Dyson DC07 Animal Bagless Upright Cyclonic Vacuum\015 A cheaper vacuum over the same area picks up more. Now brush does not work.\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

If your Dyson Ball Animal vacuum no longer sucks up dirt, dust, and debris when using the nozzle and its attachments, there may be a clog in the vacuum`s nozzle. Unplug the vacuum and use the Dyson Ball Animal Hose Replacement Guide to remove the vacuum`s hose and check for clogs at the base of the hose.
If the vacuum`s filter is full of debris, the vacuum may lose suction, causing the device to turn off automatically. Remove the filter by pulling out the purple knob labeled “filter” located at the top of the bin. Rinse the filter by running it underwater for 2 minutes.
The difference between the models becomes even more confusing when comparing their suction power, where the V7 is the weakest of the lot. It has 21 Airwatts on powerful mode and 100 Airwatts in max mode. By comparison, the V8 has 22 and 115, while the V6 has 28 and 100, respectively.
Loss of suction in your DC25, like most other Dysons, is usually caused by one of four things: Blocked or damaged filters. Splits or tears in your hosing and seals. Blockages in your ducting or.
The suction control slider is located at the front of the cleaner head. The ball located between the bin and the cleaner head.
When your Dyson no longer powers on even after charging the most likely cause is a damaged battery. This means the battery will no longer hold a charge and will need to be replaced. Once a new battery is purchased you can learn how to replace it by visiting our battery replacement page here.
Loose connections will cause your vacuum cleaner to lose suction. Make sure that the dust container, the hose, the tube and the brush are all attached properly. If the problem continues, your vacuum cleaner might have a technical problem. If you suspect this to be the case, contact an authorised service agent.
It may be full, or the machine may simply perceive it as too full to continue working. Dyson vacuum cleaners require constant airflow through them to work, and a full bin can stop this from happening. Make sure there`s no dirt lodged in the top part of the bin.
Our Verdict. The Dyson V8 is better for most uses than the Dyson V7. The V8 performs far better on bare floors, where it clears large debris like cereal with much less difficulty. It also has a longer maximum runtime and has a battery life indicator to let you know how roughly how much charge is left.
A Dyson vacuum cleaner has a lifespan of around 10 years. This is considerably longer than most other vacuums. So, if you`re looking for a high-quality vacuum cleaner that will last you for a long time, a Dyson could be a good choice. However, remember that Dyson vacuums are expensive.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
We have two possible ways of adjusting the pressure in a vacuum system: first, by changing the pumping speed (altering the speed of the pump or throttling by closing a valve); second, through admission of gas (opening a valve).
Hot environments speed up battery aging. So it`s best to avoid cleaning the car in hot weather or leaving your vacuum in rooms that experience direct sunlight for prolonged periods. The same goes for cold porches and garages in winter.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
So, the usual areas that cause suction loss include the wrong height setting, stuck rollers, a faulty gasket, a broken vacuum belt, a filled bag, or a clogged hose.
The two main indicators to determine vacuum power performance are water lift and airflow. The water lift is measured in mmH2O, mbar or kPa. It represents the suction force and is the reference parameter for vacuuming liquids and heavy materials. The airflow is measured in m3/h or in l/s.
Clog located in the vacuum hose

Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.

There are a number of possible causes of the pulsing in a Dyson vacuum – a malfunctioning power cord, battery or charger, clogged filter, damaged motor, or obstructed hose or wand.
The Dyson V7 and the Dyson Cyclone V10 are similar stick/handheld vacuums with a few differences. Thanks to its more powerful suction motor, the Cyclone V10 does a significantly better job on bare floors, and it`s a bit better on low-pile carpet.
Cylinder vacuums are typically more powerful and have a larger dust capacity, so need emptying less frequently. They also have a larger cleaning radius — the length of the cord — than upright vacuums. That`s why you`ll find the professionals use this type of vacuum cleaner in offices and hotels.
Next, you need to consider suction power. Typically expressed in Pa (pascals), this is a measurement of how powerful the motor is inside a robot vacuum. A good number to look for here is around 2,000Pa or above for an effective clean.
The Vacuum will not Stand Upright

Locate the u-bend cover, press the yellow release button, and look for any possible blockages. These blockages may be preventing the machine from locking in its upright position as well as reclining when already locked.

