Eureka 4700A Maxima Bagless Upright Vacuum\015 Want to use the hose attached to it\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Press the dust cup release button located on the top right side of the cleaner near the handle, and pull the dust cup out of the vacuum housing.
Most pleated filters have a replacement schedule and are considered disposable by manufacturers. Paper filters should never be soaked or rinsed in water. However, some filters are made from a non-woven synthetic material (similar to a dryer sheet) that can be rinsed with water a few times to remove dust.
Most manufacturers recommend you change your filter on average every 3-6 months. However, it is recommended to change your filter even earlier depending on usage and allergy care. Most newer vacuum models use more than one filter.
Don`t be tempted to reuse vacuum cleaner bags. Your motives may be pure, but your air won`t be, and your vacuum cleaner may bite the dust (pun intended) years before its time.
Regular vacuum cleaners are not designed to pick up water and other liquids. If you are ever tempted to run the vacuum cleaner over a puddle of water, remember that you run the risk of electrocution and serious damage to the machine.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
This was my grandmothers machine and when she passed there was no owners manual so I am not sure how to use the settings on it or oil it properly. I so want to use it cause it was hers but don’t want to mess up the machine. She never even got a chance to use it before she passed away. I just have no owners manual. I know how to use sewing machines but this one is older and I don’t want to mess it up.
this was passed down to me. and a manual would help in so many ways. even if it was sent in a
May I get the manke and model # so I can help you more
My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we’ve taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can’t seem to figure out how to get in there to replace that hose….any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..
Hoover Jet and Wash 1500w S6254 001. Used once with great difficulty as assembly and use instructions are hard to follow.Now will not work as carpet shampooer at all, although assembly is correct as far as I can see and both motor and pump appear to be working and I am using the recommended cleaning fluid.Hoover website is no use at all in solving the problem.No cleaning fluid is being drawn up from the tank in to the cleaning fluid hose.There is suction from the suction hose so the problem appe
I am having the same prob my uncle got me one i cant find the manual anywhere to set it up the prob i have is where does the handle to make the water go out connect tooo ??? on the main pipe that sucks it back up i have tried every which way but not the right way obviously lol as for it not spraying mine did for all of 2 secs but think it was because i got a bit happy with the solution so gunna just try water and if its too hot it stops it spraying properly too !!
My hoover floormate h3060 has not been used for some time, when I went to use it, it would not dispense the cleaner..The last time I used it, I used a mixture of amonia and borax. I think the hose is clogged. What should I do??
You most likely have either a clogged screen at the bottom of the fill tank or the jets that spray fluid are clogged. You can unscrew them and power a paper clip through them. If the hoses are by chance clogged which doesn’t happen often, Pull one off at a time and blow real hard to unclog, then put it back on, then move to next hose.
Do NOT take all of them apart at the same time or they can get mixed up and it’s a pain to figure out how it all went back together.
Torn Hose The hose on my Dyson is torn right at the top where the the accessories connect. I was able to take the connection apart and shorten the hose, but I don’t know what to use to reattach the hose to the black fitting. It looks like it was glued…not sure what kind. Any ideas?
Hose Problem The hose broke just above the cuff on the inlet end of the hose. I found that the hose doesn’t thread into this cuff but appears to be heat bonded in some way. Can I get a replacement cuff or do I have to replace the hose?
Looks like you can just get the hose, part #38479-4, It should just screw into the adapter or it may be glued in.
Attachable hose does not want to lift up to use
Spray some oil on it to loosen it. Then rock it back and forth as pulling to remove.
How to use bissell proheat clearview 12 amps rug