Euro-Pro EP3005 Bagged Canister Vacuum\015 The hose on my Shark EP3005 canister split. I have searched the web and cannot locate a replacement for this model. Where can I find one?\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Yes. Shark vacuum cleaner hoses can be replaced. When looking for the right hose replacement, make sure you have your Shark vacuum cleaner model number handy. There are my different Shark models and not all hoses fit the same vacuum.
Just lift up the flap and measure the hole diameter. If your measurement is 2.5 inches, universal replacement hoses will fit! Don`t worry about your connection type! Your hose set will have either a direct connect or pigtail type.
Vacuum hoses tend to be anywhere between 3/16 inches in their inner diameter and 5/8 inches.
A selection of attachments is available for every Shark vacuum cleaner, each purposefully designed to fit a specific model, so please check the accessory is compatible with your model before purchase.
Check for a clogged hose or filter; unclog the hose and replace the filter. Wait 45 minutes for the vacuum to cool; then plug in the vacuum. Turn the power switch to the “I-On” position to start the vacuum. If the vacuum still does not start, contact Customer Service at 1-800-798-7398.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Where do I find a replacement for the hose that attaches to a Shark EP 3005 canister? The hose I have to the vacuum split.
My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we’ve taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can’t seem to figure out how to get in there to replace that hose….any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..
I have a Kirby G4 Vacuum Cleaner – MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I’ve had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
Try replacing the belt. Rubber belts stretch out after about a year.
When we turn on the vacuum, the canister falls open. The clips holding the canister in place do not seem to hold the canister tightly which I’m sure that it did in the past. The clips do not look bent, but every time we turn on the vacuum the intense pressure blows the canister open only remaining attached the the rest of the vacuum by one clip
Check filter and make sure it is kept clean at regular intervals. Possibly worn out clip retainers on cannister side due to excessive pressure build up. Do not force closure unless pressure is back to normal. May crack cannister or damage unit beyond repair.
I had the vacuum cleaner question about the canister and the wand/powerhead… the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope
Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit board in the canister – kenmore part number KC86WBZRZ000
Looks like a common fault with this particular model judging by the number of complaints on the web.
.Take it to your local vacuum repair shop and they should be able to fix it for a nominal fee.
Kenmore progressive canister bad connection from hose to canister
It could be, the female part of the connector is stretched open. You can usually insert something, like a dart, between the sleeve and the holder, to tighten it. If you paid with Pay Pal, see about getting your money back.
Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #’s anywhere online, not even partsdirect.com. any help would be great. thanks, david
Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est