Vacuums\015 My vax machvx2 isn’t picking up anything its just bought new aswell\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
The most common cause of loss of suction is that the filters have become blocked. They may require cleaning or replacing. Another cause could be that the vacuum cleaner hose is blocked.
To resolve this, remove the dirt container, empty and clean the seals. Replace and try the vacuum again. If you`ve noticed that your Vax vacuum cleaner isn`t performing as well as it usually is and not picking up, the most likely cause would be a blockage. Remove the floorhead and place your hand over the tube.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
Putting in the incorrect amount of oil, putting in the wrong type of oil, and oil contamination can all cause the pump to not reach full vacuum. For this reason, you must check the oil regularly to ensure that it is not only clean, but also properly filled.
Often when your machine is not picking up it is due to loss of suction. If your vacuum cleaner turns on but won`t pick up on carpet or bare floors, something is impeding suction. You may need to change the vacuum bag, unclog the hose, replace/clean the filters, replace the hose, change the belt, or repair the motor.
What`s happening with your vacuum cleaner is that a clog has built up and debris being agitated by the roller is spitting out or stirring up dust without sucking it in.
Gravity and friction are the two main forces that make vacuum suction work. While gravity pulls molecules in the air toward the earth, creating an atmospheric pressure, the suction cup and vacuum pump cause a pressure difference, attaching both surfaces.
All vacuum cleaners operate based on air flowing from the opening at the cleaning head or tool, through the vacuum cleaner and the bag and/or filter system and then out the exhaust port. This airflow is created by the vacuum motor, which also may be referred to as the suction motor.
Low suction or poor pick-up may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action, check for clogs. First, remove the Easy Empty dirt tank from the vacuum and discard all dirt and debris.
The most important indication for the proper function of a vacuum pump is its ability to reach its specified final pressure, or ultimate vacuum. This can be determined with a calibrated gauge to measure the pump`s ultimate vacuum. If no such gauge is available, users can perform an initial function test.
The most common cause of vacuum cleaner not picking up dirt properly is clogged air filter. Remove the filter and either clean or replace it as needed.
The level you set your vacuum depends on the height of your carpet. For bare floors, use the lowest or bare floor setting, for short and medium pile carpets use a medium setting and finally, for plush carpets use the highest setting.
What`s happening with your vacuum cleaner is that a clog has built up and debris being agitated by the roller is spitting out or stirring up dust without sucking it in.
Related Articles. Suction generated by a fan motor powers a vacuum cleaner as it pulls dirt through a chamber or hose and then deposits the debris into a bag or a cup. Some vacuum cleaners have a rotating brush or a beater bar at the end of a nozzle to help agitate and sweep dirt into the suction chamber.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
My electrolux oxygen cannister has the “bag change” light on when there is a new bag. The light stays on when the suction power is high (to pick up small particles) and it won’t pick up, but the ight goes off when the suction power is low (to pick up big objects). I changed the hepa filter, cleaned the motor filter and changed bags, but all that didn’t help.
ANSWER : You may have a clog in the hose, and/or the inlet by the brush roll. A clog will turn on that light as well as a full bag.
Read Full Q/A … : Vacuums
Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head.
Is there anything else I can try? Model Callisto
Is there anything else I can try? Model Callisto
ANSWER : Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor.
Keep in mind this is repairable, and if the unit is less than 5 years old it should still be under warranty.
Good luck .
Read Full Q/A … : Vacuums
My filter queen just had the motor rebuilt last year and was basically a brand new unit when I got it back. It is not picking anything up now when I vacuum. The beater bar on the carpet attachment is turning fine and when I take all the attachments off the hose I can feel the suction being created like it should be picking up debris just fine. I have emptied the canister even when it did not have much in it; however, it still will not pick anything up off the carpet. It picks up debris tempo
ANSWER : It sounds as if you have a clog inside the “Power Nozzel”. They mention that there are “no user serviceable parts within the Majestic® Power Nozzle” My advice would be to see if you can see a clog with in reachable distance and try to remove the clog. One way to check for a clog which may work for you is to remove the attachment and shine a flashlight on one of of the attachment and look through the other side and see if you see light, if no light, most likely a clog. Past that you might void the warrenty if you try and open it up the Power Nozzel itself. You may want to ask a Phone service rep about clog removal.
Read Full Q/A … : Vacuums
Cord rewind The power cord is jammed and won’t go in or out. I can’t find a way to get the cover off to have a look at it. Any suggestions please?
Power cord jammed won’t go in or out. Can comeone tell me how to undo the casing to get to the power cord?
Power cord jammed won’t go in or out. Can comeone tell me how to undo the casing to get to the power cord?
ANSWER : Which model do you have..
Read Full Q/A … : Vacuums
My hoover windtunnel is not picking anything up all of a sudden. Also the roller underneith is not spinning. I’ve replaced filters and the attachment part is working fine, just when it’s in the upright position it won’t pick anything up. It also doesn’t seem to be self propelled anylonger either. It use to **** everything up, including the dog. Please help!
ANSWER : The belt that drives the brush roll has broken. That’s why it doesn’t pick up and why it doesn’t pull itself forwards. Check the User Manual (download from Hoover website if necessary) for information on replacing the belt. Good luck!
Read Full Q/A … : Vacuums
The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections:
1 at the handle / upper wand
1 at the lower wand top of the power brush attachment
1 at the handle / upper wand
1 at the lower wand top of the power brush attachment
I replaced the entire wand assembly and it worked great for a year or so and now it’s doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu
ANSWER : This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it is plugged in together.
Read Full Q/A … : Vacuums
Power head has power but motor won’t run
ANSWER : Circuit brealer switch may be bad, but the fact that Rainbow nozzle made this strange sound makes me think that it may have happened because there is something wrong with the motor.
.
.While unplugged – remove the brush and belt. Try turning brush ends – see if they yurn easily… Try turning the motor shaft – see if it turns and if it does – if it turns smoothly and if makes any strange sounds…
.
.To really test the motor you can just bypass the circuit breaker switch.
.
.While unplugged – remove the brush and belt. Try turning brush ends – see if they yurn easily… Try turning the motor shaft – see if it turns and if it does – if it turns smoothly and if makes any strange sounds…
.
.To really test the motor you can just bypass the circuit breaker switch.
Read Full Q/A … : Vacuums
Eureka power plus suddenly won’t pick up anything
ANSWER : Belt will not turn
Read Full Q/A … : Vacuums
