Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum\015 Model number 1697-1\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Check your hose for any cracks or holes that can cause loss of suction. You may also have a clog in the lower hose. Pull down and at an angle to disconnect. A clog in the main hose could also be the problem.
1-8 of 8 Answers. No. It uses the solution to clean but does not suck it up.
Check the dirty water tank and make sure there are no clogs in the hose below it. Remove the filter and clean debris from both the screen and filter. Also empty the dirty water tank and leave the filter out to dry completely before replacing it.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
What`s happening with your vacuum cleaner is that a clog has built up and debris being agitated by the roller is spitting out or stirring up dust without sucking it in.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
What`s happening with your vacuum cleaner is that a clog has built up and debris being agitated by the roller is spitting out or stirring up dust without sucking it in.
The most common cause of loss of suction is that the filters have become blocked. They may require cleaning or replacing. Another cause could be that the vacuum cleaner hose is blocked.
Inspect the vacuum hose for any small holes, kinks, or cracks. Any cracks or holes will decrease the amount of suction in the hose and will not allow the carpet extractor to properly remove liquid from the floor. The hose will need to be replaced if there is damage.
So, the usual areas that cause suction loss include the wrong height setting, stuck rollers, a faulty gasket, a broken vacuum belt, a filled bag, or a clogged hose.
Low compression, an intake leak or tight valves also can cause low vacuum at idle. If the vacuum reading fluctuates within the normal range-the gauge needle bounces around a lot-uneven compression (broken rings or leaking valves or head gasket in one or two cylinders) is a likely culprit.
Similarly, portable carpet extractors can be repaired but after five to seven years, replacing the machine with a new portable should be considered. While it can vary significantly depending on use, a commercial vacuum cleaner should last three to five years before it may need to be replaced.
Vacuum massage is a non-invasive mechanical massage technique performed with a mechanical device that lifts the skin by means of suction, creates a skin fold and mobilises that skin fold.
First, check that the cord is properly connected to the vacuum cleaner (again, this is surprisingly easy to overlook) and that there are no splits in the rubber. If the cord is damaged, it will need immediately repairing or replacing. The on/off switch can break over time and need replacing.
Don`t let water linger on carpet, even if it`s just a little bit. Mold grows fast, and water can quickly soak through and damage the pad and subfloor.
Overall, Bissell is a popular vacuum brand for a reason – these vacuums are dependable and last up to two years without issue. However, some models are better than others when it comes to cleaning different surfaces.
What`s happening with your vacuum cleaner is that a clog has built up and debris being agitated by the roller is spitting out or stirring up dust without sucking it in.
Why Is My Concrete Floor Always Wet? Subfloor moisture problems have two sources: humidity from the air and dampness from the ground. In both cases, the issues are exacerbated by warm air, which is why people in warmer climates may notice this problem more often.
If you`re wondering whether you can use the Bissell Crosswave without water, the answer is yes!
The BISSELL portable and handheld carpet washer are wet extraction models only. Please do not use as a dry vacuum. If you use as a dry vacuum, you may damage your deep cleaner and void your warranty.
Yes, it is safe to leave cleaning formula in the clean tank when not in use.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema
ANSWER : Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn’t squirt, check for the seal at the bottom of the tank, it needs to be on the tank, not in the hole, this is for the soap bottle also, there is a seal on the bottom of it as well. The flow indictor cap is leaking air or maybe is too tight. If you had the top cover off, make sure that the tubes are routed right so as not to get pinched when the cover is put back on, the smart mix knob should be in the water setting and that the piston is on the bottom of the smart mix knob. Pump is bad. Try running a mix of vinegar and water to see if that unclogs the lines. Is the top cover and the base tight together in the back, sometimes the top breaks loose and it will raise up and it can’t spray, just re-fasten it down.
.
.Bissel’s Number is: 1-800-237-7691, they can tell you were to get service in your area.

My sunbeam water cooler model #YLR2-5-67H3 has been sitting unplugged for 3 years. I moved, plugged it in and put a water bottle on top and water went all over the floor. I unplugged it, (read the instructions on the front, duh) and it still leaks on the floor. What should I do?

I put it over the sink, emptied it, checked the drain plug, tried running a glass full of tap water through each tap. Only the room temperature one would work.

ANSWER : One of the rubber connecting hoses inside it has dried and aged so the pressure of the water from the bottle made it burst....
You will need to open it, find the defective hose and replace it – a 2 hour relatively easy job. The hardest part will be in taking the casing apart – lots of hidden screws.

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.

Flap My floor/ tools knob won’t turn. The knob controls wheather you are going to use tools to shampoo furniture of floors. The flap and knob will not trurn
ANSWER : Most likely the diverter valve is broken part #2136988. You will have to remove the top to replace it.

I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate
ANSWER : Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like it should. The big draw back to this model is Bissell has obsoleted all of its parts and most are no longer available. Might be wiser to buy new.

Won’t suck up water from floor
ANSWER : Lay the machine on its back. Look at the 1″round clear spiral pipe uptake assembly..Mine spit open after 2 or 3 years of use and would not suck up (not with that 1″ OPENING HA HA ).yOU NEED THE WATER UPTAKE ASSEMBLY for $15 bucks..Try at this site.http://order.store.yahoo.net..Hoover FloorMate Water .HO-59177042 $14.99 Fis = H3000.Channel / Hose Assembly

I HAVE A BISSELL PROHEAT CARPET CLEANER 7920 I DISSEMBLY IT TO CLEAN IT. I DON’T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT’S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON’T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT’S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 .
.dfjddj

I am using a hoover steam vac and the button keeps popping up to say that the water is full. That makes the thing stop sucking up water out of the carpet. Problem is, it has barely sucked up any water yet. Help!
ANSWER : Have u tried cleaning it out really good make sure any areas that water is **** up through are free of hair, lint ect.