Karcher DE4002 Steam Vacuum\015 Hi, I have recently had my karcher 501 vapour rapid steam cleaner’s tank replaced. I have used it trwice with no worries, now the low water indicator light light comes on as soon as I turn it on. The tank is full. Also the middle light that indicates the machine is ready to use does not come on at all.Please help as I am sick of throwing service money away again and again.Thanks\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
What should I do if the steam cleaner does not heat up? Check the power cord and fuse, as well as the thermostat and pressure switch. Top up the water. If the water shortage light does not go off, please consult one of our service partners or contact us directly.
First, check to make sure the unit is plugged in and is in a working outlet. Next, check to make sure there is water in the tank. It is very important to make sure you are ONLY using water to fill the tank. Other solutions may cause breakdown of the gasket and/or other parts of the machine.
Some steam cleaners come with descaling agents. In addition, there are a variety of descalers out there for use in steam cleaners, humidifiers, and other home appliances where water is vaporized. Whether you are using a descaler you purchased or making your own from simple baking soda and water, cleaning is the same.
What Can Go Wrong with a Steamer? The electrical cord may need replacing. The heating element or resistor may be faulty. Switch contacts or other appliance controls may become dirty.
check the cap of the water tank to make sure it is correctly and securely attached to the water tank. check your water tank to make sure it is securely and correctly fitted in to the body of the garment steamer – incorrect placement of the water tank can block water from feeding in to the body and boiler of the steamer.
Fill the base with white household vinegar (5 %) so that the heating element is just covered. Put the steam accelerator in place. Close the appliance, connect it to the mains and set the time to 15 minutes. Should there still be a layer visible after the 15 minutes are over, repeat the procedure.
After you let your steam mop`s tank soak, plug it in, turn it on, and give it time to get hot. Once it builds up enough steam, pull the trigger and allow the device to spray with the vinegar in the tank. As the steam shoots out, it should help clear out a blocked nozzle while also removing any other buildup inside.
Fill the Tank With Vinegar: Fill the water tank with distilled white vinegar or cleaning vinegar. Allow the vinegar to sit in the tank for at least 30 minutes (up to two hours is best) to help break apart the limescale and mineral deposits. Expel the Vinegar: Turn on the steamer and choose the highest heat setting.
What Should I Use? Good quality tap water. If you don`t have issues with hard water stains and buildup, your tap water is good.
A steam cleaner works on the same principle as a pressure cooker – water is heated in a sealed boiler until it boils, creating steam. This takes between one and six minutes per litre of water, depending on the device.
Steam cleaners work by using low pressure steam (up to 150psi) and very high temperature steam (up to 360 deg F), which kills just about all bacteria, mold, and allergens that it passes over. The heat loosens dirt by breaking down the fibres which as a result makes it far easier to wipe off.
High-temperature 145˚C pressurised steam enables fast dry times and more hygienic results than other steam cleaners on the market.
Thanks to their size, travel steamers also heat up quite fast. Once they`re plugged in, they`ll be ready for use in two to three minutes.
If the device isn`t producing steam, please try the following: Check for any debris or blockages in the head and main body. Empty and refill the tank. Check for any limescale/debris in the tank itself and descale if necessary.
If you have an elevated wire cooling rack, that can also be used in place of a proper steamer. Use it exactly how you would a steamer basket: add an inch of water to a pot with a tight fitting lid, place the wire cooling rack in the pan, and place the food on top of the rack.
Steam cleaning can remove tough stains on synthetic carpets. It can also deeply clean the carpet. Hot water extraction is better for carpets that are made out of natural fibers. Steam cleaning can cause the carpet fibers to shrink.
A steam cleaner works on the same principle as a pressure cooker – water is heated in a sealed boiler until it boils, creating steam. This takes between one and six minutes per litre of water, depending on the device.
Heat-up time: Heat-up time on most steam cleaners is relatively short. Most models offer a heat-up time between 25 seconds and 8 minutes, though some cleaners can take up to 12 minutes to heat.
Warm-up time: Some heat up in under a minute, so you don`t have to turn the machine on and wait. Tank size: The more water it holds, the longer you can clean before stopping to refill and reheat. Devices with “continuous fill” come with a backup tank to keep you cleaning longer.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Green light wont go on and mop wont heat up
ANSWER : Hi,
Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head…
Euro-Pro Shark Steam Mop Problem
Here also is a link to get any of the Shark Manuals that you need.
heatman101
jjjh
Read Full Q/A … : Karcher DE4002 Steam Vacuum
My bissell proheat carpet cleaner wont turn on. Its plugged in and everything but wont turn on. I’ve had it for a few years but its always worked before. Do they have to heat up if I haven’t used it in a while?
ANSWER : Hi,
Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.
Bissell Proheat Upright Wet/Dry Vacuum Problems
heatman101.
.
.agsf
Read Full Q/A … : Karcher DE4002 Steam Vacuum
Wont make calls wont receive calls wont send or receive sms
ANSWER : Hi. Can you tell me what brand and make is the mobile phone?
Read Full Q/A … : Karcher DE4002 Steam Vacuum
I have a bissell pro heat and it wont dispense water. the little red thing wont spin and it looks like the belt doesn’t move. within a few minutes you smell it getting hot.
