Bissell 1697W Powersteamer Pro Upright Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
BISSELL Carpet Cleaners use powerful suction to remove most of the water from your carpets during the cleaning process, however the carpet will be damp afterwards. To reduce the time it takes for the carpet to dry, open as many windows and doors as possible to allow air to flow through the room.
Check to see if your clean water tank is empty. The clean water tank also may not be seated properly. The brush window could also not be latched into place. Turn off your machine and check to see if the brush window is secure.
Lift the tank straight up. Unscrew the cap. Decide if you`re cleaning hard floors or carpet, and fill with hot tap water to the appropriate water fill line. Then fill with the proper BISSELL formula to the appropriate formula fill line.
A carpet cleaner is a device that mechanically applies soap and water to a carpet from a clean water tank, scrubs, and then suctions up the byproduct into a dirty water tank. Carpet cleaners work by applying and suctioning up water.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
There could be several factors as to why your BISSELL PowerFresh steam mop is not producing steam. First, check to make sure the unit is plugged in and is in a working outlet. Next, check to make sure there is water in the tank. It is very important to make sure you are ONLY using water to fill the tank.
No, this unit does not suck water.
Yes, you should keep cleaning the carpet until the water is clear. This will ensure that your carpets are clean and free of dirt, dust, and other allergens. However, you should be careful not to scrub too hard or use too much water. Doing so can damage the carpet and lead to more stains in the future.
“Most experts agree, hot-water extraction does the most complete job of removing all soils.” If carpets are more effectively cleaned using hot water, helping to protect IAQ, then one of the goals of green cleaning—protecting human health—has been accomplished.
Adding vinegar to the water in the Bissell power steam pro carpet cleaner is an easy way to make a pre-treatment for tough stains. Usually, a fourth cup is enough.
It`s really straightforward – all you need to do is sprinkle a generous among of baking soda over your wet carpet and let it sit. The baking soda not only absorbs moisture, but it`ll also absorb any nasty odours.
Air Dry the Carpet
Place fans and dehumidifiers in the room to help circulate the air and assist with evaporation. It`s best to check back every few hours to reposition the fans. If the water damage is minimal, you can speed up the drying process with the use of a hairdryer.
While extreme suction power may offer peace of mind to homeowners who want to feel confident that their vacuums are effective at sucking up dirt and germs, it can be very damaging to your carpet and should be avoided! For high pile and premium soft carpet, be sure to avoid vacuums with concentrated or sealed suction.
Check the dirty water tank and make sure there are no clogs in the hose below it. Remove the filter and clean debris from both the screen and filter. Also empty the dirty water tank and leave the filter out to dry completely before replacing it.
Just Hot Tap Water
You can always clean up most of the mess with hot tap water. Then come back later with the proper Bissell cleaner, if needed.
Designed to easily clean carpet, upholstery, stairs, area rugs, auto interiors, and more. Large-capacity, 3/4-gallon tank allows you to clean more area without emptying and filling the tank.
Factory reset on a Wi-Fi Connected Roomba® and Braava jet®
e Series Robots: Press and Hold the Home and Spot Clean and CLEAN button down for 20 seconds then release. 900 Series Robots: Press and Hold the Dock and Spot Clean and CLEAN button down until all LEDs illuminate.
There is condensation in the stand steamer`s hose
To solve this, lift your stand steamer`s head to straighten the hose vertically and hold your steamer in an upright position: This will allow any condensation and steam to flow again. After this, your stand steamer should steam again.
check the cap of the water tank to make sure it is correctly and securely attached to the water tank. check your water tank to make sure it is securely and correctly fitted in to the body of the garment steamer – incorrect placement of the water tank can block water from feeding in to the body and boiler of the steamer.
Naturally, all carpet cleaners will leave some moisture, which will dry out in the hours following the cleaning process. However, if the carpet remains wet long after cleaning, it`s because the final step of that process was insufficient.
Carpets that still look dirty or have stains reappear after cleaning is a result of something called wicking. This is due to over wetting the carpet, the backing, and pad which causes them to return back to the surface once dry.
If the carpet or rug was wet for more than 48 hours, regardless of the source of the water, general EPA/FEMA/CDC guidelines recommend removal and replacement.
Don`t let water linger on carpet, even if it`s just a little bit. Mold grows fast, and water can quickly soak through and damage the pad and subfloor. Don`t forget the pad. “Any carpet that has padding should be lifted,” says Diana Rodriguez-Zaba, president of ServiceMaster by Zaba, a certified carpet cleaning company.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.
Read Full Q/A … : Bissell 1697W Powersteamer Pro Upright Vacuum
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Bissell 1697W Powersteamer Pro Upright Vacuum
I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
Read Full Q/A … : Bissell 1697W Powersteamer Pro Upright Vacuum
I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
ANSWER :
Call BISSELL Consumer Services.
.
1-800-237-7691
.
Mon-Fri: 8am to 10pm ET
.
Sat: 9am to 8pm ET
Read Full Q/A … : Bissell 1697W Powersteamer Pro Upright Vacuum
We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet – HELP!!!! We’re read and reread the manual and contacted customer service and received no help.
ANSWER : First things first. It’s only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected under warranty.
.
.Otherwise, The jets on this unit clog easily, there are two of them and you can locate them under the recovery tank towards the front of the machine, and blow them out with an air compressor. To prevent the jets from clogging in the future make sure to flush all shampoo out of the machine with clean water when done using it. That is most likely your problem.
.
.If it is leaving black streaks on your carpet it could be coming from a burnt belt or melted brushroller part, in which case inspect the belts and brushrollers and replace the damaged pieces.
.
.I hope this helped
.
.Good Luck
.
.Otherwise, The jets on this unit clog easily, there are two of them and you can locate them under the recovery tank towards the front of the machine, and blow them out with an air compressor. To prevent the jets from clogging in the future make sure to flush all shampoo out of the machine with clean water when done using it. That is most likely your problem.
.
.If it is leaving black streaks on your carpet it could be coming from a burnt belt or melted brushroller part, in which case inspect the belts and brushrollers and replace the damaged pieces.
.
.I hope this helped
.
.Good Luck
Read Full Q/A … : Bissell 1697W Powersteamer Pro Upright Vacuum
I have a Kirby G4 Vacuum Cleaner – MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I’ve had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
ANSWER : Hello,
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci
Read Full Q/A … : Bissell 1697W Powersteamer Pro Upright Vacuum
I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate
ANSWER : Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like it should. The big draw back to this model is Bissell has obsoleted all of its parts and most are no longer available. Might be wiser to buy new.
Read Full Q/A … : Bissell 1697W Powersteamer Pro Upright Vacuum
My Bissell Pro Heat Select 2X does not pull up the dirt from the carpet into the water. The water just slowly disappears. The first time I used it the water got really dirty. The very next time I used it it worked differently and the water just disappeared until it was all gone. I’ve only used it a couple times and I don’t see where it is working. Has anyone else had this problem?
ANSWER : Inside the plastic suction lid is a little red plastic filter that has to be cleaned out every time you use it because it sounds like your vaccum is not picking up all the hair and debri before you clean the carpet causing the water to be injected into the carpet and disappearing and not filling the tank with dirty water. Steve
Read Full Q/A … : Bissell 1697W Powersteamer Pro Upright Vacuum
