Vacuums\015 I have an original electrolux 725 vacuum which was great up until a year ago. I had the cord fixed because it had pulled out too far and at the time the guy said something about the ball bearings. I didn’t understand at the time that I would have to replace the motor soon. It did blow up a month or so later so I had the guy put in a new motor. It had a 12 month warranty and true to form, at 13 months I decided to use a powerhead for hair in the carpet and the motor blew up and at the same time blew the fuse in my flat. Are the new motors just not as good as the originals (always seems to be the way) since the original worked for 25years without a problem then a new motor lasted just over a year or is there a good quality motor I can have fitted and if so, how much should it cost and where can I get it done? (i live on the gold coast) I love the old 725 but this is a pain!\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If your vacuum always trips the breaker, you most likely have an electrical problem. Inspect your vacuum for things like frayed or deteriorating cords. You may also notice a burnt smell when it`s running, which could indicate burning components within the vacuum itself. Replace the vacuum if you suspect problems.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
Current chopping in circuit breaker is defined as a phenomenon in which current is forcibly interrupted before the natural current zero. Current Chopping is mainly observed in the vacuum circuit breaker and air blast circuit breaker.
When vacuum interrupters are manufactured or used in field there are three tests used to validate their function :1: contact resistance, 2:high potential withstand, 3:The leak-rate test. Contact Resistance Test:A micro-ohmmeter is applied to the closed contacts of the VI and the resistance is measured and recorded.
How long do vacuum cleaners last? According to Consumer Reports, vacuum cleaners last a median of eight years. But the lifespan varies wildly by not only brand but your own personal use.
Second, can you vacuum too much? Believe it or not the answer is no. Now, if you vacuumed continually 24 hours a day, yes, that would be too much. Vacuuming every day, or even a few times a day, is not going to create any long term problems.
Failure Mode: The vacuum breaker can fail to close properly. This results in a continual steam leak as long as the steam boiler has pressure. Conversely, the vacuum breaker can fail to open. This can result in the same conditions present in old machines without vacuum breaker.
The three most common reasons circuit breakers trip are ground faults, circuit overloads, and short circuits.
– Some vacuums have an in-line thermal fuse (often located between the switch lead and the motor coil). If the fuse is blown it will need to be replaced. – Check your home circuit breaker – it may have tripped. – Some vacuums have a brushroll on/off control.
A vacuum breaker is a backflow preventer. It`s a threaded device that attaches onto a faucet. It prevents water from flowing backwards into the plumbing. Vacuum breakers prevent water from flowing in the reverse direction.
If you don`t vacuum your carpet, the dirt will break down carpet fibers and create a breeding ground for dust mites and bacteria. In addition, your home will begin to smell musty from the dirt, mites, and other organisms settling into the fibers.
For example, bedrooms and home offices should be vacuumed weekly. Areas with high traffic, such as the kitchen, living room, and children`s playrooms, should be cleaned at least twice a week. To create your ideal vacuuming schedule, experts share how often you should vacuum various surfaces in the home.
A vacuum cleaner gets power from a regular electrical socket, with the average upright design requiring between 450 and 3000 watts. However, the most often used versions use around 1400 watts, equivalent to approximately 1.4 kilowatt-hours (kWh) of electricity each hour.
It depends on what needs vacuuming. Carpeted areas that aren`t used by four-legged fur-friends should be vacuumed twice every week. Hardwood and tile need the least amount of upkeep and should be vacuum cleaned once per week.
We recommend dusting before vacuuming, this is because dust particles usually get moved around the room when you dust, meaning all your hard work will go to waste. A top tip is to wait at least 2 hours after dusting to get the vacuum out.
One to two weeks.
Give floors a good wash or steam once every couple of weeks, says Tetro. You might want to wash your kitchen floors a little more often, due to food bacteria that can spread around.
Vacuum breaker assemblies
There are two types of vacuum breakers: the atmospheric vacuum breaker (AVB) and the pressure vacuum breaker assembly (PVBA). The Water Bureau doesn`t allow either the AVB or PVBA to be used for backflow protection.
Generally speaking, about every 5 years, or as directed by the manufacturer, internal parts of your vacuum breaker should be replaced. They wear out under normal conditions and freezing temperatures also damage them.
Overloaded Circuits
The most common cause of a tripped circuit breaker is an overload in that circuit. Each circuit is only intended to carry a certain electrical load, and if it exceeds this load, it will cause the breaker to trip.
A fuse is essentially a short piece of wire of a selected diameter and composition so that it conducts current up to a certain level, but melts or `fuses` if the current rises above that level. It becomes an open circuit when it blows, interrupting the flow of current and preventing damage.
Locating a Blown Fuse
In most cases it is in the driver`s side footwell underneath the dashboard. There may also be a second fuse box under the hood. Consult your owner`s manual for the exact location of each.
A vacuum breaker, commonly referred to as a backflow preventer, is a device that prevents the potable water in your home, and possibly your neighborhood, from getting contaminated.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Vacuums
I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
Read Full Q/A … : Vacuums
Vacuum cleaner blew the fuse in my house!!
ANSWER : Are you sure that the vacuum motor went bad? If it did, then if would just have to be replace again. Doubt that you would find a different motor other then what belongs in there. If you did it would have to the right size to mount right. Some motors will last a long time while others just don’t and you never know how long a one will last. Maybe the power head is what caused your present problem.
Read Full Q/A … : Vacuums
I have a Kirby G4 Vacuum Cleaner – MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I’ve had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
ANSWER : Hello,
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci
Read Full Q/A … : Vacuums
I have a Kenmore canister vacuum – model 25614506. Some time ago, I was not able to turn the vacuum off with the on/off switch, but could still use the vacuum. Turned if off/on by pulling the plug. The other day when I went to plug it in, I heard a pop. Now the sweeper runs but the vacuum cleaner does not **** – no air flow. What could be the problem. The cleaner is only 4 years old.
ANSWER : The motor has an inline fuse
Read Full Q/A … : Vacuums
Vax upright vacuum cleaner blockage blew the fuse but now it has stopped again
ANSWER : Most motors have a thermal protector and it may have opened up. Usually it is right by the motor, connected to the motor.
Read Full Q/A … : Vacuums
My dirt devil vacuum cleaner is not working – Dirt Devil M130000 ''i'' Dual Cyclonic Upright Vacuum Cleaner Vacuum
ANSWER : Please specify whether the vacuum motor does not turn on when you flip the switch or it simply does not have suction.
Read Full Q/A … : Vacuums
Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don’t get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]
ANSWER : Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction
Read Full Q/A … : Vacuums
