Zanussi 7294 Vacuum baglessThe cylinder is not turning and then it cuts out
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If your vacuum cleaner keeps turning off, this could be due to the following reasons: Blockages – check the hose and head for any obstructions. Filter – always check your filters, if these are clogged this could be causing the vacuum cleaner to work harder and lose suction power.
If your vacuum cleaner has lost suction power, it`s time to empty the container. Vacuum cleaners come with various foam or mesh filters. These might get clogged over time if not cleaned or replaced properly. This will cause your vacuum to lose suction.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
The most common reason for vacuum motors failing is overheating. Most `dry` vacuums have a flow-though motor. These motors use the air they have sucked up the dust with, to cool themselves. When there is a blockage, flow-though motors are unable to cool themselves due to the lack of airflow.
A strong odor from the shellac that coats the copper coil windings is an indicator that the motor is about to or has burnt out. If the motor is still running, even if it turns on and off by itself as it is heating and cooling, you can still run the motor until it gives up for good.
The average life expectancy of a mid-range vacuum cleaner is about six years. You can fix or replace things like blocked filters, jammed brush rolls, frayed hoses, worn-out stick vac batteries and broken accessories yourself.
The most common problem with a vacuum cleaner is also the easiest to remedy: clogs in the hose or attachments. Also the electrical cord, motor, switch, fan, brushes, and motor bearings can all need repair or replacement. The drive belt may need replacing; and the attachments, hoses, and filters may need unclogging.
Overheated Motor
If your vacuum was working fine and then suddenly shut off, it may have overheated. Most vacuums are equipped with a thermal protector safety switch that won`t allow the motor to run when it becomes overheated. You will need to wait for 30 minutes to 2 hours, depending on your machine, to try again.
Vacuum System Failures:
Reduces or eliminates effectiveness of the turn coordinator, attitude indicator, and heading indicator. Discovered by a low indication on the vacuum gauge or unusual instrument indicators. When the primary air inlet is blocked, the backup inlet automatically opens due to pressure.
As a general rule, if the repair is going to cost less than half the cost of a new vacuum cleaner, it`s best to go ahead and get it repaired. When the service tops half the price of a new machine, it`s probably best to invest in a newer model.
There are varying degrees of quality and value when it comes to vacuums; if you paid a lot for the appliance, repairs are likely worth it, but we recommend that you don`t spend more than half of the original price for any repairs.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
For bagless vacuum cleaners: Remove and clean the dust bin/canister. If possible, wash it in warm water. You may be able to remove and wash the hose, wand and accessory heads too, if they`re very dirty.
How Often to Empty the Vacuum Canister. Yes, the chart says to empty the vacuum`s canister after every few uses, but that`s at the very minimum. Rather than waiting for the canister to fill up all the way, the Vacuum Experts suggest you empty it after every use.
If all your filter needs is a good cleaning, though, rinse it under warm water until it runs clear, then gently wring out the excess water and set it aside to dry. Finally, use the can of air duster to remove excess dust from inside the vacuum.
If you don`t vacuum your carpet, the dirt will break down carpet fibers and create a breeding ground for dust mites and bacteria. In addition, your home will begin to smell musty from the dirt, mites, and other organisms settling into the fibers.
Most vacuum makers recommend cleaning or replacing filters at set intervals—and those intervals vary wildly. Tineco, for example, recommends cleaning the filters on its stick vacuums after every few uses, while Miele says you need to change its vacuum filters only after every fourth bag change.
Sweeping at night is bad luck
“In ancient times, when there was no electricity, brooming at night with minimal lighting might also sweep away expensive items like rings, earrings, and chains out of the house,” he says.
We recommend dusting before vacuuming, this is because dust particles usually get moved around the room when you dust, meaning all your hard work will go to waste. A top tip is to wait at least 2 hours after dusting to get the vacuum out.
Most cleaning experts will tell you to vacuum your floors once or twice a week depending on how much foot traffic those floors are getting. Cotter says that high-traffic areas should be vacuumed twice weekly, as these areas have a higher level of dirt, and vacuuming this frequently will prevent matting.
If your vacuum always trips the breaker, you most likely have an electrical problem. Inspect your vacuum for things like frayed or deteriorating cords. You may also notice a burnt smell when it`s running, which could indicate burning components within the vacuum itself. Replace the vacuum if you suspect problems.
It`s Losing Suction
A vacuum cleaner that is in good working order should have excellent suction and be able to clean up everyday dust and debris from around your home with ease. If you notice that your vacuum is starting to lose suction, it could be a sign that you are due for a replacement.
A typical price for Vacuum Belts is $6 but can range from approximately $4.99 to $26.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I have a Kenmore canister vacuum – model 25614506. Some time ago, I was not able to turn the vacuum off with the on/off switch, but could still use the vacuum. Turned if off/on by pulling the plug. The other day when I went to plug it in, I heard a pop. Now the sweeper runs but the vacuum cleaner does not **** – no air flow. What could be the problem. The cleaner is only 4 years old.
ANSWER : The motor has an inline fuse
Read Full Q/A … : Zanussi 7294 Vacuum bagless
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Zanussi 7294 Vacuum bagless
I have a Kirby G4 Vacuum Cleaner – MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I’ve had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
ANSWER : Hello,
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci
Read Full Q/A … : Zanussi 7294 Vacuum bagless
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would “heave” (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won’t turn. Any suggestio
ANSWER : Carpet brush won’t turn when vac on
Read Full Q/A … : Zanussi 7294 Vacuum bagless
I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn’t fall on the floor, it’s sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being
ANSWER : Even though the brush is spinning, you probably need to replace the belt
because it is stretched. It is probably slipping on the beater bar. This is normal and you shouldn’t be alarmed. There is nothing wrong with your vacuum. 🙂
because it is stretched. It is probably slipping on the beater bar. This is normal and you shouldn’t be alarmed. There is nothing wrong with your vacuum. 🙂Jim
Read Full Q/A … : Zanussi 7294 Vacuum bagless
I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
Read Full Q/A … : Zanussi 7294 Vacuum bagless
Electrolux Epic 6500SR Full Bag sensor working, Does not Reset properly
ANSWER : The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full bag sensor is engaged. This second switch is supposed to get reset when you push the on/off switch on the outside of the machine. The full bag shutoff switch was stiff and it, therefore, was taking a couple of presses of the on/off switch to move the shutoff switch back into the running position.
Read Full Q/A … : Zanussi 7294 Vacuum bagless
I purchased a Eureka C4910 last year and have a question that I am hoping you can answer.
There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth.
The beater bar motor turn-on mechan
ANSWER : Good day!
Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.
When the motor and the belt is OK the problem could be on electrical wiring and switch.
If found electrical switch burned out you need to replaced it because when the switch is burn the contact of that switch is open even you turn it ON.that’s why the motor is not function because the voltage is not pass through the circuit because of open switch.You need to replaced it.
And check some fuses if any and other burned electrical wire.Replaced it also.
Thank you and don’t forget to rate my answer.
Read Full Q/A … : Zanussi 7294 Vacuum bagless
