Hoover SteamVac F5914-900 SpinScrub Upright Vacuum\015 First it wouldn’t ****. Then I smelled something like burned rubber. Now it won’t turn on at all. It’s only 6 months old.\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Should the brush not rotate freely there may be debris tangled around the ends of the brush, carefully remove any obstructions or replace the brush with a new one. We recommend that you fit a new belt and brush once per year to keep your Reactive vacuum working efficiently.
If the cleaner is still not spraying despite the water and detergent tanks being full, there may be a bubble of air stuck in the pump or the hose. To fix this, you need to turn the cleaner on and lower the hose down to the floor. Next, prime the pump by holding down the trigger for up to 1 minute.
`Tripped` reset systems are the most common reasons for a brushbar not turning, but there are some other less common reasons too. These include: If the bearings on the end of the brushbar have seized, you won`t be able to turn it at all. This will often result in a broken belt as well, so be aware of this.
If the product is not making steam please check that there is water in the tank fitted at the top. If the product is not making steam please check that there is water in the tank fitted at the top. Pull the tank up and fill it up with water. Please do not add any cleaning solutions to the water in the tank.
Inspect the vacuum hose for any small holes, kinks, or cracks. Any cracks or holes will decrease the amount of suction in the hose and will not allow the carpet extractor to properly remove liquid from the floor. The hose will need to be replaced if there is damage.
If your vacuum cleaner keeps turning off, this could be due to the following reasons: Blockages – check the hose and head for any obstructions. Filter – always check your filters, if these are clogged this could be causing the vacuum cleaner to work harder and lose suction power.
Lack of power, a bad power cord, failed drive motor or broken wires in the vacuum hose can prevent the vacuum cleaner from starting. Make sure the electrical outlet that you`re using for the vacuum cleaner works. Try using a different outlet if you suspect that the outlet you`re using is dead.
If the dryer hums but does not start, the start switch is not at fault. If the dryer does not respond or make any noise, the start switch could be at fault. Use a multimeter to test the start switch for continuity. If the switch does not have continuity, replace it.
This usually occurs if the dust cannister is too full or the filters are clogged and the motor wasn`t getting enough cooling air passing over it.
– Some vacuums have an in-line thermal fuse (often located between the switch lead and the motor coil). If the fuse is blown it will need to be replaced. – Check your home circuit breaker – it may have tripped. – Some vacuums have a brushroll on/off control.
The most common reason for vacuum motors failing is overheating. Most `dry` vacuums have a flow-though motor. These motors use the air they have sucked up the dust with, to cool themselves. When there is a blockage, flow-though motors are unable to cool themselves due to the lack of airflow.
First, check to make sure the unit is plugged in and is in a working outlet. Next, check to make sure there is water in the tank. It is very important to make sure you are ONLY using water to fill the tank. Other solutions may cause breakdown of the gasket and/or other parts of the machine.
Check the hoses, filters, and rollers if you have a suction problem. A vacuum that loses suction is pretty useless, but the problem is often nothing more than a clogged roller, hose, or filter. To inspect these parts, unplug your vacuum, then turn it over and see if you can manually spin the roller.
Grab the clog with a pair of needle-nose pliers and pull it out. Open a pair of needle-nose pliers and feed it into the end of the lower hose. Once you feel the clog, pinch the blockage with your pliers to get a good grip on it. Pull the clog out of the hose and throw it away.
The average life expectancy of a mid-range vacuum cleaner is about six years. You can fix or replace things like blocked filters, jammed brush rolls, frayed hoses, worn-out stick vac batteries and broken accessories yourself.
The suction power is to be measured at the end of the tube of a complete vacuum cleaner (i.e. with tube, hose and filters – but without nozzle). Some manufacturers show the results from measurements made at the suction of the actual vacuum cleaner.
The problem may lie in your vacuum cleaner`s adapter, charging dock, or battery and the electrical outlet. Try plugging your vacuum cleaner in to another outlet. If it is now working, the problem was in the first outlet that you have used. You should contact a certified electrician if you need to fix that outlet.
How Vacuum Switches Work. Once the switch registers a change in the negative pressure based on the preset sensitivity of the setpoint, the diaphragm of the switch will open or close the attached circuit, turning off or powering on a device. Vacuum switches can be used with NO and NC states.
To rectify the problem, you will need to disconnect the head of the Vax carpet cleaner from the wand section. You`ll then need to clean out any obvious dirt from the head and reattach the head to the wand again. When this is done, you`ll need to set the brush bar to `on` and you can carry on cleaning.
