o you open the darn thing to check it out
Bissell 8910 ProHeat Clear View Upright Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If the SpotBot is not turning on it may be because it isn`t on a flat surface. Place the unit on a flat surface and attach the hose of the vacuum to the bottom of the unit.
Make sure the power cord and the plug are not damaged. If either are, contact our Consumer Care team. Make sure the outlet works by plugging in a cell phone charger or small appliance. If it doesn`t work, check another outlet.
If brush will not turn by hand, or belt is broken, replace the damaged part by ordering online at BISSELL.com. Clean off any debris on the brush. If the brush is still not turning, please take the unit to an Authorized Service Center to have a Quality Technician inspect the unit.
Keep your machine clean and clean out the black valve periodically inside of the dirty water/collection tank. Empty and rinse the dirty water/collection tank after each use. To remove the tank, lift up the dirty tank latch and pull the tank out. Dump out the dirty water and rinse.
Press the recline button and lay the machine on its back. Use a flathead screwdriver to help lift the belt access door and remove. If belt is broken, gently remove it from the machine. To replace the large belt, place it over the red area of the large pulley that is toward the front of the machine.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
Check both the brush roll and chamber for any large debris that may clog or stop the brush from spinning. If it is damaged or broken, you can buy a replacement on bissell.com. Replace your brush roll by re-inserting. Using the coin again, turn the groove counterclockwise to lock the brush in place.
Vacuum Cleaner: Why doesn`t my vacuum cleaner`s brush roll spin? A broken drive belt, damaged brush roll, jammed brush roll bearings, tripped brush roll motor overload, failed brush roll motor or a wiring failure in the wand or nozzle can prevent the brush roll from spinning.
You can try using 1 cup of white vinegar in your Bissell Spot Cleaner. Pour in the Vinegar, then fill the rest of the Bissell Spot Cleaner tank with hot tap water. Just be sure to follow normal safety guidelines that go with using vinegar as a cleaner.
Luckily, changing a vacuum belt is a very simple repair on most vacuum cleaners. Vacuum owners should never have to take their machine to a shop just for a belt replacement. The first step in this (and any) part replacement is to accurately order the needed part for the repair.
Your Vacuum Has Suddenly Gotten Extra Noisy
Just like noises under your car hood, belts that are stretched to the breaking point, or that have become loose can indicate that problems are on the way.
Overall, Bissell is a popular vacuum brand for a reason – these vacuums are dependable and last up to two years without issue. However, some models are better than others when it comes to cleaning different surfaces.
Most cleaning methods simply can`t remove all the old hair, dust mites, dirt, soapy residues and chemicals. After the cleaning crew leaves, the gunk remaining in your carpeting acts like a magnet for a whole new layer of grime.
You shouldn`t need to make more than two passes with cleaning solution (especially if you pre-treated stains) when deep cleaning your carpet. Make additional passes without spray button pressed. The Rug Doctor deep cleaner has a powerful motor that will suck up and extract water from your carpet.
Carpet cleaning is the process of removing dirt, stains, and other debris from your carpet. This is important because it helps to prolong the life of your carpet and keep it looking its best. A well-maintained carpet can last for many years, but a neglected one will start to show wear and tear much sooner.
Mix equal parts hot water and vinegar and pour in your carpet cleaner`s reservoir tank. Clean your carpets as per your cleaner`s instructions. Yes, vinegar might leave a temporary pickle smell in your home but it dissipates and disappears as your carpets dry.
Carpet cleaner manufacturers recommend you deep clean your carpets at least 2 times a year. If you have children, pets, allergies or smoke, you should wash your carpets with a carpet cleaner at least 4 times a year with continuous spot cleaning in between.
You may have stalled the brush motor. To reset, turn off and unplug, then plug back in and turn on. The brush roll may have lodged debris or other entanglements keeping the brush from rotating. To fix, you`ll need to remove the brush roll to inspect.
Replace Brush Roll and turn unit ON to reset the brush. If the Brush Roll stops spinning due to debris, the LED light will turn solid red. NOTE: Make sure the Brush Roll cover tab is locked back into place to prevent breaking or faulty Brush Roll.
