Kirby Vacuums\015 I took the head off to use the att. and when i tried to put it back on the belt will not work\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

The Dyson vs. Kirby vacuum cleaners debate can be complicated, as these brands are so different. If it comes down to price or size, Dyson will probably get the upper hand — but for all other vacuuming considerations, Kirby is the way to go.
If your roller is not spinning, the first step is to remove the roller and free any debris. Refer to your model`s user manual on how to remove the roller from your vacuum head. Debris can also be left on the vacuum head it is important to also clean this area including the sides where the roller brush connects.
All Kirby vacuums use the same size belt for the brush roller. This vac belt will fit every Kirby vacuum model roller brush, including: Avalir 2. Avalir.
If too much hair, string, or lint is caught in the brushroll, the brushroll can get stuck. If the brushroll is stuck, it will put too much strain on the belt and may cause the belt to break. Remove the brushroll and clean out any debris from the bearings. After replacing the brushroll, make sure that it turns freely.
Frequently Asked Questions About Kirby Belts. Why Do I Keep Burning Belts? It is likely the belt isn`t turning freely on the brush roll.
Some of the best vacuum cleaners come with a standard attachment (like an extension wand or upholstery tool) that will help you get to those hard-to-reach spots or smaller nooks where crumbs and debris get trapped.
If the roller brush is not spinning, it cannot pick up dust. One reason could be that the power button is not set to position II, which runs the roller brush. If the button does not work, here is the link to the power button replacement guide. Another reason is that the roller brush could be broken.
Almost every time that the brush stops turning, it is because of hair wrapped around the brush roller. You will burn out the belt if you use it too long in this mode. Your only fix is to take it apart and and clean it (and cut any hair stuck in it in the process).
The suction motor creates vacuum pressure and suction by rotating a motor fan. The impeller rotates at an incredibly high speed of about 30,000 to 35,000 RPM. A suction motor`s power is measured by multiplying the rate of air flow and the vacuum pressure, which induces air flow from the brush through the hose.
Next to the motor, the belt on your vacuum is just about the most important part of your vacuum. Without the belt to spin the brushroll, most vacuums won`t pick up on carpeting at all! If your vacuum uses a rubber belt, check it once a month for cracks, melting, and especially, slippage.
If a belt is not tensioned properly, it will ride too loose or too tight on the pulley. A belt that`s too loose on a pulley will cause slippage, which leads to heat build up from friction. This heat will damage your rubber belts and cause the belts to crack and break.
It is likely that one of your ribbed or slotted pulleys has seized up causing your belt to be unable to spin. It is also possible that there may be a problem with the crankshaft drive pulley.
Kirby vacuum cleaners are made of die cast aluminum where most other vacuums are made of plastic. This makes the Kirby vacuum more durable than other model on the market. This is why the average lifespan of a Kirby is over 30 years.
Kirby vacuum prices are higher than many vacuums found at big-box stores, but that`s because Kirby vacuums are made of durable materials that will last for years. Why replace an inexpensive vacuum over and over again when you can purchase a Kirby vacuum? This complete home cleaning system that will last for a lifetime.
Kirby Vacuum Systems: Heavy-Duty Cleaning for Years to Come

If you demand the absolute best in your vacuum cleaner, you can`t go wrong with the Kirby Avalir 2. This trusted solution is built to last, so it will deliver years of deep cleaning.

