Dyson DC07 Bagless Upright Cyclonic Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.
Press the brush control button located next to the ON/OFF switch to turn the brushbar off for vacumming delicate rugs, looped carpets and hard floors. Press the button again to restart the brushbar for vacuuming carpets.
One of the first things to do when your Dyson vacuum cleaner keeps starting and stopping is to empty the bin. It may be full, or the machine may simply perceive it as too full to continue working. Dyson vacuum cleaners require constant airflow through them to work, and a full bin can stop this from happening.
Brush Head Bearings Are Clogged or Have Failed
These are symptoms of bad or dirty bearings. You should remove the brush roll or rolls from the vacuum. Check to see that the bearings at the end of the brush roll allow it to spin freely. Make sure that there is no hair trapped in the bearings.
The rotary brush in the cleaner head of your Dyson V7 spins at high speeds and helps to beat and dislodge the dirt out of your carpets.
If you checked your brush roll, floor setting, and belt but your brush roll is still not spinning, that means you probably need a Shark micro switch replacement. This small switch tells the vacuums brush when to start spinning.
The Dyson Airwrap™ styler harnesses an aerodynamic phenomenon called the Coanda effect, propelled by the Dyson digital motor V9. It attracts hair to the surface of the brush, propelling air along the hair strands. Styling with air, not extreme heat.
Hold your brush bar under cold tap water and gently rub to remove any lint or dirt. Stand the brush bar upright and leave to dry completely. Make sure your brush bar is completely dry before refitting. The cleaner head housing is not washable and should only be wiped over with a damp lint-free cloth.
If your vacuum`s brush bar is not turning, the bar may be clogged from hair and other debris. Ensure that the brushbar button, which is gray and located next to the power button, is turned on. If this is not the issue, then the brushbar itself may be damaged or stuck.
It`s possible there`s a power consumption issue, with there just not being enough residual charge to run the machine. A new battery should fix this. My other thought is that it`s overheating. If too much power is pushed through the motor, which MAX power does, it could stop after a few seconds if it become hot.
Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.
If your machine has a clutch, the reason the brush bar isn`t spinning is unlikely to be a snapped belt. The clutch allows your brush roll to be turned off (for certain types of hard floors, etc.). First you should check if your brush bar is turned on. Try to turn the knob one click clockwise to the “auto” position.
`Tripped` reset systems are the most common reasons for a brushbar not turning, but there are some other less common reasons too. These include: If the bearings on the end of the brushbar have seized, you won`t be able to turn it at all. This will often result in a broken belt as well, so be aware of this.
A Dyson vacuum cleaner has a lifespan of around 10 years. This is considerably longer than most other vacuums. So, if you`re looking for a high-quality vacuum cleaner that will last you for a long time, a Dyson could be a good choice. However, remember that Dyson vacuums are expensive.
if your dyson DC 24 has a faulty brush bar motor now sometimes the brushes on these in to suddenly stop going around the first thing to do is to look on the side the brush bar housing and click this reset switch.
Reset the machine. To reset the machine, turn the power off (using either the power button on the remote or the Main body), wait 60 seconds and then turn back on.
Discovering the advantages of the on/off brush roll
Turning off the brush roll switches the vacuum to “suction-only” for quick and easy cleaning of hard floors. What`s more, the ability to switch between hard floors and carpets with the on/off brush roll means you only need one vacuum to clean your entire home.
What is a Beater Bar? A beater bar is a smoothly contoured metal agitator bar on a rotating brush roller. See below image. It works in conjunction with bristle brushes to gently beat the fibers, when the beater bar rotates, to loosen soil and allow the brushes to comb away the soil into the suction ports of the vacuum.
For smoothing and detangling your hair before styling. The Paddle brush is designed for usage comfort with an ergonomic handle, air-cushion suspension and rounded bristles.
1.6 inch Airwrap™ long barrel
Re-engineered so you can create clockwise and counterclockwise curls with one barrel, using the rotating cool tip.
The carbon brushes conduct electricity from the fixed parts of the motor through the moving parts of the motor.
You may visit a Dyson Service Center to have your Dyson machine serviced and/or repaired. If you are unable to visit a Dyson Service Center, you may ship your Dyson machine to Dyson for service and/or repair.
