Kirby G5 Bagged Upright Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

If too much hair, string, or lint is caught in the brushroll, the brushroll can get stuck. If the brushroll is stuck, it will put too much strain on the belt and may cause the belt to break. Remove the brushroll and clean out any debris from the bearings. After replacing the brushroll, make sure that it turns freely.
Often, a belt breaks because the machine is running over the edge of a rug or other thick items, perhaps even the vacuum cord. This causes “snagging.” When this happens, the belt becomes stuck and usually overheats. Unfortunately, this results in immediate breakage.
Kirby vacuums are constructed with die-cast aluminum parts. That`s what gives them their weight as well as their durability. However, when vacuuming, our amazing TechDrive® power assist makes the unit seem almost weightless. It senses the speed and direction that you want to go making vacuuming seem effortless.
All Kirby vacuums use the same size belt for the brush roller. This vac belt will fit every Kirby vacuum model roller brush, including: Avalir 2. Avalir.
Vacuum cleaners are fairly simple machines. They need power to be transmitted to the vacuum to create a suction force that lifts debris. So, the usual areas that cause suction loss include the wrong height setting, stuck rollers, a faulty gasket, a broken vacuum belt, a filled bag, or a clogged hose.
Q: What is the N/D pedal on the back of the Kirby for? A: This is your Neutral/Drive pedal. When you are vacuuming or using the carpet shampooer in the upright position, push down the Drive (D) pedal. This activates Tech Drive® power assist to make pushing your Kirby easy.
Spin burn can be cause by worn or damaged pulleys, and incorrect tensioning, which can wreak havoc on your belts causing damage and ultimately, premature failure.
How does a serpentine belt work? The serpentine belt uses pulleys and a belt tensioner to transfer power from the engine crankshaft to all the other components, says TheDrive.com. There is only one serpentine belt on most modern cars, and it is constantly moving whenever your car is running.
Use the extension/breaker bar on the grooved pulley tensioner arm, rotate the tensioner counter clockwise to remove the pin/bolt. Slowly allow the tensioner to rotate in a clockwise direction until the tensioner reaches the low stop. Remove the three bolts that attach the tensioner to the engine.
If a belt is not tensioned properly, it will ride too loose or too tight on the pulley. A belt that`s too loose on a pulley will cause slippage, which leads to heat build up from friction. This heat will damage your rubber belts and cause the belts to crack and break.
Rough Roads and High Speeds

Every hit and bump a tire experiences contributes to its degradation. Continued abuse will weaken the belts to the point that they begin to fail. Avoid gravel roads and hitting potholes at high speeds as much as possible.

Vacuum belts work to spin a vacuum`s brush roller and/or, on some self-propelled models, to turn a vacuum`s wheels. Whatever the style of vacuum, this repair will take placein the machine`s brushroll area.
The obvious answer to this is that Kirby has the easiest learning curve in the game, and is easy to pick up. The others are that he has spammable smash attacks, a rapid jab combo, and the suck up ability, which is useful when you don`t know how to mash out.
Kirby`s Copy Abilities Give Him Even More Versatility

Kirby`s copy abilities are every bit as powerful and more than Mario`s power-ups. And unlike Mario, Kirby`s power sources are far more common. He can inhale enemies, environments, projectiles, and much more to access new abilities.

