Bissell Vacuums\015 BEX BISSELL USER MANUAL FOR PRO HEAT 2X – MODEL NO. 9500-E\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

A possible cause might be that the tank is not properly seated. To assure the tank is seated properly, pick it up and re-seat is so it sits snugly on the unit. If this doesn`t fix the problem, make sure the tank is assembled properly. To make sure they are both latched properly, pick the tank up by its handle.
Your dirty water tank may not be secured tightly. Check the rubber tab on the dirty water tank and press firmly on all edges to secure it tightly. The accessory hose door also needs to be closed securely. Check the door and make sure it is locked in place.
Carpet cleaner manufacturers recommend you deep clean your carpets at least 2 times a year. If you have children, pets, allergies or smoke, you should wash your carpets with a carpet cleaner at least 4 times a year with continuous spot cleaning in between.
We recommend cleaning the same area once with the trigger pressed down, and once with your hand off the trigger. This way, you are spraying the solution into the carpet and then allowing extra suction to pull it up. The brush rolls are scrubbing out the dirt and stains the entire time.
Hot water loosens and softens dirt more quickly, making it easier to remove, and it also helps to kill bacteria. That`s why we recommend filling up your carpet cleaner`s tank with warm water. Some BISSELL Carpet Cleaners also use HeatWave technology to keep the water hot throughout the cleaning process.
ProHeat® Using the marks on the inside of the formula cap, add 7 oz of BISSELL 2X formula to tank. Add water to the tank until you reach the original formula fill line.
You`ll need it—the filter prevents dust from blowing out of the top while you`re cleaning. For wet surfaces, however, you`ll need to remove the filter entirely. Liquids will damage filters, and you could even potentially ruin your vacuum if you suck up water before removing the filter.
A: Yes it can be used as a vacuum without water.
On the average, it will take approximately 2-4 hours for carpet and upholstery to dry after being carpet cleaned. To expedite the drying process, you will want to use a fan and increase your air circulation.
Lift the tank straight up. Unscrew the cap. Decide if you`re cleaning hard floors or carpet, and fill with hot tap water to the appropriate water fill line. Then fill with the proper BISSELL formula to the appropriate formula fill line.
The BISSELL ProHeat 2X Revolution Pet Pro Carpet Cleaner is a powerful, lightweight and easy to manoeuvre carpet cleaner that achieves professional results and the powerful suction helps carpets dry in 30 minutes.
Just empty the water out of the tank after each use. Doing so will prevent leaking and extend the life of your filter.
How Often Should You Shampoo Your Carpet? You should clean your carpet at least every 12 months to remove dirt, grime, and allergens. However, this schedule can vary depending on several factors in your household. If you have children or pets, you might shampoo your carpets more regularly.
Prepare your carpet and areas to be shampooed

Begin by removing furniture from the room and then thoroughly vacuum the carpet preferably with a powerhead vacuum cleaner, before shampooing to remove loose dirt, pet hair and other particles. This should also expose the carpet stains, if there are any.

Pre-Vacuuming:

Before you begin using your Bissell Carpet Cleaner, it`s important to make sure that the surface of your carpets is free from dirt and debris. To do this, use a regular vacuum cleaner to remove any loose particles or hair before beginning your cleaning session.

The ideal temperature range for carpet cleaning is between 100°F to 150°F. At this temperature, there would be enough heat to accelerate the chemical reaction during cleaning, but it will not be hot enough to create problems with the carpet or the carpet cleaner.
Most carpets typically need 6-10 hours to dry completely.
Keep it simple. If you`re cleaning carpets to remove dirt, sand or soil tracked in from outdoors, you may not need strong solvents or cleaners to get the job done. In many cases, using plain water in your carpet cleaning machine is enough to flush out soil and dirt.
Can I use cleaning formulas other than the BISSELL brand? It`s possible to use others, but we recommend against it. Our formulas contain no dyes, phosphates or optical brighteners, and will produce optimal cleaning performance when used in combination with BISSELL carpet cleaning machines.
You don`t have to use the Bissell solution, but it is optimized for use in their machines. This means it won`t streak, leave residue, need to be rinsed, or leave buildup in your machine.
Laundry Detergents aren`t Formulated for Carpet Cleaning

Of course not! Cleaning solutions are specifically formulated to clean and not damage the machines they`re used in and the material they`re treating. Laundry soap is designed to be used in washing machines to clean clothing.

