Hoover S3330 / S3332 Straight Suction Telios Bagged Canister Vacuum\015 I have hoover model TP 6206 telios and recently it keeps swicting itself off after few seconds of operaton and starts again only to stop in few seconds! i’ve changed the bag, cleaned the filter, but in vain. would really appreciate if some one can figure out what is going on with this hoover\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

If your vacuum cleaner keeps turning off, this could be due to the following reasons: Blockages – check the hose and head for any obstructions. Filter – always check your filters, if these are clogged this could be causing the vacuum cleaner to work harder and lose suction power.
Overheating motor causing an automatic shutoff

If a vacuum motor overheats due to poor airflow, the vacuum will automatically shut off. This is most commonly caused by an air passage that is plugged by hair or dirt. Refer to the leaky hose guide to remove the hose, then inspect for hair or dirt clogs.

Overheating usually occurs because the dust bag has not been emptied, filter has not been cleaned or there is a blockage in the floor tool, wand or bent hand piece. If your vacuum shuts down unexpectedly, make sure you turn the vacuum off and unplug it from the wall socket.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
A damaged vacuum hose, clogged motor air filter or bad suction motor can cause the vacuum cleaner to shut off during use. A tripped overload on the vacuum suction motor can shut off the vacuum cleaner during use. If your vacuum has a reset button, push it; if the vacuum seems hot, let it cool off first.
The superficial causes for your VAX vacuum shutting off during use can be from blockages along the hose and body of the model. There can also be a blockage caused by a build-up of dust, dirt, hair and debris across the models` brush bar.
If there is something that has become caught in the hose in another part of the system, the airflow will be reduced and can cause overheating and a shut down. Clear out hoses, attachments, and brushes of any hair, dirt, and debris. This will allow for restored airflow and should get things going again.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
First, How long should you expect a vacuum cleaner to last? On average, According to Consumer Reports, vacuum cleaners last a median of eight years. But the lifespan varies wildly by not only brand but your own personal use. This should be expected.
Troubleshooting your vacuum cleaner`s loss of suction

1) Clogged air filter – As noted above, vacuum cleaners may use one or more air filters to trap dust and dirt as the air travels through the product. The filters can become clogged over weeks of use, reducing the vacuum cleaner`s suction.

The superficial causes for your VAX vacuum shutting off during use can be from blockages along the hose and body of the model. There can also be a blockage caused by a build-up of dust, dirt, hair and debris across the models` brush bar.
The average life expectancy of a mid-range vacuum cleaner is about six years. You can fix or replace things like blocked filters, jammed brush rolls, frayed hoses, worn-out stick vac batteries and broken accessories yourself.
NOTE: If the powerhead is blocked, the motor will switch off automatically. If this occurs, switch off the vacuum cleaner and remove the battery. Remove the blockage, and switch on the cleaner.
The average life expectancy of a mid-range vacuum cleaner is about six years. You can fix or replace things like blocked filters, jammed brush rolls, frayed hoses, worn-out stick vac batteries and broken accessories yourself.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Hoover Windtunnel On/Off switch will not turn Off…Switch seems to work O.K. when pressed directly but not with handle switch…It will turn on but not off..Cam seems to be intact on switch actuator..How does switch come out? Thanx
ANSWER : Take the handle off, then remove the tool holder, then you can get to the switch. Just has tabs on each side of switch, depress them and push it out. These switches will do this after awhile, replacing them is usually the way to correct the problem.

Hetty hoover not working. It was working ok until I opened it up to search the bag for a missing jigsaw piece and I put it all back and I hoovered the mess on the floor, then switched off and switched on and hoover would not work? Is there a cut off button on Hetty hoovers?
ANSWER : Know cut off switch, its just not getting power ? 2 things its ether at the wall plug or in side the unit. I have never found a fuse in side them , so it may be just a lose wire did you try other plugs in the house . good luck DFD

The hoover keeps switching on and off automatically.
ANSWER : Sounds to me like there is either a loose wiring in the pedal or mains power cord. Check that the plug is secure. Check both filters though – one behind the bag (usually square and slides out) as well as the main exhaust filter at the back between the power on and cord rewind button. I used to own many Telios models but they are known to have cheap shearing cords which can only be replaced by a Hoover repairer. Sometimes the On pedal can be affected as well particularly if it has been stamped on heavily..
.Dont forget to rate, ty.

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work
ANSWER : It could be the motor. I’m having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the carbon brushes wear down which is normal. However, the contact wire from the brush to its connector is set so that when the brush wears down, the wire is short enough to stop the spring etc from damaging the commutator. The end result is that you get an intermittent operation of the motor before it finally dies.
.I believe all the DYSONs come with the option of both motors and you cannot really tell which motor you have until you take the thing to bits. You also cannot change motors without changing various other parts on the hoover. On my DC 05 the writing on the YDK motor tells you which one it is.
.This website www. tasweb.org ,select the DC 05 option and scroll down tells you how to take the thing to bits. A search on google etc for your DC 07 may give similar results. Best of luck!

The switch on our Hoover Windtunnel vacuum cleaner is not working. I have located the replacement part on your website…part#Ho-28161067, I’ve removed the wires from the switch. Is there any trick to actually removing and replacing the switch itself? It seems to be in there rather tight.
ANSWER : No, follow the directions to replacing the switch and you should be good. if you got the kit then splice the wires and replace them with the wires profied and the wire nuts, you should be good.

Hoover on off switch won’t turn off. I have to unplug the vacuum to stop it. I have dismantled the handle and now I can’t get the inditation in the handle to fit over the little silver knob. I saw there was an on/off switch under the handle that is controlled by a piece of the handle.
#1 question for the manufacturer is why don’t they put the switch on the outside instead of having gimicks that turn it on and off… arghhhhhhhh
ANSWER : Don’t know what model you have, but sounds like you will need to replace the switch. As far as your question, you will have to contact the manufacture for an answer. We only provide solutions to your problem and a model number would have helped.

My Hoover Windtunnel does not clean carpet. The machine keeps grabbing the carpet. It appears that even with the switch set for carpet, the machine keeps acting as though it were set for a hard floor. How can I fix it?
ANSWER : Move the height adjustment up a little

Switch I have a kenmore 31913 vacuum and the on/off switch appears to be bad. My problem is getting into the switch. How do I open up the handle to get to the switch?
ANSWER : Go to this website.and enter your complete model number in the search field in the upper.right corner of the page. You should be able to view a parts diagram.that will provide some clues about how to disassemble the handle.