Kirby Ultimate G Bagged Upright Vacuum\015 Hello, I just purchased a used kirby ultimate g and the manual and the video are not here. I would like to vaccum bedding and curtains ect. But do not know how the hose attaches? I have tried taking off the main nosel hookes to the bag but do not understand if I put the hose on there, where the dirt will go. Plz help. Confused\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Use the upholstery attachment on mattresses and fabric surfaces. Work in a horizontal or vertical motion from top to bottom. Use the crevice tool in the tight corners and seams. Use the dust brush on leather furniture to reduce any risk of scratching.
Use the upholstery attachment on mattresses and fabric surfaces. Work in a horizontal or vertical motion from top to bottom. Use the crevice tool in the tight corners and seams. Use the dust brush on leather furniture to reduce any risk of scratching.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Please help us with as simple and complete instructions as possible.
THANK YOU VERY MUCH,
LOUIE CAPLAN
Remove the outer cloth bag by rotating the bottom boot AWAY from the side of the main unit. Put the tank where the bag was, line up the notch (or may be a small arrow) on the tank with the notch on the Kirby near the hole. Set the tank down onto the Kirby and rotate it toward the Kirby to lock it on.
To remove the Kirby power nozzle, go to the front of the machine and turn the belt lifter clockwise until the red arrows line up. Turn the latch at the top to release the nozzle and take it off.
Make sure that the GREEN arrows on the hood’s belt lifter are lined up. Put the shampooer hood onto the tray, covering the shampooer brush and splash guard. The belt lifter should be FACING the hole in the center of the tray. While looking into the large hole in the rear of the shampooer hood, turn the belt lifter slowly and “hook” the belt with the belt lifter. Continue to turn it until the RED arrows on the top or the belt lifter line up. This stretches the belt to it’s highest position, preparing it for attachment to the main unit. This action also binds the hood to the tray. It may be a bit hard to turn, as the belt may be stiff if the shampooer isn’t used often.
Attach the shampooer assembly to the Kirby in the same manner as the power nozzle. (Put the little hooks on the hood onto the outside edges of the bar in the front, push it toward the Kirby and lock it on)
Now, turn the arrows back to green matching green. This will position your belt onto the drive shaft and make the nozzle ready to shampoo.
Lower the front of the Kirby to it’s lowest setting. You may raise it up one click if you have thick carpeting. Either one is fine.
Now, all that’s left to do is attach the tank to the tray using the hose. One end goes on the tank shampoo outlet which is located near the on off valve. The other end “pops” into the hole in the center of the tray.
Turn the Kirby on, turn the foam setting to “on” and lay the foam out onto the carpet by pushing FORWARD QUICKLY and BACKWARD SLOWLY. The foam is ONLY being laid out onto the carpet when the machine is going BACKWARD and wastes into the front tray when going forward, so going forward quickly uses less shampoo for the same job. The quantity of foam being deposited to the carpet is controlled by the speed of the backward movement. The slower you go, the thicker the foam.
Lay the foam out in strips, overlapping the edges a bit for good coverage. For tough stains, try going over the area in two different directions when laying the foam in that area. Don’t go over an area too many times though…it will get too wet and can cause a thick build-up of carpet protecter and soap. Pick up the foam by turning the shampoo valve back to “off”. Simply run the shampooer slowly and smoothly over the foam and it will pick it up and deposit it into the tray in the front.
Once you get the feel for the foam laying process, you should be able to do a whole room without emptying the tray. Make sure that you transition from forward to backward slowly and smoothly, especially as the tray fills up with dirty water. Jerky movements will cause the funk to slosh back out onto the clean rug.
PERSONAL ADVICE>>> I like to lay the foam in 3′ to 4′ square blocks and then pick it back up before moving on to the next area. This prevents the foam from being spread over too large an area. If it takes you too long to pick the foam up, it may dry out a bit and won’t do as good a job as when it’s fresh and damp.
Now that you’ve gotten this far, I imagine that you’re enough of a veteran to detach the shampooer and reassemble the vacuum. My advice in this area is for the shampooer cleaning process. Make sure that you release the belt from the hook by turning the belt lifter to GREEN before trying to seperate the hood from the tray. If you don’t do this, you’ll never get them apart.
If this guide was helpful to you,Thank you!
.
.http://stores.ebay.com/CLICK-HERE-FOR-GREAT-DEALS_KIRBY-OWNERS-MANUALS_W0QQcolZ4QQdirZ1QQfsubZ7656839QQftidZ2QQtZkm
.
.Hope this helps!
Looks like the switch went bad (Switch HERE)
We have instructions for replacing it too.
The “funny noise” with hose throws me off a bit though. Check if there is nothing in the hose (put a nickle through it).
Good Luck
I have online manual for attachments HERE
Good Luck
.Marci
.
.this site has instructions with pictures
.
.Hope this helps!!
.
.http://reviews.ebay.com/KIRBY-CARPET-SHAMPOOER-INSTRUCTIONS-MANUAL-DIRECTIONS_W0QQugidZ10000000004594992
.
.Hope this helps,
.Marci