There is no one-size-fits-all belt sizing formula. Belts fit differently depending on user sizes and gear combinations. For instance, gun belts measure different standards than a regular size guide due to the flexibility of various holsters. The intended use influences your choice of shapes and even material.
As we mentioned early, a serpentine belt delivers power to your alternator, power steering pump, and air conditioning compressor. In some cases, it also supplies power to your water pump. It`s a long, winding rubber band of sorts that is attached to your crank pulley.
Fine particles. Fine particles are no match for even the strongest vacuums. Construction dust, makeup, used coffee grounds, fireplace ash, and other fine particles can burn out the motor and be released back into the air. It`s best to sweep these items up to keep your vacuum – and yourself – safe.
The Dyson vs. Kirby vacuum cleaners debate can be complicated, as these brands are so different. If it comes down to price or size, Dyson will probably get the upper hand — but for all other vacuuming considerations, Kirby is the way to go.
Kirby (Japanese: カービィ Kābī) is the major non-Pokémon of the series Pokémon Dream Warriors. Kirby lives in his dome-shaped home in Dream Land, a country on his home planet Planet Popstar.
Kirby`s creator, Masahiro Sakurai, wrote Kirby`s profile which also lists the character`s gender as “unknown” and once jokingly stated that Kirby may actually be female, in reference to a question about Samus Aran.
Mini is a Copy Ability only available in Kirby & The Amazing Mirror which causes Kirby to shrink down to a smaller size, allowing him to fit through tight passageways. It is among the rarest abilities in the game, only being obtainable from Minny, an enemy primarily found in Mustard Mountain in very small numbers.
If your vacuum sealer is melting the bag too much and creating tears in the seal, try decreasing your seal time on your sealer. It may be too long for your bags. If your vacuum sealer isn`t sealing the bags all the way through, try increasing the seal time. The bags may need a little more time to properly seal.
A Type V-belts with a top width of 1/2 inches. B Type V-belts with a top width of 21/32 inches. C Type V-belts with a top width of 7/8 inches. D Type V-belts with a top width of 1 1/4 inches.
An easy way to determine belt size is to simply “add 2″ to your off-the-rack trouser size. For example, if you wear a 36” waist trouser, then a 38-belt size will be a safe bet. Most will find this simple formula works best for pants worn at a traditional height–close to the natural waistline.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Th end of the shaft that come from the motor is worn out, and won’t hold the belt well. How do I change it?
ANSWER : Hello,
.
.Thanks for the clarification. I have never seen this problem previously in a Kirby. I wonder if the belt keeps sliding off because it’s been stretched out? After about 1-2 years, the belts on the Kirby will stretch out to a point where there can possibly slide off the motor shaft. Have you tried just replacing the belt on the unit first?
.
.If you’re sure that it’s not the belt that may be stretched out, and you’d like to replace the motor shaft, you certainly may do this. The only problem with this is the motor shaft is not sold by itself as a separate part. The only way to purchase this motor shaft is to purchase the entire fan assembly, which includes a new fan, and the hardware necessary on the fan assembly.
.
.Here’s a parts diagram that shows you the motor shaft is sold only in a completely assembly:
.http://lib.store.yahoo.net/lib/vacuumcleanerbacgs/kirby-generation-parts-diagram.pdf
.
.If you haven’t already purchased the motor shaft, here’s a direct link to the motor shaft and fan assembly on our website:
.Kirby Generation Fan Assembly With Motor Shaft and Hardware
.
.In terms of installing it, we’ve actually recorded a video repair on how to replace the fan assembly, which involves removing the motor shaft in order to get the fan off. Since you have to purchase the fan assembly anyways in order get the motor shaft, you may want to go ahead and replace your fan assembly at this time also. Even though your fan may not be broken, on Kirby’s the fans can become coated with dirt and fine dust, which can sometimes lead to the Kirby exhausting a bad smell. If you’d rather not replace the fan, you may remove the motor shaft without disassembling the entire machine, you’ll just need to secure the fan somehow so that the fan doesn’t spin while you’re using a nail to turn the motor shaft off.
.
.Anyways, here’s the video repair that we recorded. I hope that this helps you. If you found this helpful, please kindly rate my repair helpful by clicking the thumbs up icons in the top right hand corner of the repair. This is really what keeps Fixya repair professionals continue to give free repairs online.
.
.Here’s Part 1 of the video:
.
.
.
..
.Here’s Part 2 on Replacing the motor shaft and fan:
.
.
..If you have any follow up questions, I’d be more then happy to answer them for you, please just add another comment here on the repair page, and I’ll be more then happy to answer any follow up questions that you have. Thanks again for rating the repair, I greatly appreciate this.
.
.
.Chris Jones
.GoVacuum.com

Read Full Q/A … : Kirby G5 Bagged Upright Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn’t move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can’t get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there’s supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don’t see it. It looks like the motor shaft goes into a recessed place in the
ANSWER : Remove the top cover so that you can access to belt, You’ll find 2 rows of 4 decorative holes on the top cover, In two of the holes you’ll find the screws, Please use a flash light to see in that., Once the screws are removed, you’ll be able to take out the top cover. Pull the belt so that it should rotate the shaft and look for small space in between from where you can take off the old belt and new belt on. remove the agitator from its drive shaft, put new belt in, put the agitator back into place.

Read Full Q/A … : Kirby G5 Bagged Upright Vacuum

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn’t seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right….can you help. I am v
ANSWER : I’ve successfully used a compatible belt – Royal 104425001 .It’s still new, but for the time being at least – it works.

Read Full Q/A … : Kirby G5 Bagged Upright Vacuum

Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won’t turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can’t get it to budge. This is exactly what is keep brush roller from turning.
ANSWER : Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn.

Read Full Q/A … : Kirby G5 Bagged Upright Vacuum

Putting the belt over the motor shaft
ANSWER : The belt may be overloaded because something it is driving is jammed or partially siezed . It could be a bad bearing or string wrapped around the beater brush etc. Check that everything moves really freely before going through this again. Take it all apart and clean it good. Don’t get any oil on the belt or pulleys, but make sure the bearings on anything thta turns is clear and lubricated.

Read Full Q/A … : Kirby G5 Bagged Upright Vacuum

Changing the belt
ANSWER : Just in case you’re still having this problem…. you don’t need to fit the belt around the motor shaft. Only wrap it around the brush roller and the piece near the back that you are able to put the belt around, and snap the brush back into place. It didn’t look like it would work (it looked like my cat could have done the same thing and gotten the same result) but it works gloriously now!

Hope this helps.

Read Full Q/A … : Kirby G5 Bagged Upright Vacuum

Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!

Read Full Q/A … : Kirby G5 Bagged Upright Vacuum

We own a dirt devil model 088600, and are experiencing a problem with the belt wearing away a section between where the belt connects to the brushes and the motor. There is a lot of plastic/rubber residue coming out from the vacuum. We have tried new belts only to find the same problem occurs. I noticed that the source of the dust is coming from the section between the brushes and motor, where there appears to be a section that is misshapen and melted. I looked up the schematic online and can’t
ANSWER : If you are certain that the belt is seated correctly and the beater bar is nested in its holder and the cover of the assembly has been properly installed and you still see a contact area between the belt and cover, you should either: return the vac to the place you purchased it for a replacement or just remove a small section of the cover that it is making contact with.. You can use a dremel tool , jewelers saw or equivalent to make that change. Have you compared your vacuum with another one to see if there are differences or other vacs have the same problem? Just a few ideas that may help you…

Read Full Q/A … : Kirby G5 Bagged Upright Vacuum