Hoover Steam Vac Dual V w/ SpinScrub Vacuum\015 In our Hoover Steam Vac Dual V widepath the shampoo and clean water run continually regardless if the trigger is pulled or not. It’s unclear how the switch activates the release of shampoo and water from the tank.\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Squeeze the trigger on your cleaner to release the cleaning solution. Move the machine forward and back to suck up the dirty water. Go over the entire area with a rinse cycle once you`ve cleaned the carpet.
If the cleaner is still not spraying despite the water and detergent tanks being full, there may be a bubble of air stuck in the pump or the hose. To fix this, you need to turn the cleaner on and lower the hose down to the floor. Next, prime the pump by holding down the trigger for up to 1 minute.
First, check to make sure the clean tank has water and/or the water & formula mixture in the tank. If your tank is empty, this could be the reason your machine is not spraying. You will need to fill your clean tank again. Reseat the tank and ensure it sits snug on the machine.
A mixture of water and carpet cleaning formula is injected deep into the fibres, which softens and loosen the dirt. There are arrange of carpet cleaning formulas you can choose from – some have added fragrance, some have added stain removing properties, and some are specially designed for cleaning up after pets.
If the tank is full then water will start to leak out. Place the cleaner over a sink and pull the drainage cap out underneath the tank to drain out the water. If the tank is full then water will start to leak out. Place the cleaner over a sink and pull the drainage cap out underneath the tank to drain out the water.
Instead of using a vacuum bag, a wet and dry vacuum cleaner uses two bucket system for separating dry and wet waste. The collection chamber, and motor unit, and are the main parts of a wet and dry vacuum cleaner. The motor of the vacuum cleaner is situated on top of the collection chamber.
Regular vacuum cleaners are not designed to pick up water and other liquids. If you are ever tempted to run the vacuum cleaner over a puddle of water, remember that you run the risk of electrocution and serious damage to the machine.
The key to cleaning your carpet efficiently is to work in straight, consistent lines. Squeeze the trigger on your carpet cleaner to release the water, and push forward a few feet. Then release the trigger, and pull back over the same line.
Yes, you should keep cleaning the carpet until the water is clear. This will ensure that your carpets are clean and free of dirt, dust, and other allergens. However, you should be careful not to scrub too hard or use too much water. Doing so can damage the carpet and lead to more stains in the future.
A: Yes, you can just rinse your carpet with plain water when using the Hoover SmartWash Automatic Carpet Cleaner. Helpful?
Carpet washing

Move slowly forward with it, holding down the trigger. As you do so, the cleaning solution is released into the pile and the rotating brush bar agitates the fibres, providing deep down cleaning. Release the trigger and pull the carpet cleaner backwards over the spot you`ve just cleaned.

How Often Should You Shampoo Your Carpet? You should clean your carpet at least every 12 months to remove dirt, grime, and allergens. However, this schedule can vary depending on several factors in your household. If you have children or pets, you might shampoo your carpets more regularly.
Laundry Detergents aren`t Formulated for Carpet Cleaning

Cleaning solutions are specifically formulated to clean and not damage the machines they`re used in and the material they`re treating. Laundry soap is designed to be used in washing machines to clean clothing.

the internal hose may be kinked which will block the spray. try stretching out the hose. and giving it a few light tugs to release any kinks afterwards test to see if the machine sprays. if you still cannot get your deep clean essential to spray please visit Bissell comm to find the nearest Bissell authorized.
If you still have reduced or no spray it might mean the pump has lost its prime. To fix this, turn the power off and then back on. Wait for one minute, then depress the trigger.
Your carpet will be only slightly damp to the touch after your cleaning. Most carpets typically need 6-10 hours to dry completely. However, it could take up to 24 hours to dry depending on the time of year your carpets are cleaned, and the air circulation, humidity and temperature in your home.
Shampooers are a surface cleaner, which means they clean the upper portions of the carpet fibers but may not reach dirt and residue that settle to the bottom. Steam cleaners provide deeper cleaning, extracting with enough force to pull the dirt from the bottom of the carpet fibers.
The key to cleaning your carpet efficiently is to work in straight, consistent lines. Squeeze the trigger on your carpet cleaner to release the water, and push forward a few feet. Then release the trigger, and pull back over the same line.
Washing machine hose leaking

Tighten any parts that may be loose. Check the drain hose to confirm that it isn`t kinked or clogged. A blocked hose may be backing up the flow, resulting in standing water. You may also want to see if your drain hose is properly installed.

