Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum\015 Please help i don’t what to do with my kenmore progressive direct drive, does it take a belt? why does it have no more suction, hapened after i changed the bag.\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Check service panel for tripped breakers/blown fuses. If breaker is tripped, reset it. If fuse is blown, replace it. If vacuum cleaner is plugged in, be sure power button is in the off position before resetting breaker/changing fuse.
Loose connections will cause your vacuum cleaner to lose suction. Make sure that the dust container, the hose, the tube and the brush are all attached properly. If the problem continues, your vacuum cleaner might have a technical problem. If you suspect this to be the case, contact an authorised service agent.
Vacuum cleaners are fairly simple machines. They need power to be transmitted to the vacuum to create a suction force that lifts debris. So, the usual areas that cause suction loss include the wrong height setting, stuck rollers, a faulty gasket, a broken vacuum belt, a filled bag, or a clogged hose.
Most people don`t realize the importance of cleaning and replacing their vacuum filters. But your vacuum is just like any other appliance in your home, it requires maintenance. If the filter isn`t clean, it can impact the performance of the vacuum.
If the motor filter (located below the bag) is dirty, hand wash with soapy water. Rinse with clear water, squeeze out excess water, and allow it to dry completely before returning it to the vacuum. Insert a new dust bag and close the cover.
How long do Kenmore vacuums last? A. It`s suggested that the typical vacuum can last up to an average of eight years. With proper maintenance, a Kenmore vacuum could last that long or longer.
The bottom line. Many vacuum brands recommend changing the bag before it becomes full, at least every three months.
CFM is the the speed of the air flow. CFM equates to a car`s top speed. Suction Lift is the measurement of the vacuum`s ultimate power. This can be compares to a car`s horsepower.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
All vacuum cleaners operate based on air flowing from the opening at the cleaning head or tool, through the vacuum cleaner and the bag and/or filter system and then out the exhaust port. This airflow is created by the vacuum motor, which also may be referred to as the suction motor.
Boil old suction cups to revive them.
Take the pot off of heat and drop your suction cups in for about 30 seconds. Take them out with a pair of tongs and pat them dry on a lint-free towel. Try to use the suction cups right after you dry so they`re still warm and flexible.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
Rinse the filter
Any fine dust remaining in the filter can usually be removed with a gentle rinse under a cold tap – hold the filter under the running water until the water runs clear. You shouldn`t need to use any detergent – just water.
HEPA filters are not designed to be washed and reused. Doing so will cause damage to the fibers which makes the filter ineffective and it will become void of its job. Once a filter has reached the maximum capacity of harmful particles, it will need to be replaced with a fresh, new one.
Product Details: Made of premium materials, with H12 filtering effect, it can improve the working efficiency of the vacuum cleaner. PLEASE NOTE: Our filters are not washable and cannot be squeezed.
It is important to check your vacuum filter regularly and replace it when necessary. A clogged air filter will decrease the suction power of your vacuum cleaner and make it less effective at removing dirt and dust from your home.
A good rule of thumb is to replace the main filter every 3 to 5 years or when you see vacuum performance drop to an unacceptable level.
One caveat: Handling this vacuum`s 23 pounds takes some muscle. In our member survey, Kenmore canisters earned a very good score for predicted reliability and an average rating for owner satisfaction.
Several things cause a burning smell, such as a motor part is that broken or worn out, the motor is running too hot, you suck up a burning cigarette, or the rubber belt has snapped. The belt helps turn the brush roller that helps guide dirt and debris into the vacuum.
Bagged vacuum cleaners tend to lose their suction as the bag starts filling. Even if they lose suction, these vacuum cleaners can find their clog easily.
Neglect your vacuum filter bags, and you`ll swiftly lose suction power. This, in turn, places unnecessary strain on your vacuum`s motor. Eventually, your vacuum will become a lot more difficult to maneuver, not to mention less effective at cleaning your rugs, carpeting, or other surfaces.
Suction pressure should be kept at less than 200 mmHg in adults. It should be set at 80 mmHg to 120 mmHg in neonates.
What is a Good Suction Power for a Vacuum Cleaner? An upright cordless vacuum cleaner should have at least 100 air watts to effectively clean a variety of floor surfaces, with the best Samsung vacuum cleaner reaching up to 210W*.
Next, you need to consider suction power. Typically expressed in Pa (pascals), this is a measurement of how powerful the motor is inside a robot vacuum. A good number to look for here is around 2,000Pa or above for an effective clean.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
No Suction The suction of the vaccuum has stopped. We haven’t had the vaccuum for very long and the bag has been recently changed. Both the floor vaccuum and the hose are not picking anything up. I’m not sure what the problem could be.
ANSWER : Your Power head is blocked with hair or dirt,,or the hose which connects the Upright with the power head is blocked.
Try taking a steel coat hanger apart (straighten it out) and then push it into the pickup hose to remove blockage.
Try taking a steel coat hanger apart (straighten it out) and then push it into the pickup hose to remove blockage.
Read Full Q/A … : Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
No suction I am getting no suction on my central vac at the vac. I do not believe that the piping is plugged up, the vacuum is not creating suction. What are the causes of no suction at the vacuum and how do I take the top half of the Nutone central vac off?
ANSWER : Use the guide at builtinvacuum.com/flowchrt.html to find the issue and solution. Most likely you need to test it without any filter and be sure the bottom of the unit is attached 🙂 To get access to the motors you need to unbolt the very top sides.
