Hoover U6630-900 WindTunnel Bagless Upright Vacuum\015 I have the same problem. My wind tunnell wont shut off unless I unplug it.\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

If a vacuum motor overheats due to poor airflow, the vacuum will automatically shut off. This is most commonly caused by an air passage that is plugged by hair or dirt. Refer to the leaky hose guide to remove the hose, then inspect for hair or dirt clogs.
A thermal cut off is a heat-sensitive device that automatically disconnects the power to a vacuum`s motor when the operating temperature exceeds a safe value.
Check For Clogs or Blocks In The Vacuum

Check the hoses, the filters, and throughout the vacuum, and clean out any blockages or clogs. Vacuums will likely also have a recommended cooldown time to ensure that the vacuum won`t overheat. You will need to wait for that time before you turn the vacuum back on.

Why won`t my power unit shut off? Make sure the unit is in the Auto mode and that there is not a hose plugged into a wall valve. Unplug the low volt wire at the side of the unit, if the unit continues to run, the relay in the pc board is faulty and the entire pc board needs to be replaced.
How Vacuum Switches Work. Once the switch registers a change in the negative pressure based on the preset sensitivity of the setpoint, the diaphragm of the switch will open or close the attached circuit, turning off or powering on a device. Vacuum switches can be used with NO and NC states.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
THE PROCESS OF VACUUM COOLING EXPLAINED

This process takes away energy in the form of heat from the product, which ensures rapid cooling, normally within 15 – 30 minutes for most products.

The filters are clogged

These will find their way into all parts of the vacuum cleaner and clog up the filters, preventing them from working properly. This will also have an impact on the motor`s ability to cool, making it operate less efficiently and possibly causing it to overheat and produce a burning smell.

A vacuum cleaner can run continuously for 30 – 60 min each time. The vacuum cleaner has no suction power. For example, a hair cannot be sucked up.
When a central vacuum continues to run without a hose plugged into a vacuum wall port then there is a short in the system. Be sure to unplug the central vacuum unit to stop the vacuum from running and then follow these steps to determine where the short is and what to do about it.
Clear out hoses, attachments, and brushes of any hair, dirt, and debris. This will allow for restored airflow and should get things going again. Make sure there are no cracks or broken belts impeding the system from running optimally.
Simply plug the product back in or restore the power and then switch off the appliance using the button on the control panel. The door will now unlock.
Stick Vacuum Not Running

First make sure you have charged your device. If the vacuum still will not turn on after that, try to unplug the vacuum charger from the outlet. Leave the charger unplugged for at least 1-2 minutes. Next, turn on the stick vacuum and let run until the battery completely drains.

A strong odor from the shellac that coats the copper coil windings is an indicator that the motor is about to or has burnt out. If the motor is still running, even if it turns on and off by itself as it is heating and cooling, you can still run the motor until it gives up for good.
There are basically only 3 reasons a vacuum sealer bag will fail: The seal line area was dirty/wet/wrinkled when the bag was sealed or made (if made from a roll). Something in the bag punctured the bag. The bag is defective.
The pump needs to running the entire time to keep the vacuum at the fullest level.
If you don`t vacuum your carpet, the dirt will break down carpet fibers and create a breeding ground for dust mites and bacteria. In addition, your home will begin to smell musty from the dirt, mites, and other organisms settling into the fibers.
Yes. The battery is designed to be left on charge permanently, and this will ensure that the vacuum is fully charged when it`s next used. Once the battery is fully charged, your machine won`t use any more electricity and will enter a standby/idle state.
If your Henry feels hot to touch or is overheating, it may need a filter change.
Overheating due to clogged exhaust filter

The exhaust filter can also get clogged, causing a problem with the motor cooling. Therefore, you should also check the exhaust filter if the vacuum cleaner smells burnt. It is usually located on the top or back of the unit, right where the exhaust air comes out.