The key to cleaning your carpet efficiently is to work in straight, consistent lines. Squeeze the trigger on your carpet cleaner to release the water, and push forward a few feet. Then release the trigger, and pull back over the same line.
While it seems complicated, water vacuum technology is simple at its core. Basically, dirt and particles are drawn into the device, trapped in the water basin, and then run through a backup HEPA filter before venting clean air into your home. Once the dirt hits the water it is not going anywhere.
STEAM FUNCTIONThe Active Steam program will relax the creases in your clothing, allowing you to easily iron dry clothing. The Steam Refresh program will release steam after the cycle to help relax the clothing and leave less creases.
The key to cleaning your carpet efficiently is to work in straight, consistent lines. Squeeze the trigger on your carpet cleaner to release the water, and push forward a few feet. Then release the trigger, and pull back over the same line.
STEAM FUNCTIONThe Active Steam program will relax the creases in your clothing, allowing you to easily iron dry clothing. The Steam Refresh program will release steam after the cycle to help relax the clothing and leave less creases.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

I have a Hoover Platinum carpet cleaner, and it has stopped dispensing cleaning agent and water. This model has a separate tank for water and separate tank for shampoo dispensing. It also has a power hand unit that dispenses shampoo. All along the hand unit has continued to dispense shampoo. Symptom #1, the water tank seemed to be taking on shampoo, as it was getting sudsy. Symptom #2 – On wash mode, nothing would come out, on Rinse mode, sudsy water would come out. Later, symptom #3 – not
ANSWER : Somewhere on the outlet is a control tap thats driven by a rubber band and something is up with this control ,best advice here is put it in the boot of the car and take iot to a hoover dealer ,they will do it seconds for you

Water and shampoo run out with the trigger in the off position
ANSWER : From your description, you have a problem with your one of the solenoids that may be stuck open. this would require a shop repair.

No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema
ANSWER : Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn’t squirt, check for the seal at the bottom of the tank, it needs to be on the tank, not in the hole, this is for the soap bottle also, there is a seal on the bottom of it as well. The flow indictor cap is leaking air or maybe is too tight. If you had the top cover off, make sure that the tubes are routed right so as not to get pinched when the cover is put back on, the smart mix knob should be in the water setting and that the piston is on the bottom of the smart mix knob. Pump is bad. Try running a mix of vinegar and water to see if that unclogs the lines. Is the top cover and the base tight together in the back, sometimes the top breaks loose and it will raise up and it can’t spray, just re-fasten it down.
.
.Bissel’s Number is: 1-800-237-7691, they can tell you were to get service in your area.

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.

I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate
ANSWER : Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like it should. The big draw back to this model is Bissell has obsoleted all of its parts and most are no longer available. Might be wiser to buy new.

I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
ANSWER :

Call BISSELL Consumer Services.
.

1-800-237-7691
.

Mon-Fri: 8am to 10pm ET
.

Sat: 9am to 8pm ET

NO WATER COMING OUT FOR SHAMPOOING /DUMPS WATER WHEN UPRIGHT
ANSWER : There is a belt inside that runs the pump to spray the water. I would take it in a have it replaced. Mine did the same exact thing.

Trigger on hose attachment not working so water sprays constantly
ANSWER : From your description, the trigger sounds like it is stuck in the release position. this sounds like a very simple repair. The component parts need to be looked at by a service shop