el), my power nozzle works fine when I turn on the switch. If you think it is the switch, can I get a part for it?
Vacuums
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If the vacuum cleaner stops suddenly, the filters should be checked to make sure that they are not blocked or that they require changing. This applies to both bagged and bagless models. Also check if the nozzle or hose are blocked.
Loose connections will cause your vacuum cleaner to lose suction. Make sure that the dust container, the hose, the tube and the brush are all attached properly. If the problem continues, your vacuum cleaner might have a technical problem. If you suspect this to be the case, contact an authorised service agent.
Vacuums often cause “nuisance tripping” with AFCI circuit breakers because vacuums produce a small amount of sparking as they run. And because sparks are essentially small electrical arcs, they`ll occasionally trip your AFCI breaker. Other devices that are prone to “nuisance tripping” include: Flat screen TVs.
Canister vacuums separate the motor and dirt container from the handle and (power) head. A hose connects the handle and head to a canister which houses the motor and dirt container. The choice of canister vs. upright vacuums depends heavily upon your usage, personal preference, and budget.
A strong odor from the shellac that coats the copper coil windings is an indicator that the motor is about to or has burnt out. If the motor is still running, even if it turns on and off by itself as it is heating and cooling, you can still run the motor until it gives up for good.
The suction power is to be measured at the end of the tube of a complete vacuum cleaner (i.e. with tube, hose and filters – but without nozzle). Some manufacturers show the results from measurements made at the suction of the actual vacuum cleaner.
A damaged vacuum hose, clogged motor air filter or bad suction motor can cause the vacuum cleaner to shut off during use. A tripped overload on the vacuum suction motor can shut off the vacuum cleaner during use. If your vacuum has a reset button, push it; if the vacuum seems hot, let it cool off first.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Electrolux Epic 6500 SR …no power to power nozzle. I think it is the switch in the handle because if I use my friend’s hose/handle (same model), my power nozzle works fine when I turn on the switch. If you think it is the switch, can I get a part for it?
ANSWER : That’s about the best one to narrow down a problem, however, there could also be a break in your hose wiring. Switches, hoses, and hose handle assemblies are all available at your local Aerus Electrolux store. Simply take your entire machine in so they can check it to be sure what the problem is.
.The nearest store can be found using the below site. Simply type in your zip code and press enter.
.http://www.aerushome.com/storelocator/
.The nearest store can be found using the below site. Simply type in your zip code and press enter.
.http://www.aerushome.com/storelocator/
Read Full Q/A … : Vacuums
Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head.
Is there anything else I can try? Model Callisto
Is there anything else I can try? Model Callisto
ANSWER : Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor.
Keep in mind this is repairable, and if the unit is less than 5 years old it should still be under warranty.
Good luck .
Read Full Q/A … : Vacuums
We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work
ANSWER : It could be the motor. I’m having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the carbon brushes wear down which is normal. However, the contact wire from the brush to its connector is set so that when the brush wears down, the wire is short enough to stop the spring etc from damaging the commutator. The end result is that you get an intermittent operation of the motor before it finally dies.
.I believe all the DYSONs come with the option of both motors and you cannot really tell which motor you have until you take the thing to bits. You also cannot change motors without changing various other parts on the hoover. On my DC 05 the writing on the YDK motor tells you which one it is.
.This website www. tasweb.org ,select the DC 05 option and scroll down tells you how to take the thing to bits. A search on google etc for your DC 07 may give similar results. Best of luck!
.I believe all the DYSONs come with the option of both motors and you cannot really tell which motor you have until you take the thing to bits. You also cannot change motors without changing various other parts on the hoover. On my DC 05 the writing on the YDK motor tells you which one it is.
.This website www. tasweb.org ,select the DC 05 option and scroll down tells you how to take the thing to bits. A search on google etc for your DC 07 may give similar results. Best of luck!
Read Full Q/A … : Vacuums
Electrolux Renaissance power nozzle turning on and off, brass pins hot
ANSWER : The deal with the Renny is that it runs off of circuit boards. Usually the problem of the main motor shutting on and off is caused by one of the Triac boards located inside the canister. Another problem could be the thermostat wire located on the inside of your motor itself. It’s almost never the thermostat, so the triac board is most likely the issue.
.
.As far as your power nozzle goes, the head eminating from the swivel body is in most cases due to an older design of the power nozzle. I would suggest investing in a new elbow assembly that includes a new swivel body as well as newer style of wiring that is proved to reduce arcing and heat production within the power nozzle.
.
.In some cases, fixing the power nozzle will fix the problems you are experienceing with the main motor as the arcing happening in the power nozzle can in fact turn off your machine. So investing in a new elbow assembly for your power nozzle could in fact solve the problem in its entirety.
.
.As far as your power nozzle goes, the head eminating from the swivel body is in most cases due to an older design of the power nozzle. I would suggest investing in a new elbow assembly that includes a new swivel body as well as newer style of wiring that is proved to reduce arcing and heat production within the power nozzle.
.
.In some cases, fixing the power nozzle will fix the problems you are experienceing with the main motor as the arcing happening in the power nozzle can in fact turn off your machine. So investing in a new elbow assembly for your power nozzle could in fact solve the problem in its entirety.
Read Full Q/A … : Vacuums
The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections:
1 at the handle / upper wand
1 at the lower wand top of the power brush attachment
1 at the handle / upper wand
1 at the lower wand top of the power brush attachment
I replaced the entire wand assembly and it worked great for a year or so and now it’s doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu
ANSWER : This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it is plugged in together.
Read Full Q/A … : Vacuums
Hoover on off switch won’t turn off. I have to unplug the vacuum to stop it. I have dismantled the handle and now I can’t get the inditation in the handle to fit over the little silver knob. I saw there was an on/off switch under the handle that is controlled by a piece of the handle.
#1 question for the manufacturer is why don’t they put the switch on the outside instead of having gimicks that turn it on and off… arghhhhhhhh
#1 question for the manufacturer is why don’t they put the switch on the outside instead of having gimicks that turn it on and off… arghhhhhhhh
ANSWER : Don’t know what model you have, but sounds like you will need to replace the switch. As far as your question, you will have to contact the manufacture for an answer. We only provide solutions to your problem and a model number would have helped.
Read Full Q/A … : Vacuums
I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons…nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I’ve check the bags, filters, cleaned the hos
ANSWER : It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!!
Read Full Q/A … : Vacuums
Our dustbuster (dont’ have model number with me-sorry) won’t turn off when I pull back on the switch handle. I disassembled the unit and realize that the tab on the switch handle that pulls back on the internal switch handle to turn it off is not strong enough for its simple task. Does B&D have a proper replacement part?
ANSWER : If you can provide a model number, I can check availability of the switch and can either order it for you, or supply the B&D part number and you can order it from most local vacuum shops in your area or from Black & Decker direct online: http://www.blackanddeckerservicenet.com/servicenet_home.aspx?AspxAutoDetectCookieSupport=1
Read Full Q/A … : Vacuums