The most common cause of no power is the machine overheating and cutting out. In this case once the vacuum cleaner loses power leave it for at least half an hour and then try turning it back on again. If it comes back on again after an hour then clean your filters and check for blockages.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to “encourage” the brush to turn with a set of articula
ANSWER : There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver.
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”.
.Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
..
.Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”..Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
.
..Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Dyson dc07 brush not turning belt is intact? – Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
ANSWER : DC07s have two drive belts that turn the brush bar – one connects the output of the motor to the clutch, the other connects the clutch to the brush bar.
You can check the latter simply by removing the sole plate and looking. Unfortunately the other belt is hidden under a plastic cover, so you cant see if it is okay or not without some dismantling. This cover is not easy to remove and requires a Torx driver to under the securing screws.
If, after removing the cover, the other belt is okay, then you have a faulty clutch. New clutches are available on eBay reasonably cheaply, but again good tools and DIY skills are required.
Have a look atwww.dysonmedic.com which has some excellent info on dismantling and repairing a DC 07, but unless you have access to such tools, and feel confident to tackle it, it’s probably time to callDyson or a Vacuum repairer.
You can check the latter simply by removing the sole plate and looking. Unfortunately the other belt is hidden under a plastic cover, so you cant see if it is okay or not without some dismantling. This cover is not easy to remove and requires a Torx driver to under the securing screws.
If, after removing the cover, the other belt is okay, then you have a faulty clutch. New clutches are available on eBay reasonably cheaply, but again good tools and DIY skills are required.
Have a look atwww.dysonmedic.com which has some excellent info on dismantling and repairing a DC 07, but unless you have access to such tools, and feel confident to tackle it, it’s probably time to callDyson or a Vacuum repairer.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Electrolux vacuum brush not turning problem:
was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won’t even switch on. Hope you can help
ANSWER : Under the vacuum, there is a guard..remove the guard , either by 2 screws or by 2 clips..there is a belt under the guard..that is connected to the brush..the belt need to be replaced.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
How to put new cable on dyson dc07 upright – Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
ANSWER : Have a look at www.dysonmedic.com which has some excellent info on your machine.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Dyson vacuum turned off while vacuuming – Dyson DC07 Bagless Upright Cyclonic Vacuum
ANSWER : Hi There,
Assuming if you leave it for an hour and come back to it that it works again you have an airflow issue. This machine will cut out if the motor gets too hot. The likely causes are 1. Filters – take them out and give a good clean once dry you can try them again. 2. Blockage – Remove your u-bend and the blockage removal access check for an obstruction.3. Radix assembly is blocked. I will post a link to a YouTube video showing how to address this as it is a bit more difficult.
If your machine wont turn back on after a rest then your options are 1. Cord problem (most likely)2. Switch (unlikely)3. Motor
Assuming if you leave it for an hour and come back to it that it works again you have an airflow issue. This machine will cut out if the motor gets too hot. The likely causes are 1. Filters – take them out and give a good clean once dry you can try them again. 2. Blockage – Remove your u-bend and the blockage removal access check for an obstruction.3. Radix assembly is blocked. I will post a link to a YouTube video showing how to address this as it is a bit more difficult.
If your machine wont turn back on after a rest then your options are 1. Cord problem (most likely)2. Switch (unlikely)3. Motor
I have a video for just about all these problems on my youtube channel under VacuumSpot or VacuumSmart. If this is a step in the right direction please lay a thumbs up on the videos 🙂
If you need parts for your dyson in Australia check out VacuumSpot
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Noisey DC07 Bagless Upright Cyclonic Vacuum; lack of suction…
ANSWER : The washable filters very seldom wear out, they are sponge, but the prefilter on the housing CERTAINLY wears out. You can fix it here:
.
.http://www.ehow.com/how_5870417_modify-dyson-prefilter-suction.html
.
.http://www.ehow.com/how_5870417_modify-dyson-prefilter-suction.html
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Replace power cord on Dyson DC07 – Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
ANSWER : The following link will take you to an article on how to change the motor on a DC07. Look at photos 4, 5 and 6 which shows how to disconnect the power cord.
.
.http://www.dysonmedic.com/DC07%20Folder/DC07%20Motor%20change.html
.
.Reassemble by reversing dissassembly instructions.
.
.http://www.dysonmedic.com/DC07%20Folder/DC07%20Motor%20change.html
.
.Reassemble by reversing dissassembly instructions.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
