le checked seating of tank, placement of filled cleaner bottle and yes – it’s plugged in.
Bissell 1698-1 PowerSteamer ProHeat Plus Upright Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Carpet cleaners use a combination of clean solution, powerful scrubbing brushes and vacuum suction. Carpet cleaners inject a mixture of cleaning solution and water deep into your carpet fibres. Brushes then agitate, scrub and loosen the dirt and/or stain and then the powerful vacuum suction lifts it away.
A carpet cleaner is a device that mechanically applies soap and water to a carpet from a clean water tank, scrubs, and then suctions up the byproduct into a dirty water tank. Carpet cleaners work by applying and suctioning up water.
I like to pre-treat my stains by using a 50-50 mix of the concentrated solution and water. You can add it to a spray bottle or just use your fingers to dab a bit of it on the stain. Let it sit for 5 minutes then shampoo over it.
Hot water loosens and softens dirt more quickly, making it easier to remove, and it also helps to kill bacteria. That`s why we recommend filling up your carpet cleaner`s tank with warm water. Some BISSELL Carpet Cleaners also use HeatWave technology to keep the water hot throughout the cleaning process.
Your Vax carpet cleaner may not be picking up water because the machine has picked up too much grime, and has become blocked up. Check around the head of the carpet cleaner for anything obvious that might make the suction on the Vax weaker, or look for clumps of hair that could be caught in the bristles.
Try refilling the Clean water tank (B) Tank with clean water and appropriate amounts of Britex cleaning solution. Ensure the small solution hose is still connected at the front valve connection and the other end to the carpet wand; try a disconnect and reconnect.
A carpet shampooer will treat the surface of your carpet. A carpet steam cleaner uses heat to extract the dirt from the fibers. Decide how deep of a clean you require when choosing between shampoo carpet cleaning vs. steam cleaning.
Yes, you should keep cleaning the carpet until the water is clear. This will ensure that your carpets are clean and free of dirt, dust, and other allergens. However, you should be careful not to scrub too hard or use too much water. Doing so can damage the carpet and lead to more stains in the future.
Naturally, all carpet cleaners will leave some moisture, which will dry out in the hours following the cleaning process. However, if the carpet remains wet long after cleaning, it`s because the final step of that process was insufficient.
Soak Up Water

Using towels, preferably microfiber, spread over your carpet and pat down to saturate the towels. As towels become oversaturated, replace them with fresh towels and repeat the process. Be sure to move any furniture during this process and blot for water in those areas as well.

After you get out your carpet cleaner, fill the clean tank to the line with hot (not boiling) tap water. Hot water does a better job cleaning than cold but, if you boil it, you run the risk of melting parts of your carpet cleaner. Add formula to the tank according to the bottle directions.
Your carpet will be only slightly damp to the touch after your cleaning. Most carpets typically need 6-10 hours to dry completely. However, it could take up to 24 hours to dry depending on the time of year your carpets are cleaned, and the air circulation, humidity and temperature in your home.
Your carpet will be only slightly damp to the touch after your cleaning. Most carpets typically need 6-10 hours to dry completely. However, it could take up to 24 hours to dry depending on the time of year your carpets are cleaned, and the air circulation, humidity and temperature in your home.
How long does it take carpets and upholstery to dry after carpet cleaning? On the average, it will take approximately 2-4 hours for carpet and upholstery to dry after being carpet cleaned. To expedite the drying process, you will want to use a fan and increase your air circulation.
It`s not unusual for DIY carpet cleaners to need eight or even 10 passes on a carpet before the water runs clear. This is especially true when: It has been a long time since your carpet was last deep-cleaned.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

The carpet cleaner does not spray cleaner, nor vaccum up excess water. It’s been taken apart, cleaned, reassembled, refilled, twice. Have double checked seating of tank, placement of filled cleaner bottle and yes – it’s plugged in.
ANSWER :

Hi
..

..

The issue may be due to flow system; to troubleshoot the.system follow the instructions–
..

1. Remove Smart Mix piston from the main housing and place Smart.Mix body (located beneath the knob on the main housing, inside of the unit) so.that it is 1/16″ from completely inserted.
..

2. Replace tanks in unit.
..

3. Plug unit in and turn it on.
..

4. Pull trigger to check spray — making sure upper handle.is firmly positioned onto the lower handle. Water should flow through tubing.from the tank to the pump and the red float inside the pump should move up. If.it doesn’t, replace the pump.
..

5. Check the tubes for air bubbles as the unit is spraying.– bubbles indicate an air leak that prevents pump from priming.
..

6. Locate the source of any air leaks and correct them,.looking first at the auto load receiver (under the tank) and the Smart Mix.assembly.
..

Hope this helps…please post back for further assistance.
..

Daniel

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.

I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
ANSWER :

Call BISSELL Consumer Services.
.

1-800-237-7691
.

Mon-Fri: 8am to 10pm ET
.

Sat: 9am to 8pm ET

My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there’s a little thingy that should be spinning or turning….. When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI – I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn’t wet. Any tips? The manual doesn’t help.
ANSWER : You need to replace the pump belt. Here is the belt you need:

Bissell ProHeat Belt

I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate
ANSWER : Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like it should. The big draw back to this model is Bissell has obsoleted all of its parts and most are no longer available. Might be wiser to buy new.

Bissell ProHeat 2x Upright Carpet cleaner-water tank valve
ANSWER : Www.usavacuum.com/category-s/387.htm

You can find the parts you need here

Water is not being discharged. I have filled the reservoir that holds the carpet cleaner fluid And I have filled the water container. I know how to use the cleaner, it has always worked, But now, no water is being discharged to the carpet. I turn it on, squeeze the trigger, but nothing comes out. The wheel that is suppose to spin (to indicate that water is being discharged) is not spinning. Everything else works. I.e. the suction works, and the hand held accessories work.
ANSWER : That means that the pump belt is worn and it needs to be replaced. You can get a replacement belt and view the manual here:

Bissell Pump Belt

I have a Hoover Platinum carpet cleaner, and it has stopped dispensing cleaning agent and water. This model has a separate tank for water and separate tank for shampoo dispensing. It also has a power hand unit that dispenses shampoo. All along the hand unit has continued to dispense shampoo. Symptom #1, the water tank seemed to be taking on shampoo, as it was getting sudsy. Symptom #2 – On wash mode, nothing would come out, on Rinse mode, sudsy water would come out. Later, symptom #3 – not
ANSWER : Somewhere on the outlet is a control tap thats driven by a rubber band and something is up with this control ,best advice here is put it in the boot of the car and take iot to a hoover dealer ,they will do it seconds for you