ANSWER : Hi,
Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.
Bissell Proheat Upright Wet/Dry Vacuum Problems
heatman101.
.
.hgrt
Read Full Q/A … : Karcher DE4002 Steam Vacuum
My Bissell Pro-Heat 2x 12 amps
Model 9200-2
The rollers wont turn and the water wont release
Model 9200-2
The rollers wont turn and the water wont release
ANSWER : WON’T SPRAY ???
Read Full Q/A … : Karcher DE4002 Steam Vacuum
I have the euro steam blaster s3325 when I turn it on, the steam ready **** comes on right away not heating can the heating element be replaced? thanks
ANSWER : There is a device attach to the heating element called a thermo fuse, this devise brakes down when it get to hot.
open the machine and replace it with the same value. it is written on it..
open the machine and replace it with the same value. it is written on it..
Read Full Q/A … : Karcher DE4002 Steam Vacuum
I have a bissell pro heat water wont come out
ANSWER : The water sprayers on your Bissell are probably clogged. I had this problem this morning, myself, with my machine, about 15 months old. They get clogged up with mineral deposits. This is a *fairly* easy thing to fix yourself. Read all the way to the end before trying this fix.
.
.Unplug the Bissell. Remove the water container pieces from the top of the base. You’ll probably reveal two red plastic pieces mounted in the Bissell’s base, about .75″ x .75″. These spray water on your brushes when you press the water-and-soap trigger at the top of the Bissell’s handle. These water sprayers tend to clog. See the metal spring running up the hose, behind each red water sprayer? As you squeeze the red plastic sides of one red water sprayer, use a screwdriver or other tool under the spring to wedge up the hose, to release the sprayer from its mount in the base. Stick a finger in the hole of the base of the Bissell where the sprayer was mounted and run it around the edges there including on the underside of the base to clean out any gunk you can find. Clean any gunk you can off the red water sprayer with an old toothbrush.
.
.Now you need to remove the water sprayer from the hose. You need a pair of pliers. Use the pliers to squeeze the brass colored clip that is keeping the red water sprayed mounted to the end of the small hose there. Move the clip down the hose so it compresses the spring and is no longer on the red plastic water sprayer. Now you can twist and pull the red water sprayer out of the end of the hose. You’ll need a little hand strength to do this. Just be careful not to break the water sprayer by using a tool. They’re not particularly delicate, but breaking one would render your Bissell useless until it was replaced, so use a little care.
.
.When you’ve removed a red water sprayer from the hose, put the outer end of the red water sprayer in your mouth and seal your lips around it, and try blowing through it. You can’t blow air through it, right? It’s clogged. Open up a paper clip and push it back-and-forth through the small hole in the end of the water sprayer back towards its middle. You’ll probably push out a line of white mineral deposits. Clean them off the water sprayer with the old toothbrush, and try blowing through the water sprayer again. If air passes through clearly, you’ve fixed it. Now you have to put it back together. Push the water sprayer back on the end of the hose. Use the pliers to reposition the brass clip on the end of the hose over the water sprayer. Push the red water sprayer back into position in the base of the Bissell.
.
.Now do the same for the other red water sprayer.
.
.I had a problem when I fixed this on mine this morning, because when I pulled one water sprayer off, the hose advanced up under the spring and I couldn’t reattach the red water sprayer, because it couldn’t reach the end of the hose. So try to use the brass clip or some other means (rubber band, tape, another clip) to keep the hose from crawling up inside the spring after you pull the red water sprayer off the hose. If the hose gets up under the spring anyway, despite your best efforts, I fixed this by removing the six screws on top of the Bissell base (the surface of which the water tank mounts on top of), and then pried it up. You can pull out the hose, reattach the red water sprayers to the hoses, position the hose *very carefully* inside the base (there are mounts under there they need to fit into, so you don’t break anything), push the red water sprayers through the mount holes and mount them, and then reattach the screws to the base.
.
.There’s something else you may need to do that can help get the water flowing. This one’s easier. The Bissell uses pumps, which need to be primed. Sometimes an air pocket inside the machine keeps water from flowing. To prime the pumps, separate the two water tank pieces. Fill the base as usual and mount it on the Bissell without the top water tank piece. Plug the Bissell in and **turn it on**. (The Bissell must be running to do this.) Kneeling on the floor in front of the Bissell, reach up and press the soap and water release trigger at the top of the Bissell’s handle and hold it in as if you wanted water to go through. On top of the water tank is a plastic grommet hole about 1 inch in diameter, through which you pour water to fill the tank. Seal that hole with the flat of your hand. You’ll feel a bit of suction. Lift your hand up and down a few times. Release the trigger and repeat a few times. Now that you’ve cleaned out your water sprayers and primed the Bissell’s internal pumps, I’m hoping water will GUSH through your Bissell once again.
.