The temperature of an object is usually defined as the average kinetic energy of its constituent particles, and since a vacuum has no constituents its temperature would be zero under this definition.
The water exposed to the vacuum undergoes flash evaporation: part of the water evaporates, taking its heat of evaporation from the remaining water, thus cooling it.
Water Can Ruin Your Vacuum Motor

If water invades the motor, you may have a completely failed vacuum cleaner. Again, not only will the water be inside your motor, but it will be carrying dirt and grime with it, making it unlikely (or at least very difficult) to restore the motor to a safe condition.

If your vacuum cleaner keeps turning off, this could be due to the following reasons: Blockages – check the hose and head for any obstructions. Filter – always check your filters, if these are clogged this could be causing the vacuum cleaner to work harder and lose suction power.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My nutone cv556 wont shut off
ANSWER : It sounds like the relay is bad. This website has a pretty good trouble shooting page.

https://www.centralvacuumstores.com/cvs/trouble_help.php#wont_turn_on

I have a hoover windtunnel upright vacuum, It will not shut off and I have to unplug it to do so. If I take apart the upper handle and manually flip the internal switch it works just fine, only when using the external switch on the handle, wont shut off.
ANSWER : This is a common problem with this machine. The switch has too much resistance to be turned on and off with the switch button and rod. If you put in a new switch, ( # 28161075 ), your problem should be fixed.

I have an easy flo vacuum model # 199C and it won’t shut off. It started out as an intermitent problem but now will not shut off when the hose is unplugged, nor when the off/on switch on the main unit is shut off. the only way to get the motor to stop running is to unplug the unit. Any ideas?
ANSWER : Just had this same problem. I unplugged the low voltage signal wires and the vacuum stayed on. Thus eliminating the possibility of the signal wires shorting out somewhere. I’m not really sure which wire(s) were causing the problem. But when I disassembled the top housing to expose the motor and wiring it seemed to work just fine. My theory is that the heat of the motor caused the insulation on a wire to melt which was then shorting somewhere inside the housing. I suggest removing the motor housing before buying any parts or calling easy-flo. If you’re lucky like me then your vacuum should be running again in a matter of minutes.

Filters have been clogged with wet cat litter and now the vac will turn on but shuts off and wont cont to vaccume. can we clean/rinse the filter out. filter light has come on and then turns off once the vac shuts down.. thanks
ANSWER : Using a vacuum cleaner for wet cat litter??? Not a good idea at the best of times! The machine’s cutting out because it’s overheating. You don’t tell us the make or model of your machine – some filters are washable, many are not. Your user manual should tell you. As a general rule, cloth- or sponge-type filters are probably washable, paper ones are not. If you do wash the filter, give it at least 24 hours in a warm place to dry thoroughly before re-using.

My vacuum cleaner will run for a few minutes and then shuts off. The plug light on the panel blinks. I thought the motor was shut, but after a long time it will turn on again, but again, only for a few minutes and then shuts off again. Any ideas? I bought an Oxygen Ultra a few years ago, but I don’t like it nearly as much as the old Epic.
ANSWER : I know nothing about your particular vacuum, but many vacuum cleaners these days have
.safety cut out’s, which causes the motor to do exactly what you describe. Sadly blockages, faulty switches, over stretched cables, carbon brushes etc could also give similar symptoms, so sounds like a job for the repairer on this occasion. Get a quote first if you can.

My eureka enviro vac shut off and wont turn back on it was clogged but does not smell burnt . is there a reset or some kind of shut off when it gets clogged?
ANSWER : Same thing happened to me. I checked the owner’s manual and it turns out the Eureka Envirovac has a built-in thermal cut-off switch. So anytime the motor gets too hot, it just shuts down. Most of the time this is because it gets plugged or the filter is too dirty. In my case, the dust basket thingy and filter were clogged beyond belief. Probably would help to clean that more regularly in hindsight. Supposedly it will turn back on after the recommended 30 minute wait.

Wont make calls wont receive calls wont send or receive sms
ANSWER : Hi. Can you tell me what brand and make is the mobile phone?

Wont shut Off
ANSWER : Its the power switch, hoover has had that problem for years. I’d take it to a vac repair shop, sometimes the wires that connect to the switch get burnt as well and should be replaced.