If your LED flickers a lot like on the third animation you MUST change your belt immediately. If you can barely see the green LED or is permanently off change your belt immediately and book your machine for service.
Of the parts that will eventually need to be replaced in your vehicle, the serpentine belt is one of the most important. How long does a serpentine belt last? Being made of durable rubber, a serpentine belt can last anywhere from around 50,000-100,000 miles.
If an accidental jam or improper height adjustment momentarily causes the revolving brush to stop, a burn spot or a heat blister in the belt may result, causing a burnt rubber odor. In these instances, the belt is most often rendered irreversibly damaged and should be replaced immediately.
The Kirby Home Company warrants that the product shall be free from defects in material and workmanship for three (3) years from the date of purchase when the Kirby system is used for residential consumer purposes.
VACUUMING. Q: What is the N/D pedal on the back of the Kirby for? A: This is your Neutral/Drive pedal. When you are vacuuming or using the carpet shampooer in the upright position, push down the Drive (D) pedal. This activates Tech Drive® power assist to make pushing your Kirby easy.
The Dyson vs. Kirby vacuum cleaners debate can be complicated, as these brands are so different. If it comes down to price or size, Dyson will probably get the upper hand — but for all other vacuuming considerations, Kirby is the way to go.
The power nozzle is an integral part of your Kenmore canister vacuum cleaner for eliminating dust and allergens from your carpets. The power nozzles feature a motor that drives a brush roll to spins at high velocity to agitate dirt clinging to the deepest and thinnest fibers of your carpet or rugs.
Most vacuum cleaners include a small nozzle about 4″ to 6″ wide with a fairly narrow opening about 1/4″ to 3/4″ deep. This nozzle, often called the upholstery tool, is designed for cleaning upholstered furniture, window curtains and carpeted stairs.
Cleaning your vacuum after every use

For bagless vacuum cleaners, empty the dust bin, and clean the cleaning head and brush rollers. You can remove tangled hair and threads from the roller head with scissors. If the floor head has a brush roller, you can usually remove it for easy cleaning.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn’t seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right….can you help. I am v
ANSWER : I’ve successfully used a compatible belt – Royal 104425001 .It’s still new, but for the time being at least – it works.

Read Full Q/A … : Kirby Vacuums

Hoover bagless cannister 3765 – belt on power head slips off spindle. bought new belts – same problem. is this a design problem or can it be fixed? I don’t want to take it to a repair shop 100 miles away and have them just put on a new belt. saw idea of smaller belt – what number? couldn’t find suggested royal 104425001 belt.
ANSWER : I would not recommend a smaller belt. You will only wear the motor. This model series power nozzle needs to have a metal clip installed near the belt on the brush roller housing. I know that most of them left the factory without it. Remove the cover to see if one is ther. if not have your dealer send you a clip or a housing with one on it.

Read Full Q/A … : Kirby Vacuums

I’m using (or WAS using) a Eureka ”the boss” model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can’t find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?
ANSWER : First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes.

Read Full Q/A … : Kirby Vacuums

The motor on my Epic 6500 works, the hose is sucking, but the power head isn;t working… I tried the sidestep power head and that one works. Ive opened and replaced the belt and that is fine. The bulb was already burned out and wasn’t replaced so I cant tell if theres power to the head. What else could it be?
ANSWER : Connect the power nozzle directly to the hose and try.
.Check the terminals where the wand connects to the PN. If any are discolored or cracked, that may be the problem.
.Open the PN and check for loose or broken wires and connections. Repair or replace as necessary.
.The reset switch could be broken or worn out. You can check this with a continuity tester or multimeter.
.If none of these solve the problem the vacuum needs to be taken to your local Aerus Electrolux store for diagnosis and repair.
.
.http://www.aerushome.com/storelocator/

Read Full Q/A … : Kirby Vacuums

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
ANSWER : The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal.

Read Full Q/A … : Kirby Vacuums

Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!

Read Full Q/A … : Kirby Vacuums

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there’s two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it’s a ribbed belt? that is the water pump belt?
ANSWER : Just taken ours apart with the same problem… found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places – the bottom of the screw wells..This means that the water tank cannot exert sufficient pressure on the valve to release the water..Only solution is a new top cover assembly

Read Full Q/A … : Kirby Vacuums

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head.

My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt.

There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a

ANSWER : Yes, there should have been a white plastic sprocket on top of the bearing – in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail – only available by order to dealer repair shops....
Unfortunately to fix it you must send it to one and that would be more expensive than a new one. Just junk this chinese POS and buy another chinese POS.

Read Full Q/A … : Kirby Vacuums