Your dirty water tank may not be secured tightly. Check the rubber tab on the dirty water tank and press firmly on all edges to secure it tightly. The accessory hose door also needs to be closed securely. Check the door and make sure it is locked in place.
A possible cause might be that the tank is not properly seated. To assure the tank is seated properly, pick it up and re-seat is so it sits snugly on the unit. If this doesn`t fix the problem, make sure the tank is assembled properly. To make sure they are both latched properly, pick the tank up by its handle.
There could be several factors as to why your BISSELL PowerFresh steam mop is not producing steam. First, check to make sure the unit is plugged in and is in a working outlet. Next, check to make sure there is water in the tank. It is very important to make sure you are ONLY using water to fill the tank.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Bissel 1698 PowerSteamer Pro Heat Plus – Manual
ANSWER : This is the link for an Adobe file for the manual.
.
.http://www.bissell.com/images/UserGuides/1698.pdf

Read Full Q/A … : Bissell Vacuums

Hello, I just bought a Bissell Powergroom (model 92L3-W) vacuum and a Bissell Proheat Pet (model 8910-3) deep cleaner and I love them both. My problem is, when we unpacked them we somehow lost the manuals; I think I had too many helpers that night – they may have gone out to the trash with the boxes. I need replacement manuals if you would be so kind as to help me out. Could you email me a manual for each of these two machines, or tell me exactly where to find them online? I’ve been looking, but
ANSWER : Follow the link below and enter the model numbers to access the User’s Guides.
.http://www.bissell.com/customer-support/

Read Full Q/A … : Bissell Vacuums

I want user manual for Bex Bissell pro heat all rounder. can it be e amiled to me
ANSWER : Follow the link below to a copy of the User’s Manual.
.http://uk.bissell.com/images/UserGuides/7700_607.pdf

Read Full Q/A … : Bissell Vacuums

Replacement electric motor for Bissell Pro Heat 2x Select carpet
ANSWER : Bissell proheat i can spray solution from the handle but it has no suction help

Read Full Q/A … : Bissell Vacuums

Operating manual i have lost my operating manual for my bissell Model #9500 proheat x2 cleaner. where can i get another manual? on one of the sites it shows that i can download the manual but for some reason i can not down load it. can you please help me with this problem?
ANSWER : BISSELL User’s Guides can be downloaded at www.bissell.com
.On the front page under Customer Service click on User’s Guides and enter the model number of your unit.
.User Guide will be displayed as a PDF file.

Read Full Q/A … : Bissell Vacuums

Need a manual for pro heat brissell model 1699
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101.
.
.reyy536

Read Full Q/A … : Bissell Vacuums

My Pro heat 2x by Bissell does not put out or **** up water Brand is Bissell. Model is 8920 12 amp
ANSWER : Please check the following with liquid in both tanks.
.

.

– Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.
.

– Check for debris on spray tips. Clean them with a soft brush (on old tooth brush works well). The spray tips may be lifted out for easier access.
.

– Ensure the tank lid is properly attached to the bottom of the tank. To attach this properly, remove the Water Tank from the machine. Hook the front window onto the lip of the bottom container and then allow the window with lid to cover the complete tank. Secure the latch on the back of the bottom tank to the back of the tank lid. THE TANK LID CANNOT BE ATTACHED PROPERLY IF THE BOTTOM TANK IS ALREADY INSTALLED IN THE MACHINE.
– Check the bottom of the Water Tank and the Formula Tank to make sure each has a red auto-load gasket attached. Make sure the Water Tank and the Formula Tank are seated properly. Depress the x on this gasket to ensure this depresses and release back out. Liquid from the tank should dispense.
.

– Remove the handle completely and re-attach. Once the handle is re-attached, re-attempt to spray.
.

.

If the machine continues to not spray, check the following:
.

REMOVE THE COLLECTION TANK:
• Make sure the unit is set to water rinse
• Remove the smart mix bottle and fill it with water only
• Place the smart mix bottle into the collection tank reservoir
• Run the unit and try to spray. If the machine sprays, you will be able to see the water level decreasing in the smart mix bottle and you will need to replace the bottom tank. It is possibly warped.
.

If these suggestions do not resolve the issue contact BISSELL Consumer Services at…
.

1-800-237-7691
Mon-Fri: 8am to 10pm ET
Sat: 9am to 8pm ET

Read Full Q/A … : Bissell Vacuums

Bissel pro heat 2x wont spray any water – Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
ANSWER : I had the exact same problem with my ProHeat 2. It would spray only through the hose attachment but not on the floor. Cleaning of the spray endings on the floor unit fixed my problem. Either soap deposits or dirt was clogging the spray endings. Here is what to do to clean up the spray endings:
.
.1. Remove the water container from the bottom unit
.2. Look up for two red plastic endings on the bottom unit
.3. Using your fingers to clip sides of an ending, carefully remove it from its slot
.4. Using pliers, release the clamp from plastic ending and remove the red plastic ending from the hose
.5. Clean the ending
.6. Put the ending back on the hose, slide clamp back on the ending
.7. Insert the ending back in its slot
.8. Repeat 3-7 for the other ending
.
.That solved the problem for me!

Read Full Q/A … : Bissell Vacuums

Hi, my name is Mea Archer, owner of the vacuum cleaner blog, the niche website that I have developed to provide the most up-to-date news, reviews and the latest advice and information for all things vacuum cleaner related.