Vaccum Bag How do I change the vaccum bag? I no longer have the booklet. I keep hearing about a zipper. I can’t find a zipper. There is sliding…

ANSWER : Slide the plastic piece off the cloth bag and open the top. Looking down into the cloth bag, you will see the old bag. It is secured to the machine near the top. You will find the cardboard collar about a third of the way down. Remove it carefull. Now, stand BEHIND the machine and put your knee against the back of the handle and taking the new bag, open the hole in the cardboard collar and insert the bag into the cloth bag and put the cardboard collar onto the handle fitting. It helps to put the lower part of the hole on first and then press the top of the collar onto the handle fitting. The idea of standing behind with your knee against the handle is so that as you attach the bag, you will be pushing against your knee which will steady the machine and allow you to use the required force to complete the action. Once completed, fold the top of the paper bag down, so that when you replace the top slider, the paper bag is NOT clamped between the cloth bag and the slider.

ANSWER : The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full bag sensor is engaged. This second switch is supposed to get reset when you push the on/off switch on the outside of the machine. The full bag shutoff switch was stiff and it, therefore, was taking a couple of presses of the on/off switch to move the shutoff switch back into the running position.

ANSWER : Try dialing the control valve to the mid way position. If the unit still shuts down with the bag full light on you have a damaged control valve under the dial on the top of the vac.
This valve failure is common in this model and can only be repaired by someone with original AERUS Electrolux repair parts, generally at an AERUS repair shop.

ANSWER : I’m assuming this is the Epic 6500 or similar model.
.Detach the hose, turn vacuum on. If it runs, place palm of hand against inport hole. If it shuts off the problem is with either the control valve setting or the control valve assembly itself.
.For cvs, turn dial on top of vacuum all the way to the largest dot, and try above test again. If that doesn’t work, then it’s the CVA. It needs to be cleaned or replaced, which is an in shop job. Fro repair, take it to the nearest Aerus Electrolux store. I recommend a full clean and service to remove any dust/dirt from the motor, fan assembly, and other internal parts.
.
.Another problem, which relates to the dial setting, is that fine dust will quickly clog the pores of the bag, resulting in the machine “thinking” the bag is full. Turning the dial to the proper setting helps get the bag fuller. The middle setting is the normal setting, and is for areas without fine dust and sand.

ANSWER : First, if it runs without a bag, there’s a problem with the bag lock-out switch or wiring. This needs to be replaced/repaired by an authorized Aerus Electrolux technician.
.
.First, turn dial on top of vacuum counter-clockwise so the smallest dot lines up with the arrow. See if it stays on. If not, detach hose and turn vacuum on. Place palm of hand over intake. If it turns off, it’s possible that the tubes connecting to the CVA are clogged and simply need cleaned. This is most often caused by using “made to fit” Electrolux bags. Dust is sucked through the bags and into the motor compartment of the machine. All interior parts get covered in dust and need to be cleaned. If this is the cause, the vacuum is best cleaned and repaired at an authorized Aerus Electrolux store. If the vacuum shuts off, or won’t turn on before placing hand over the intake, it’s probable the control valve assembly is bad and needs replaced.

Another cause is an overheated motor due to clogged screen at back of bag well, full or clogged bag, dirty afterfilter, bad wiring/connections, clogged hose, clogged power head, or bad motor. It depends largely on the type and model of cleaner. Clogged wands are also a possibility, but unlikely.

Check and clean screen at back of bag well.

Replace bag. Make sure it’s a genuine Electrolux bag made by Home Solutions.

Check and replace afterfilter if necessary. These should be replaced after every six bags.

Broken and worn wiring connections are often found in the hose ends due to abuse and normal wear and tear. You can check the continuity of the hose using a continuity tester or multi-tester. If a multi-tester, turn dial to one of the Ohm settings. Place one probe into one of the terminals on the end of the hose. This will be referred to as T1. Touch the other probe to each of the terminals/connections on the other end of the hose. These will be T3 and T4. One of them should read zero, the other should read infinity. Repeat this with the other terminal, which will be T2.

Drop a marble in one end of hose and let it roll through. If it doesn’t roll through, the hose is clogged and needs to be cleared. Plug hose into the exhaust port of the vacuum, place other end in the in port. Turn vacuum on. This provides a blowing and sucking action which should clear the hose.
Detach hose from power nozzle (PN). Drop a marble into the wand end of PN. If it rolls through, it’s clear. If not, there’s probably a clog behind the brush where the intake opening is. You may be able to reach this through wand end with needle nose pliers, or either end with a knitting/crochet needle or a bent coat hanger.

If none of these “fixes” provide the answer to the problem, it should be taken to the nearest Aerus Electrolux store for diagnosis. Repairs or checks involving disassembly of the vacuum should always be done by an authorized Aerus Electrolux service technician.

The store nearest you can be found by following the instructions at the below listed link:
http://www.aerushome.com/storelocator/

ANSWER : Sorry to hear that you are having problems with you Kenmore Magic Blue.

There is a so-called “bag full indicator”, which will only turn red if it got some major blockage. This is the reason why there is no power suction.

The “full bag sensor is just a spring mechanism that springs closed when there is a blockage. Remove the bag and look for clogs. When using it, check the bag and change it when full, not go by the “bag full indicator.”

Good luck, I hope this helps.

ANSWER : Find a piece of metal pipe with an interior diameter the size of the stem. Cut it long enough to cover the plastic fitting completely and press it over the old one. Put the upper section in position and fill the missing part with shards of wood – hammer them in place. Lastly just tape everything over.

ANSWER : Turn the knob on the top of the vacuum all the way to the right and try it again