Read Full Q/A … : Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
Suction Cover The suction cover of my Eureka Deep Steam 2575A is broken – the tabs snapped off of the cover so I am unable to screw the suction cover back on. I need to purchase a new suction cover but can’t find one anywhere. Anyone know what I can do? thanks
Decreased suction was using to vaccuum carpet and suction decreased..nothing plugging hose….suction remain at unit canister and exhaust is fine….suggestions??
ANSWER : You might have a clog, to try and unclog the lines, you need to unplug the unit, and remove the bag compartment. Then take a shop vac using the hose attachment hold it into the attachment door where there is low suction and try to draw the clog out the way it went in.
Read Full Q/A … : Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
Lost suction my DCO7 lost suction in the hose I started taking it apart and cleaning it and looking for clogs (probably more than I should have) and when I put it back together it has awesome suction in the hose but no suction in the base. It just pulls the pine needles up (christmas tree) but they never appear in the “bag” compartment and when I look they are just all gathered in a clump in the bottom by the brush.
ANSWER : Hi.
.
.Remove the sole plate turn the 3 plastic screws to unlock & lift off.
.
.Now remove the blockages that have accumilated from the oppening of short clear hose.
.Check you can turn brush roller & check belt.
.
.Now reassemble switch on pull handle back & look under machine is brush spinning ?
.
.If not check the knob on side of machine is in drive (D) position.
.
.http://dysonmanuals.llc.nu
.
.Chris..
.
.Remove the sole plate turn the 3 plastic screws to unlock & lift off.
.
.Now remove the blockages that have accumilated from the oppening of short clear hose.
.Check you can turn brush roller & check belt.
.
.Now reassemble switch on pull handle back & look under machine is brush spinning ?
.
.If not check the knob on side of machine is in drive (D) position.
.
.http://dysonmanuals.llc.nu
.
.Chris..
Read Full Q/A … : Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
Poor Suction Heya! So I just picked up a used Dyson, but when I vacuum with it, the suction is pretty weak and it spits all kinds of stuff out the back and into my feet. When I pull the hose I have good suction, but in regular mode it hardly picks up anything. The brushes are spinning, and it eventually will clean an area if I go over it again and again. Maybe a clog somewhere? Please tell me that Dysons have better suction than my $50 Dirt Devil! Thanks!
ANSWER : I recently bought a second hand Dyson DC07. Its suction was poor. I removed all the un-clipable pipe bits and to remove any blockage but it all looked clear. The Final Sponge and hepper filter did have a lot of dust in it and the rotating brush was full of hair but nothing bad.
.
.I eventual gave in to curiosity and removed the three screws in the top or the yellow removable dust collection tube and cyclone bit to see what was in there. The mechanism to release the flap at the bottom of the collection tube does not allow you to remove the lid completely but it does open far enough to get inside. I found the whole top section of the yellow plastic bit blocked by a big plug of compacted dust and a champagne cork. If you are willing to take the risk and have a torx 15 screwdriver handy it that part may be blocked. It did get a bit messy.
.
.If I was going to attempt the same procedure I’d remove the dust collection unit from the vacuum cleaner as I did before, but leave the clear tube attached and the emptying flap firmly closed to reduce the mess from the dust falling out the bottom while cleaning the top part.
.
.I eventual gave in to curiosity and removed the three screws in the top or the yellow removable dust collection tube and cyclone bit to see what was in there. The mechanism to release the flap at the bottom of the collection tube does not allow you to remove the lid completely but it does open far enough to get inside. I found the whole top section of the yellow plastic bit blocked by a big plug of compacted dust and a champagne cork. If you are willing to take the risk and have a torx 15 screwdriver handy it that part may be blocked. It did get a bit messy.
.
.If I was going to attempt the same procedure I’d remove the dust collection unit from the vacuum cleaner as I did before, but leave the clear tube attached and the emptying flap firmly closed to reduce the mess from the dust falling out the bottom while cleaning the top part.
Read Full Q/A … : Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
On my M&S Air Vac AV425 central vaccuum system, the system usually turns on by inserting the vaccuum hose into one of the vaccuum outlets. However, it now runs continuously. I am able to turn it off only by unplugging the vaccuum from the electrical outlet. I would like to know how to trouble shoot the problem or how to find someone who services Air Vac systems in the Bridgewater, New jersey area.
ANSWER : We are a central vacuum service company and we service all of new jersey. sounds like you have a short some where that keeps your unit running or it could be your relay module thats stuck our number is 908-721-7595 its j&j central vacuum services
Read Full Q/A … : Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
Dyson vacuum I have a DC07 vaccuum. The problem I am having is that the front does not want to stay down as I vaccuum and I continuously have to keep stepping on the front to make it go back down to the floor. It seems as though there is either not enough weight in the front or possibly the unit just has to be broken in so that there is not so much resistance between the handle and the front of the vaccuum. Could there be something I did not remove or is this typical on these vaccuums?
ANSWER : There is some thing broken it is two plastic cogs they help the front go down and stay up you will have to get a star screw driver and there should be two screws on top and two at the bottom when you have undone them all you will see what i mean take them out only if there broken if there ok put them back in place and put the top and bottom back together if there broken get new ones or put in back together and you will have to lean it up all the time if you want new ones go to www.ebay.co.uk or .com don’t for get to wright down your model number its much easy good luck
Read Full Q/A … : Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