Check for a clogged hose or filter; unclog the hose and replace the filter, Wait 45 minutes for the vacuum to cool; then plug in the vacuum, Turn the power switch to the `I-On` position to start the vacuum. If the vacuum still does not start, contact Customer Service at 1-800-798-7398.
If your dryer turns on but won`t start, the controls may not be operating as expected due to incorrect settings or user error. If your dryer won`t start but does turn on, ensure the following: The “Start” button and electric controls are being pressed firmly. The dryer door is firmly closed and latched.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
The brushes on the Hoover All Terrain Steamvac won’t turn. However, when I try to turn them manually they will turn. So, why won’t they turn when the machine is turned on?
ANSWER : Some vaccums have a belt on the brushes. might need a new one if it does have the belt
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Elna Top 300 sewing machine. I need manual to operate this machine. I have already found out that Elna contracted with Tiwan(excuse my spelling) to make there machine between 1989-1991. I want to know which machine made in Switzerland is comperable to this one. Thanks…Audrey
Sorry about the catagory…but you do not have sewing machine on list.
Sorry about the catagory…but you do not have sewing machine on list.
ANSWER : Isoj:
.
.I have this machine. I use it for my heavy sewing, as it will go through anything. I would be happy to copy the manual and send it to you for copy costs. Just let me know. I would love to know what knowledge you have gained about this machine. It does not appear to be an easy machine to find info on, may not have produced a lot? I had no idea it was not a European produced machine.
.
.Lisa
.
.I have this machine. I use it for my heavy sewing, as it will go through anything. I would be happy to copy the manual and send it to you for copy costs. Just let me know. I would love to know what knowledge you have gained about this machine. It does not appear to be an easy machine to find info on, may not have produced a lot? I had no idea it was not a European produced machine.
.
.Lisa
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
The Vaccum is not turning on when i plug the hose into the wall. The hoover system will turn on when i turn the switch on at the base and wont go off till i turn the switch off. But it will not come on automatically when i put the hose in to the wall connections.
Many Thanks
Linda
Many Thanks
Linda
ANSWER : You can test this out by taking a small metal spoon and with the bottom side of the spoon insert it into the vac outlet on the wall. you want to touch the two metal pins inside the vac outlet to test if the unit is the problem or the hose is the problem.
.
.If the unit starts, the hose should have a 3 year warranty on it. I recommend you have your nearest beam dealer check it out.
.
.If the unit does not start, it has a 7 or 10 year warranty, the circuitry should be replaced. Again have your nearest beam dealer check it out.
.
.good luck
.
.If the unit starts, the hose should have a 3 year warranty on it. I recommend you have your nearest beam dealer check it out.
.
.If the unit does not start, it has a 7 or 10 year warranty, the circuitry should be replaced. Again have your nearest beam dealer check it out.
.
.good luck
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Shark Euro pro mop the ligt wont turn on anymore.
ANSWER : My husband fixed my shark steamer by taking it apart and testing it wire by wire .the problem ?a fuse hidden inside the unit..unscrew the screws and get inside the steamer .at the bottom of the steamer there is a gold orange foil looking piece .under that is a small fuse .unless you can find another fuse just cut that one off and rewire the wires together .shark now comes on
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Belt wont turn makes a loud noise when put on carpet setting
ANSWER : If this is a Dyson with a protected belt that can’t be replaced then it will have to be sent out to Dyson or get a Dyson servicepersonnel to check it over – protected belt motors are difficult to fix by yourself. If its clicking all the time, then it means the belt has to be replaced. In the mean time check that there are no obstructions on the beater bar and behind it and also check that the brush stop roller at the top of the hood is in the right position. It should move automatically when the handle is swung down in normal operation.
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Spin brushes wont spin and the switch wont turn machine off. I have to unplug it.
ANSWER : For the spin brushes it is most likely the motor is fried if you smell something burning it could be jammed or the wires have be shaken off the motor terminals. for it not turning off you need a new switch.
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there’s two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it’s a ribbed belt? that is the water pump belt?
ANSWER : Just taken ours apart with the same problem… found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places – the bottom of the screw wells..This means that the water tank cannot exert sufficient pressure on the valve to release the water..Only solution is a new top cover assembly
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would “heave” (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won’t turn. Any suggestio
ANSWER : Carpet brush won’t turn when vac on
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
