Euro-Pro Shark Steam Mop – Gray/ Purple Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

The Cleaning Nozzle is clogged

Calcium and other minerals may build up in the nozzle, so you may need to clean the nozzle in order to produce steam. To do this, either use the nozzle cleaner provided with the Steam Pocket Mop, or use a straightened-out paper clip.

Tap the mop firmly on the floor a few times to get it steaming again. My mop is still not steaming. Try running a bit of vinegar through your mop. There may be a mineral build-up from your tap water.
There is condensation in the stand steamer`s hose

To solve this, lift your stand steamer`s head to straighten the hose vertically and hold your steamer in an upright position: This will allow any condensation and steam to flow again. After this, your stand steamer should steam again.

Hold down the steam trigger for about a minute to get the water circulating. You`ll be able to get the steam going in no time. If the garment steamer isn`t new, however, you may be out of water. Check the water reservoir inside of the machine and fill it up if it`s empty.
Check for a clogged hose or filter; unclog the hose and replace the filter. Wait 45 minutes for the vacuum to cool; then plug in the vacuum. Turn the power switch to the “I-On” position to start the vacuum. If the vacuum still does not start, contact Customer Service at 1-800-798-7398.
To prolong the life of your steam mop, we recommend using distilled water in the tank. Make sure you only add water to the tank – chemicals or cleaning solutions (including vinegar) may damage the steam mop and could be unsafe.
Soap only lifts dirt and oil into water, making them suspend in water. Therefore, the more soap you use, the more your mop gets saturated with dirt. So, if you do not remove all the soapy water from the floor, the dirt remains, forming streaks on the floor.
Removing limescale stains with a steam cleaner

If lime deposits are not yet very thick, they can be removed quite easily with the steam cleaner – without the need for tiresome manual scrubbing.

We have had some customers who have had their steam cleaners for 5-8 years and are still going strong. For less expensive models like the steam mops or handhelds, you should probably expect more like 3-6 years of consistent use.
The manual recommends distilled water. Water contaminants will clog the steam nozzle, which is applicable to the question about additives. Spray cleaners like 409, etc. on the extreme dirt areas of the floor or surface before steaming.
“Place the steamer at the top of the garment and gently work your way down,” recommends Sokolowski. For best results, pull down on the bottom of your garment when steaming, ensuring the fabric is taut. This way, as the fibers are steamed, they`re pulled straight and will dry into a smooth, wrinkle-free surface.
Make sure this is initially set to the highest setting – you can always then reduce the velocity of the steam as you need during use. Ensure that your water tank cap is securely fitted. The cap on most cleaner`s tanks help to maintain the pressure and seal the steam in the unit, so need to be securely fastened.
A: There is an overheat switch inside the fabric steamer that will shut down the unit if it runs out of water and isn`t turned off. But, there will be damage to the unit before it kicks in.
Due to the heat, there is a risk of dehydrating the body, and it is advisable not to spend longer than 10 minutes inside. It is also important to drink plenty of water beforehand. A steam room also provides the ideal environment for certain bacteria and germs to grow and spread.
First, attach the mop pad to the mophead, then fill the reservoir with water using the filling flask. Once the steam mop is plugged in, it takes about 20 seconds for the steam to build up, and you`ll hear the mop hissing. During the first use, I found that I had to pump the handle a few times to prime the steam pump.
Once you plug it in, it starts to heat up the water. To activate the steam, you have to pump the handle up and down. We usually started mopping instead of doing the 10 to 15 pumps because with your natural mopping motion you will pump the Shark Steam Mop each time you go forward.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

No steam My SV1000 steam cleaner will not make steam. It heats up, but I think the small portholes where the steam comes out are clogged up. Are parts available to change the steam line?
ANSWER : I used the straw to prime the lines and 50/50 mix of vinager and water and it worked perfectly. I then mixed the water container with the same mix and ran it through the system. All works fine now.

Why did my steam cleaner stoped makeing steam
ANSWER : Hi,

Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head…

Euro-Pro Shark Steam Mop Problem

Here also is a link to get any of the Shark Manuals that you need.

heatman101

,,../

For some reason, our shark steam mop stop working. Usually after I plug the steam mop, the power light would light up then you would hear & see steam coming out of the mop’s head but all of
ANSWER : HEATING ELEMENTS BURNT OUT. WILL COST OVER $100. TOFIX. SHARK NOW HAS A NEW MODEL “SHARK 3” MUCH BETTER

Shark steam blaster jr. makes steam but has no pressure
ANSWER : Yes no vinegar please. Try a product called scale clean or tablets for de-scaling coffee machines. Available from coffee machine retailers

My steam mop does not make steam.
ANSWER : How do you get a shark steam cleaner unclogged?

Steam cleaner does not get it to steam pressure
ANSWER : Scaled up temp sensor, faulty thermostat

My Europro shark steam mop won’t steam, light on but no steam.
ANSWER : Hard water deposits. I ran some white vinegar through mine, like a coffee maker, and it worked for a while, but clogged again. So I unplugged it, let it cool and turned it over in the bathtub and squirted a small amount of Lime-Away into the hole where the steam comes out. Let it soak for 5- 10 minutes and it is working like is is brand new.

Water wont come out fo the steam cleaner. – Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
ANSWER : Try adding a table spoon of salt to the water.