Dyson DC07 Bagless Upright Cyclonic Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If your dyson vacuum isn`t turning on, don`t panic – there are a couple possible causes. It could simply be that the vacuum overheated and shut itself off. If that is the case, wait 24 hours and turn it back on. However, another problem with dysons are failed power switches.
To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on.
If you find that your machine is turning off intermittently, the filter in your vacuum is most likely full and covering the ventilation system. Remove the filter, then empty and wash it. Allow the filter to dry for at least 24 hours, or until it is completely dry.
If your vacuum`s brush bar is not turning, the bar may be clogged from hair and other debris. Ensure that the brushbar button, which is gray and located next to the power button, is turned on. If this is not the issue, then the brushbar itself may be damaged or stuck.
If your Dyson vacuum no longer powers on even after it has been charged, the vacuum`s battery may be damaged. If the battery is damaged, it will no longer hold a charge and will need to be replaced. Use the Dyson DC58 Battery Replacement page for instructions on how to replace the vacuum`s battery.
When your Dyson no longer powers on even after charging the most likely cause is a damaged battery. This means the battery will no longer hold a charge and will need to be replaced. Once a new battery is purchased you can learn how to replace it by visiting our battery replacement page here.
Check the LED light to determine the battery level. A solid blue light indicates that the machine is in normal operating mode. A flashing blue light indicates that there is no power, and the battery needs to be charged for a minimum of 3.5 hours.
If your vacuum cleaner keeps turning off, this could be due to the following reasons: Blockages – check the hose and head for any obstructions. Filter – always check your filters, if these are clogged this could be causing the vacuum cleaner to work harder and lose suction power.
If there is a strong burning smell coming from the motor area of your Dyson DC14 or DC07 then it is most likely that your motor has burnt out.
Check for a plugged hose:
Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.
Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.
A solid blue light indicates that the battery is charging. Flashing blue light indicates that the battery is not charging. Re-fit the charger or try another socket.
Over time, all batteries are subject to degradation. So if your run time has declined when the machine is not in Max / Boost mode, it might be time to buy a new battery. All our machines come with a 2-year initial warranty that includes the battery.
3 cleaning modes Power button Press the power button to start cleaning. Lean to clean Lean handle back to start a clean. Leave upright to direct suction to the wand. The wand or tools are attached to the end of the hose.
If you checked your brush roll, floor setting, and belt but your brush roll is still not spinning, that means you probably need a Shark micro switch replacement. This small switch tells the vacuums brush when to start spinning.
Resetting your HEPA filter life Press and hold the Night mode button on your remote control. The display on your machine will countdown from five, the filter life will be reset and your machine is ready to use. Resetting your carbon filter life Press and hold the Oscillation button on your remote control.
If the filters are not attached correctly, a triangle warning may show on your screen. If this happens, please reattach the filters securely.
Yes, The battery does not overcharge-just like all the other battery operated tools available on the market. Sorry, there was a problem.
Dyson battery life
On average, it has been seen that Dyson battery of these handheld vacuums will last for around 4 years. Generally, it is seen that lithium-ion batteries tend to wear-off after the first year of its usage, as they are limited to a few charging cycles.
Overheated Motor
If your vacuum was working fine and then suddenly shut off, it may have overheated. Most vacuums are equipped with a thermal protector safety switch that won`t allow the motor to run when it becomes overheated. You will need to wait for 30 minutes to 2 hours, depending on your machine, to try again.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
I would not use with filter off. This must be a feature of the newer models. This one blows air even with the filter removed. The suction is reduced by a considerable amount.
We recommend replacing your air purifier filter every 12 months. That`s because over time, filters can get clogged with pollutants, and even let unpleasant odors back into the room.
A strong odor from the shellac that coats the copper coil windings is an indicator that the motor is about to or has burnt out. If the motor is still running, even if it turns on and off by itself as it is heating and cooling, you can still run the motor until it gives up for good.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Won’t start I was Sweeping & the Blanket Cornor got caught. Now the sweeper won’t start
ANSWER : Did you verify that the switch did not get moved to BARE FLOOR rather than CARPET. If it is not on CARPET the brush will not spin.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
When I turned on the sweeper it would not start. I put a different power cord on it and it worked fine. now it won’t start but the light on the brush and the bag full will flash when i turn it on and off but it wont start. i have 2 of these doing the same thing. do you have any idea what could be wrong. I have checked for clogs but have found none. Bob
ANSWER : Its sounds to me like the computer board inside the machine has gone bad. Keep in mind that the filters in these machine do need to be replaced regularly to keep the vacuum working correctly. Any good vacuum shop should be able to fix your problem. Reguardless of what they might tell you there these really are one of the best machines on the market and definatly worth having repaired.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
While using my Dyson a rug got caught and that ratcheting sound started. I removed all signs of strings, etc until the brushes rotated fine but when I started the Dyson the ratcheting started again. I have the DC 14 Animal.
ANSWER : The rattly sound means the drive belt has snapped or the protective clutch has slipped. This needs repair by someone who knows how to repair Dysons officially. Sadly its the kind of model that can’t be done by the owner.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Chain saw starts runs, bur saw won’t start next time it is needed, craftsman chain saw
ANSWER : Steam vacuum? no clue but on your chain saw make sure you check the choke. it would explain why it wouldn’t start again.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Problem starting Sometimes will not start at all. Sometimes will do a quick start and stop. Other times it starts and runs fine????
ANSWER : This can happen if you have an intermittent short in your cord. Try plugging it in and then wiggling the cord around where it goes into the body of the vacuum with the switch set to “on.” (If you’re not sure whether it’s on or off, just click it back and forth occasionally.)
.If the motor kicks on there’s a short, which usually requires a cord replacement. If that’s the case, it’s a relatively simple fix for most dyson models.
.If not, you could have a short in your switch or somewhere else in the electrical system of the machine.
.
.-R
.If the motor kicks on there’s a short, which usually requires a cord replacement. If that’s the case, it’s a relatively simple fix for most dyson models.
.If not, you could have a short in your switch or somewhere else in the electrical system of the machine.
.
.-R
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.
ANSWER : Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does, then problem solved, if not let me know and we can try something else and you can send a picture or video to me of the problem.
Let me know how this works out for you.
Benjamin
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
I have a Dirt Devil Vacuum that won’t start up anymore. It was working, but then it stopped. The tube got clogged up. Now the tube is unclogged and empty and it won’t turn back on. It’s also hot on the bottom of it. Help?
Blown fuse or what?
ANSWER : Some of the Dirt Devils have a reset button on the back, near the bottom. But if the it is getting hot on the bottom, that may mean the motor is trying to run but can’t. Maybe something has jammed it. You would have to disasemble it to find out.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Pull Cord I was trying to pull the cord to start the leaf blower and it got stuck all the way out and won’t go back in. Now I can’t start it.
ANSWER : CHORD STUCK , NOW FIXXED BUT METAL SPRING CAME OUT, WHEN WOUND BACK, HOOW DOES IT ATTATCH TO PLATIC COWL AGAIN?
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