.As you probably have learned the hard way, as I did, it’s VERY important to do a lot of cleaning of the Bissell after each use, more than the manual tells you to do. Clean the bottom of the unit. Empty all the water. Thoroughly rinse out both water container pieces. Unscrew the three clear plastic pieces, one in front, two on the sides, that surround the brushes, and rinse them thoroughly in water. Clean off the brushes and all the lint and gunk around and above the brushes. (A water spray bottle and toothbrush are helpful here.) Tip the machine and blow all the water out of the hole in the base. Release the red clip springs on the red water sprayers and blow on them. Doing this will slow the failure of the Bissell. It’s a great little machine for the money, but it does have a learning curve and need more pampering than a vacuum cleaner, doesn’t it??
.
.Good luck!
.
.Unplug the Bissell. Remove the water container pieces from the top of the base. You’ll probably reveal two red plastic pieces mounted in the Bissell’s base, about .75″ x .75″. These spray water on your brushes when you press the water-and-soap trigger at the top of the Bissell’s handle. These water sprayers tend to clog. See the metal spring running up the hose, behind each red water sprayer? As you squeeze the red plastic sides of one red water sprayer, use a screwdriver or other tool under the spring to wedge up the hose, to release the sprayer from its mount in the base. Stick a finger in the hole of the base of the Bissell where the sprayer was mounted and run it around the edges there including on the underside of the base to clean out any gunk you can find. Clean any gunk you can off the red water sprayer with an old toothbrush.
.
.Now you need to remove the water sprayer from the hose. You need a pair of pliers. Use the pliers to squeeze the brass colored clip that is keeping the red water sprayed mounted to the end of the small hose there. Move the clip down the hose so it compresses the spring and is no longer on the red plastic water sprayer. Now you can twist and pull the red water sprayer out of the end of the hose. You’ll need a little hand strength to do this. Just be careful not to break the water sprayer by using a tool. They’re not particularly delicate, but breaking one would render your Bissell useless until it was replaced, so use a little care.
.
.When you’ve removed a red water sprayer from the hose, put the outer end of the red water sprayer in your mouth and seal your lips around it, and try blowing through it. You can’t blow air through it, right? It’s clogged. Open up a paper clip and push it back-and-forth through the small hole in the end of the water sprayer back towards its middle. You’ll probably push out a line of white mineral deposits. Clean them off the water sprayer with the old toothbrush, and try blowing through the water sprayer again. If air passes through clearly, you’ve fixed it. Now you have to put it back together. Push the water sprayer back on the end of the hose. Use the pliers to reposition the brass clip on the end of the hose over the water sprayer. Push the red water sprayer back into position in the base of the Bissell.
.
.Now do the same for the other red water sprayer.
.
.I had a problem when I fixed this on mine this morning, because when I pulled one water sprayer off, the hose advanced up under the spring and I couldn’t reattach the red water sprayer, because it couldn’t reach the end of the hose. So try to use the brass clip or some other means (rubber band, tape, another clip) to keep the hose from crawling up inside the spring after you pull the red water sprayer off the hose. If the hose gets up under the spring anyway, despite your best efforts, I fixed this by removing the six screws on top of the Bissell base (the surface of which the water tank mounts on top of), and then pried it up. You can pull out the hose, reattach the red water sprayers to the hoses, position the hose *very carefully* inside the base (there are mounts under there they need to fit into, so you don’t break anything), push the red water sprayers through the mount holes and mount them, and then reattach the screws to the base.
.
.There’s something else you may need to do that can help get the water flowing. This one’s easier. The Bissell uses pumps, which need to be primed. Sometimes an air pocket inside the machine keeps water from flowing. To prime the pumps, separate the two water tank pieces. Fill the base as usual and mount it on the Bissell without the top water tank piece. Plug the Bissell in and **turn it on**. (The Bissell must be running to do this.) Kneeling on the floor in front of the Bissell, reach up and press the soap and water release trigger at the top of the Bissell’s handle and hold it in as if you wanted water to go through. On top of the water tank is a plastic grommet hole about 1 inch in diameter, through which you pour water to fill the tank. Seal that hole with the flat of your hand. You’ll feel a bit of suction. Lift your hand up and down a few times. Release the trigger and repeat a few times. Now that you’ve cleaned out your water sprayers and primed the Bissell’s internal pumps, I’m hoping water will GUSH through your Bissell once again.
.
.As you probably have learned the hard way, as I did, it’s VERY important to do a lot of cleaning of the Bissell after each use, more than the manual tells you to do. Clean the bottom of the unit. Empty all the water. Thoroughly rinse out both water container pieces. Unscrew the three clear plastic pieces, one in front, two on the sides, that surround the brushes, and rinse them thoroughly in water. Clean off the brushes and all the lint and gunk around and above the brushes. (A water spray bottle and toothbrush are helpful here.) Tip the machine and blow all the water out of the hole in the base. Release the red clip springs on the red water sprayers and blow on them. Doing this will slow the failure of the Bissell. It’s a great little machine for the money, but it does have a learning curve and need more pampering than a vacuum cleaner, doesn’t it??
.
.Good luck!
Read Full Q/A … : Karcher DE4002 Steam Vacuum
My mini steam zapper heats but produces no heat
ANSWER : You should get steam in the amount of time it take to boil water
Read Full Q/A … : Karcher DE4002 Steam Vacuum
