Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
The brush roll or its bearings may be clogged with hair, threads or dirt. Make sure they are clean and the roll spins. The belt may also have slipped because it was loose. Check the fit of the new belt when it is installed.
Roller brush is not spinning
Check to make sure the vacuum is switched to the correct mode. The switch should be in the Power and Brushroll mode to make the roller spin. If it is in just the power mode the roller will not move. The brushroll indicator light should be green when working.
If the roller brush is not spinning, it cannot pick up dust. One reason could be that the power button is not set to position II, which runs the roller brush. If the button does not work, here is the link to the power button replacement guide. Another reason is that the roller brush could be broken.
`Tripped` reset systems are the most common reasons for a brushbar not turning, but there are some other less common reasons too. These include: If the bearings on the end of the brushbar have seized, you won`t be able to turn it at all. This will often result in a broken belt as well, so be aware of this.
To reset the thermostat, press the vacuum`s power button into off position and unplug the vacuum. Check the vacuum for potential causes of overheating, such as clogs or a full dust cup, and allow the vacuum to set and cool off for 30 minutes before turning it back on.
Clear the brush roll of any hair and debris and inspect by placing it on its end and spin. The brush should spin freely. If it doesn`t spin; it may be time to replace.
The Shark Rotator Powered Lift-Away has one rotatory belt. The belt is responsible for the mechanical rotations of the brushroll. Without it, the vacuum will not function. The vacuum`s belt is designed to last approximately 7 years.
Next to the motor, the belt on your vacuum is just about the most important part of your vacuum. Without the belt to spin the brushroll, most vacuums won`t pick up on carpeting at all! If your vacuum uses a rubber belt, check it once a month for cracks, melting, and especially, slippage.
If you checked your brush roll, floor setting, and belt but your brush roll is still not spinning, that means you probably need a Shark micro switch replacement. This small switch tells the vacuums brush when to start spinning.
Durable – Vacuums made by Eureka are known to last for many years, maintaining the same level of quality cleaning power as the day they were first put into use.
To reset the thermostat, press the vacuum`s power button into off position and unplug the vacuum. Check the vacuum for potential causes of overheating, such as clogs or a full dust cup, and allow the vacuum to set and cool off for 30 minutes before turning it back on.
If you checked your brush roll, floor setting, and belt but your brush roll is still not spinning, that means you probably need a Shark micro switch replacement. This small switch tells the vacuums brush when to start spinning.
To reset the thermostat, press the vacuum`s power button into off position and unplug the vacuum. Check the vacuum for potential causes of overheating, such as clogs or a full dust cup, and allow the vacuum to set and cool off for 30 minutes before turning it back on.
If you checked your brush roll, floor setting, and belt but your brush roll is still not spinning, that means you probably need a Shark micro switch replacement. This small switch tells the vacuums brush when to start spinning.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
ANSWER : The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal.
Read Full Q/A … : Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would “heave” (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won’t turn. Any suggestio
ANSWER : Carpet brush won’t turn when vac on
Read Full Q/A … : Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum
Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
Read Full Q/A … : Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum
I’m using (or WAS using) a Eureka ”the boss” model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can’t find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?
ANSWER : First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes.
Read Full Q/A … : Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum
My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn’t sound right a
ANSWER : Trace the path of the suction into the tank and see if there is anything loose or ingested..Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40.
Read Full Q/A … : Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum
I have a Eureka 4870GZ. It turns on, but the brush roller doesn’t move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can’t get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there’s supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don’t see it. It looks like the motor shaft goes into a recessed place in the
ANSWER : Remove the top cover so that you can access to belt, You’ll find 2 rows of 4 decorative holes on the top cover, In two of the holes you’ll find the screws, Please use a flash light to see in that., Once the screws are removed, you’ll be able to take out the top cover. Pull the belt so that it should rotate the shaft and look for small space in between from where you can take off the old belt and new belt on. remove the agitator from its drive shaft, put new belt in, put the agitator back into place.
Read Full Q/A … : Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum
I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
Read Full Q/A … : Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum
I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn’t fall on the floor, it’s sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being
ANSWER : Even though the brush is spinning, you probably need to replace the belt
because it is stretched. It is probably slipping on the beater bar. This is normal and you shouldn’t be alarmed. There is nothing wrong with your vacuum. 🙂
because it is stretched. It is probably slipping on the beater bar. This is normal and you shouldn’t be alarmed. There is nothing wrong with your vacuum. 🙂Jim
Read Full Q/A … : Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum
