle to the tank lid?
.(3) Remove the tank from the base, and check and see if a round black gasket is in place on the round tube that comes up to the front corner of the bottom of the recovery tank. This is a vacuum seal to connect the motor to the tank to supply suction.
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
ANSWER :
Call BISSELL Consumer Services.
.
1-800-237-7691
.
Mon-Fri: 8am to 10pm ET
.
Sat: 9am to 8pm ET
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
My steam VAC upright wont **** up water – Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
ANSWER : The most common and simple problem with these involves the recovery tank. Take it off, remove the cover and check to be sure it fits snugly. All tabs must be locked front AND back. If this machine has tools you have to hook up in order to use you more than likely forgot to put the small 5″x5″ tank duct in the front of the tank after using tools. This problem is caused by the recovery tank almost all of the time. Let me know if you need more help.
.
.Best of Luck
.
.Best of Luck
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