The DC07, released in 2001 was the first implementation of Root Cyclone technology into a cleaner.
Dyson battery life

On average, it has been seen that Dyson battery of these handheld vacuums will last for around 4 years. Generally, it is seen that lithium-ion batteries tend to wear-off after the first year of its usage, as they are limited to a few charging cycles.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.

Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.

Hello,

I am looking for a wiring diagram to install a touch/dimmer switch by “Comfort” mdl # RH-934B – Darjung Ind Ltd.
It has a standard lampcord (two wires) coming from it as well as one white, one black and one yellow wire.
The original touch/dimmer switch (no identification on it) had one white, one black, one red and one yellow – no lampcord.

Thank you very much for your help!

ANSWER : The black and the white will go to the lamp ,eg,output.The yellow is the sensor wire which should be firmly attached to the metal base of the lamp

VACUUM HAS NEVER HAD VERY GOOD SUCTION FROM DAY ONE.
ANSWER : You will need to turn it over and unscrew the plate where your beater bar is,relpace the belt and while your there clean out all lint and build up especially the intake tube.And change the bag.
.Len

Poor Suction Heya! So I just picked up a used Dyson, but when I vacuum with it, the suction is pretty weak and it spits all kinds of stuff out the back and into my feet. When I pull the hose I have good suction, but in regular mode it hardly picks up anything. The brushes are spinning, and it eventually will clean an area if I go over it again and again. Maybe a clog somewhere? Please tell me that Dysons have better suction than my $50 Dirt Devil! Thanks!
ANSWER : I recently bought a second hand Dyson DC07. Its suction was poor. I removed all the un-clipable pipe bits and to remove any blockage but it all looked clear. The Final Sponge and hepper filter did have a lot of dust in it and the rotating brush was full of hair but nothing bad.
.
.I eventual gave in to curiosity and removed the three screws in the top or the yellow removable dust collection tube and cyclone bit to see what was in there. The mechanism to release the flap at the bottom of the collection tube does not allow you to remove the lid completely but it does open far enough to get inside. I found the whole top section of the yellow plastic bit blocked by a big plug of compacted dust and a champagne cork. If you are willing to take the risk and have a torx 15 screwdriver handy it that part may be blocked. It did get a bit messy.
.
.If I was going to attempt the same procedure I’d remove the dust collection unit from the vacuum cleaner as I did before, but leave the clear tube attached and the emptying flap firmly closed to reduce the mess from the dust falling out the bottom while cleaning the top part.

Need Kirby Generation 3 Vacuum cleaner manual. Vacuum is not picking up dirt from floor. Seems to have enough suction to inflate the bag, but when you check the suction under the vacuum, there seems to be extremely litle suction.
ANSWER : If your brush roll is turning and your bag is not overly full, then the only other thing it can be is a clog where the bag connects to the vacuum. Turn the plastic part out away from vacuum and lift off to see if you have something clogging it. It would have to be something big, but not so big that it could not get past the fan. As a rule of thumb, KIRBY never clogs. I suspect that your belt is stretched out and your brush roll is not turning while on the carpet so the brush roll is just in the way rather than brushing your carpet to pick up dirt.

No suction I am getting no suction on my central vac at the vac. I do not believe that the piping is plugged up, the vacuum is not creating suction. What are the causes of no suction at the vacuum and how do I take the top half of the Nutone central vac off?
ANSWER : Use the guide at builtinvacuum.com/flowchrt.html to find the issue and solution. Most likely you need to test it without any filter and be sure the bottom of the unit is attached 🙂 To get access to the motors you need to unbolt the very top sides.

I have a Kirby G4 Vacuum Cleaner – MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I’ve had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
ANSWER : Hello,
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci