Hoover U5753-900 WindTunnel Bagless Upright Vacuum\015 The belt on my hoover will not stay on. It falls off almost as soon as I start vaccuming.\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
The bearings in the brush rslip. oll or bearings behind the fan could cause this. If you put the belt on and the brush roll is catching it would cause the belt to slip. If you have any a height adjustment it could be an issue.
If too much hair, string, or lint is caught in the brushroll, the brushroll can get stuck. If the brushroll is stuck, it will put too much strain on the belt and may cause the belt to break. Remove the brushroll and clean out any debris from the bearings. After replacing the brushroll, make sure that it turns freely.
If a belt is not tensioned properly, it will ride too loose or too tight on the pulley. A belt that`s too loose on a pulley will cause slippage, which leads to heat build up from friction. This heat will damage your rubber belts and cause the belts to crack and break.
Next to the motor, the belt on your vacuum is just about the most important part of your vacuum. Without the belt to spin the brushroll, most vacuums won`t pick up on carpeting at all! If your vacuum uses a rubber belt, check it once a month for cracks, melting, and especially, slippage.
One is to keep the belt clean and lubricated. Another way is to check the tension of the belt periodically, and make sure that it`s not too tight or too loose. The last way is to get your car serviced regularly so that they can inspect the condition of your car`s drive belt and replace it if necessary.
You should replace the belts on your vacuum at least every three to six months if the vacuum is regularly used. This is very important for proper cleaning.
Luckily, changing a vacuum belt is a very simple repair on most vacuum cleaners. Vacuum owners should never have to take their machine to a shop just for a belt replacement. The first step in this (and any) part replacement is to accurately order the needed part for the repair.
Improper belt tension is the most common and obvious cause of slip, which generates unwanted heat. The friction that occurs when a V-belt slips in a pulley causes belt sidewalls to become glazed, and decreases gripping ability.
If the belt is too loose, it will cause the alternator to slip. This slipping can cause the alternator and the battery to work harder.
In the technical sense, yes—you can drive a vehicle with a broken serpentine belt, but only for a short distance, as you may unexpectedly lose power at any time. If this happens while you`re on the highway, you are at serious risk of being hit by or colliding with another vehicle.
Package of (1) 38528-034 roller brush belt and (1) 38528-035 power drive belt for Hoover WindTunnel models with the self-propelled feature. Replace these belts every 6 months to ensure optimum performance.
The major types of vacuum belts are determined by their different shapes. As vacuum designs have improved over the years, new belt shapes have been developed to increase both their durability and their ability to transfer power from the vacuum`s motor.
Slippage occurs when the conveyor belt and pulley don`t have a strong grip. It usually happens around the head pulley and results from the pulley being unable to properly turn the belt around itself, reducing a project`s output.
If your vacuum runs but isn`t always picking up dirt, it might be time to change the belt. Consumer Reports` experts reveal how fast and simple it is to install a new belt which can save you a trip to the repair shop.
Serpentine belt replacement is easy because today`s automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning. Just rotate the tensioner, remove the old belt and install a new one.
I have had a chip in the cord of a vacuum . You can wrap it in electrical tape . I`d wrap it again in silver duct tape so I could be very sure of the repair won`t catch and unfray when you vaccuming .
A typical price for Vacuum Belts is $6 but can range from approximately $4.99 to $26.
How to do it: Attach a strip of double-sided tape to the inside of your belt end. Line the end up so it lays flat against your belt and press to secure.
If your vacuum is fairly new and this is the first time you`re experiencing a problem, repairs are probably the best option. In fact, your vacuum may still be covered under warranty. However, if you`ve had to pay for multiple repairs and you`ve had the appliance for many years, it might be time for a new one.
Synchronous belts require minimal maintenance and retensioning, operate in wet and oily environments, and run slip-free. However, synchronous belts are noisier than V-belts, less suited for use on shock-loaded applications, and transfer more vibration due to their stiffness.
There are a couple of factors influencing the answer to this question, but on average, your car should be able to run between 20-90 minutes with a broken serpentine belt. The engine will overheat faster without a functioning cooling system on a hot day, so your driving window is less.
The belt may be broken or worn
If you pick up something sharp or debris gets jammed in the brushes then the belt may snap. Also over time your belt will stretch, so it`s a good idea to change your belt once per year to ensure the cleaner picks up dirt effectively.
Underneath the cleaner is a brush bar that is driven by a rubber belt. It spins around sweeping and beating the dirt out of the carpet and up into the cleaner. The belt will stretch and wear out so it should be replaced once per year or sooner as a precaution if you feel the cleaner is not sweeping up effectively.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
Read Full Q/A … : Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn’t seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right….can you help. I am v
ANSWER : I’ve successfully used a compatible belt – Royal 104425001 .It’s still new, but for the time being at least – it works.
Read Full Q/A … : Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a ’97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I’m sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa
ANSWER : Honestly you should take it to a vac.shop they can fix any vac.
Read Full Q/A … : Hoover U5753-900 WindTunnel Bagless Upright Vacuum
My Mom has a Dirt Devil Featherlite and the belt falls off all the time. I put it on three times today and it falls off within a few minutes. The belt post I put it on doesn’t have anything to hold the belt on. Is there supposed to be something holding the belt?
ANSWER : It sounds like the belt is too worn and loose to stay on. Buy a new belt specified for that model of vacuum and install. Ensure that there is only a slight amount of give in the belt when you press the middle.
Read Full Q/A … : Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there’s two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it’s a ribbed belt? that is the water pump belt?
ANSWER : Just taken ours apart with the same problem… found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places – the bottom of the screw wells..This means that the water tank cannot exert sufficient pressure on the valve to release the water..Only solution is a new top cover assembly
Read Full Q/A … : Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught on the metal pole?
ANSWER : Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)
http://64.49.205.183/v/u6451900.pdf
Read Full Q/A … : Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Hoover bagless cannister 3765 – belt on power head slips off spindle. bought new belts – same problem. is this a design problem or can it be fixed? I don’t want to take it to a repair shop 100 miles away and have them just put on a new belt. saw idea of smaller belt – what number? couldn’t find suggested royal 104425001 belt.
ANSWER : I would not recommend a smaller belt. You will only wear the motor. This model series power nozzle needs to have a metal clip installed near the belt on the brush roller housing. I know that most of them left the factory without it. Remove the cover to see if one is ther. if not have your dealer send you a clip or a housing with one on it.
Read Full Q/A … : Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Have the empower upright cleaner. belt broke. can not find part #36528-040belt. can find a lot of hoover belts but not this #.Is there another hoover belt that will work on this vac?
ANSWER : No. if the wrong belt you will have problems. This is a common belt for Hoover, it used to be 36528027, but the number changed to the 36528040, also 40201190 is the newest number for this belt. Most repair vacuum repair shops should have this belt. You order it online at http://vacuumsuperstore.com/hoover_belts.html
Read Full Q/A … : Hoover U5753-900 WindTunnel Bagless Upright Vacuum