If the roller brush is not spinning, it cannot pick up dust. One reason could be that the power button is not set to position II, which runs the roller brush. If the button does not work, here is the link to the power button replacement guide. Another reason is that the roller brush could be broken.
Your Brush Roll has an ON/OFF Button right under the Power Button, giving you control of the Brush Roll. The Brush Roll will automatically turn on when your Adapt Ion is turned on in the stick vacuum mode. However, the Brush Roll will automatically shut off if there`s too much debris on it.
Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.
After a year or so, you may need to replace your vacuum`s beater brush. If the bristles seem to be squished, broken or are varying heights, it`s time to replace the brush. These can be found online with the vacuum`s brand and model of your vacuum cleaner.
Works in the BISSELL® CrossWave®, CrossWave® PET PRO, and CrossWave® Cordless. Easy-to-Clean and easy-to-replace brush roll. We recommend replacing your Brush Roll every 6 months for best cleaning results.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
We do not h ave the manual anymore, and the carpet wheel isn’t turning, but the belt doesn’t seem to be broken, is there another belt and how do you open the darn thing to check it out
ANSWER : Http://www.bissell.com/images/UserGuides/7901_608.pdf
Read Full Q/A … : Bissell 8910 ProHeat Clear View Upright Vacuum
I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn’t seem to turn properly and seems that it doesn’t pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt……
ANSWER : Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place..Also be sure the belt is properly installed so that the brush turns in the correct direction..If the brush is not turning or not turning in the correct direction, it will not beat the dirt from the carpet so that it can be picked up by the vacuum’s suction.
Read Full Q/A … : Bissell 8910 ProHeat Clear View Upright Vacuum
My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there’s a little thingy that should be spinning or turning….. When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI – I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn’t wet. Any tips? The manual doesn’t help.
ANSWER : You need to replace the pump belt. Here is the belt you need:
Read Full Q/A … : Bissell 8910 ProHeat Clear View Upright Vacuum
Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
Read Full Q/A … : Bissell 8910 ProHeat Clear View Upright Vacuum
Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn’t seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right….can you help. I am v
ANSWER : I’ve successfully used a compatible belt – Royal 104425001 .It’s still new, but for the time being at least – it works.
Read Full Q/A … : Bissell 8910 ProHeat Clear View Upright Vacuum
Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there’s two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it’s a ribbed belt? that is the water pump belt?
ANSWER : Just taken ours apart with the same problem… found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places – the bottom of the screw wells..This means that the water tank cannot exert sufficient pressure on the valve to release the water..Only solution is a new top cover assembly
Read Full Q/A … : Bissell 8910 ProHeat Clear View Upright Vacuum
Floor Attachment I took off my floor attachment, but now the belt seems to be off and I can’t seem to get it back on right. I can’t use the attachment and I don’t know why it’s so hard to figure this out. They say, just turn it to belt off, but when i turn it it lift’s it up and can’t line up with the belt off label. Then, when I turn it the other way, it’s off. So I’ve been trying to pull it off so when it lines up with belt off, it’s off. But the I turn it the other way and it’s still off a
ANSWER : Try this,
.
.With the floor nozzle off the machine spin the belt lifter around until the red arrows match. If you look at the side that attaches to the vacuum you should be able to see the belt up on the hook. If is not on the hook offf the machine you will never get the belt on. Once the belt is on the hook attach the floor nozzle to the front of the machine. At this point you need to spin the belt lifter back to where the green arrows match. Oh and another suggestion make sure your hieght adjuster the pedals with arrows are all the way up. Hopefully that helps you out.
.
.With the floor nozzle off the machine spin the belt lifter around until the red arrows match. If you look at the side that attaches to the vacuum you should be able to see the belt up on the hook. If is not on the hook offf the machine you will never get the belt on. Once the belt is on the hook attach the floor nozzle to the front of the machine. At this point you need to spin the belt lifter back to where the green arrows match. Oh and another suggestion make sure your hieght adjuster the pedals with arrows are all the way up. Hopefully that helps you out.
Read Full Q/A … : Bissell 8910 ProHeat Clear View Upright Vacuum
Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught on the metal pole?
ANSWER : Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)
http://64.49.205.183/v/u6451900.pdf
Read Full Q/A … : Bissell 8910 ProHeat Clear View Upright Vacuum
