Simplicity Vacuums\015 Is their a fuse if so how do I access it\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
The suction motor creates vacuum pressure and suction by rotating a motor fan. The impeller rotates at an incredibly high speed of about 30,000 to 35,000 RPM. A suction motor`s power is measured by multiplying the rate of air flow and the vacuum pressure, which induces air flow from the brush through the hose.
Locate the Thermal Motor Reset button on the back of the vacuum. Press button and resume vacuuming. If problem continues, contact your Authorized Simplicity Retailer.
A powerhead vacuum comes fitted with a separate motor in the floor head to drive the motorised brush and effectively eliminate allergen triggers. Proven to be more powerful than a regular floor head tool, it`s the best cleaning tool to help those living with allergies or asthma.
Cleaning your vacuum after every use
For bagless vacuum cleaners, empty the dust bin, and clean the cleaning head and brush rollers. You can remove tangled hair and threads from the roller head with scissors. If the floor head has a brush roller, you can usually remove it for easy cleaning.
First, check that the cord is properly connected to the vacuum cleaner (again, this is surprisingly easy to overlook) and that there are no splits in the rubber. If the cord is damaged, it will need immediately repairing or replacing. The on/off switch can break over time and need replacing.
A damaged vacuum hose, clogged motor air filter or bad suction motor can cause the vacuum cleaner to shut off during use. A tripped overload on the vacuum suction motor can shut off the vacuum cleaner during use. If your vacuum has a reset button, push it; if the vacuum seems hot, let it cool off first.
If you need to vacuum bare floors only, you do not need a powerhead or a power nozzle as it`s called. If you will be using it on carpet, be sure that you purchase one with a power nozzle, which is a motorized beater.
The suction power is to be measured at the end of the tube of a complete vacuum cleaner (i.e. with tube, hose and filters – but without nozzle). Some manufacturers show the results from measurements made at the suction of the actual vacuum cleaner.
Most vacuum machines are equipped with motors that use anything from 500 to 3000 watts of electricity, with the typical unit using around 1,400 watts.
Yes, most hair is okay, but don`t use your vacuum for large amounts of hair at once. Long hair can get tangled around the brush roll and clog up your vacuum. Sweep up large piles of hair (such as after a big DIY haircut) before going in with your vacuum.
Step 5: Wash Vacuum Parts
Place the removed vacuum parts in a sink or tub filled with warm, soapy water. Soak and rinse everything well with hot water. Use a faucet sprayer to quickly remove tough dirt and sticky residue. If needed, scrub with a sponge or microfiber cloth.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
The most common problem with a vacuum cleaner is also the easiest to remedy: clogs in the hose or attachments. Also the electrical cord, motor, switch, fan, brushes, and motor bearings can all need repair or replacement. The drive belt may need replacing; and the attachments, hoses, and filters may need unclogging.
The average life expectancy of a mid-range vacuum cleaner is about six years. You can fix or replace things like blocked filters, jammed brush rolls, frayed hoses, worn-out stick vac batteries and broken accessories yourself.
Low compression, an intake leak or tight valves also can cause low vacuum at idle. If the vacuum reading fluctuates within the normal range-the gauge needle bounces around a lot-uneven compression (broken rings or leaking valves or head gasket in one or two cylinders) is a likely culprit.
Vacuum System Failures:
Occurs when the vacuum pump fails or when both intakes are blocked.
Plug the power cord into your power source. Now arc a wire across the low voltage terminals. You should see a little spark when you touch the terminals and you should hear a “click” inside the board. If there is no spark, then the transformer is bad.
Attachments are quite easy to clean – just fill a sink or bucket with warm water and about a teaspoon of dish soap and drop them in. For any attachment that has hair stuck in it, you can use your cleaning toothbrush to brush it away.
The roller brush makes it possible to get dirt out of carpets. The roller brush is the combination of a belt, a roller, and sometimes a small vacuum head motor. The roller spins, and the bristles attached to it sweep up debris that then gets sucked into the dirt container of the vacuum.
After a year or so, you may need to replace your vacuum`s beater brush. If the bristles seem to be squished, broken or are varying heights, it`s time to replace the brush. These can be found online with the vacuum`s brand and model of your vacuum cleaner.
To fix a clog in the hose, feed one end into a garbage bag, and poke the other end with the back of a mop pole, until you push the clog material out into the garbage bag. To fix a clog in the vacuum, whether it is a canister or bag, use your finger to feel for a clog. Pull as much of it out as you can and discard.
Vacuum pump oil is essential in keeping your vacuum pump operational. It lubricates the pumping machine, while also collecting contaminants and moisture from the evacuated systems.
To get excellent suction power, have a higher HP. If you have already vacuuming stuff, any 1-2 hp vac will do for removing dirt, san, and all types of debris. You are recommended to go for 4-5 hp.
Any negative pressure significantly below standard atmospheric pressure (760 Torr/mmHg, 29.9 inHg or 14.7 PSI) is considered a vacuum.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
Read Full Q/A … : Simplicity Vacuums
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Simplicity Vacuums
Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?
ANSWER : Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I’m surprised it lasted as long as it did.
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)
Read Full Q/A … : Simplicity Vacuums
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
ANSWER : The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal.
Read Full Q/A … : Simplicity Vacuums
My home has a central vacuum system hook-up but no vacuum installed. My friend upgraded his central system and gave me his Eureka Mega Boss central vacuum system and the accessories, including the pow
ANSWER : The power head requires 120 Volts. Some hoses have a receptacle in the handle for the power head plug, and the hose has a cord at the wall inlet end that plugs into a receptacle. Some hoses have a plug at the wall inlet end that plugs into a 120Volt receptacle built into the inlet. The hose plugs into this receptacle when you push the hose into the inlet. The power for this built-in receptacle is wired with line voltage when the system is installed.
Read Full Q/A … : Simplicity Vacuums
I have a Kirby G4 Vacuum Cleaner – MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I’ve had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
ANSWER : Hello,
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci
Read Full Q/A … : Simplicity Vacuums
I have a tank style vacuum. When I vacuum with the power head it dims and slows down when I push the power head back and forth, but it powers back up louder when I stop pushing it If i remove the powerhead from the hose the vacuum works fine.
ANSWER : Most likely the belt. Thats the cheapest so try it first
Read Full Q/A … : Simplicity Vacuums
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would “heave” (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won’t turn. Any suggestio
ANSWER : Carpet brush won’t turn when vac on
Read Full Q/A … : Simplicity Vacuums
